The impacts of cattle access points on deposited sediment levels in headwater streams in Ireland

Cattle access to streams has been linked globally with degradation of stream water quality, driven largely by bank erosion and resultant instream, fine sediment deposition. The majority of evidence on such effects is however based in arid and semiarid regions of the United States and Australia, with few studies relating to cool temperate climates such as Northwest Europe. In this study, “Quorer” resuspendable sediment samples were taken from riffle geomorphic units upstream (control) and at two points downstream (pressure and recovery) of cattle access points in headwater streams in agricultural catchments in Ireland to assess levels of deposited stream sediment. Samples were taken in April/May (2016) prior to the grazing season and in October (2016) at the end of the grazing season. Sites in good‐high ecological status catchments and less than good ecological status catchments were included in the study. Higher levels of sediment were found downstream of cattle access points in both good‐high status and less than good status catchments; however, the impacts of access points were spatially confined to, in most cases, the area immediately downstream of the point of access. There was a strong correlation between deposited sediment mass and organic matter (OM) mass, with levels of OM increasing linearly with deposited sediment mass. Levels of measured sediment were negatively correlated with riparian habitat health (measured using a qualitative habitat assessment). The results of this study highlight the need for measures to prevent cattle access to headwater streams where access points can be many in order to manage local habitat quality and downstream water quality issues.     

Stabilization of 6H-Hexagonal SrMnO3 Polymorph by Al2O3 insertion

We demonstrate the structural evolution of polymorphic phases in Al₂O₃-inserted SrMnO₃ ceramics synthesized by solid state reaction. While the 4H-hexagonal phase is predominant in pure SrMnO₃ ceramics, a small amount of 6H-hexagonal polymorph is identified in addition to the primary 4H-hexagonal SrMnO₃ and the secondary hexagonal SrAl₂O₄ phases in the as-sintered ceramics, evidenced by x-ray diffraction and subsequent Rietveld refinement analyses. The existence of the 6H-hexagonal SrMnO₃ phase is corroborated using Raman spectroscopy. The chemical compositions and electronic structures of the Al₂O₃-inserted SrMnO₃ compounds are also examined using energy dispersive spectroscopy and x-ray photoelectron spectroscopy, respectively. The first-principles calculations reveal that there is no clear difference between the total energies of 4H- and 6H-hexagonal polymorphs regardless of the presence/absence of Sr and oxygen vacancies. Possible origins are discussed with the estimation of actual strain based on the refined lattice parameter of 6H SrMnO₃.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Spreading and Curing Behaviors of a Thermosetting Droplet-Silicone on a Heated Surface

Thermosetting materials are widely used as encapsulation in the electrical packaging to protect the core electronic components from external force, moisture, dust, and other factors. However, the spreading and curing behaviors of such kind of fluid on a heated surface have been rarely explored. In this study, we experimentally and numerically investigated the spreading and curing behaviors of the silicone(OE6550 A/B, which is widely used in the light-emitting diode packaging) droplet with diameter of ～2.2 mm on a heated surface with temperature ranging from 25 ℃ to 250 ℃. For the experiments, we established a setup with high-speed camera and heating unit to capture the fast spreading process of the silicone droplet on the heated surface. For the numerical simulation, we built a viscosity model of the silicone by using the Kiuna's model and combined the viscosity model with the Volume of Fluid(VOF) model by the User Defined Function(UDF) method. The results show that the surface temperature significantly affected the spreading behaviors of the silicone droplet since it determines the temperature and viscosity distribution inside the droplet. For surface temperature varied from 25 ℃ to 250 ℃, the final contact radius changed from ～2.95 mm to ～1.78 mm and the total spreading time changed from ～511 s to ～0.15 s. By further analyzing the viscosity evolution of the droplet, we found that the decreasing of the total spreading time was caused by the decrease of the viscosity under high surface temperature at initial spreading stage, while the reduction of the final contact radius was caused by the curing of the precursor film. This study supplies a strategy to tuning the spreading and curing behavior of silicone by imposing high surface temperature, which is of great importance to the electronic packaging.     

切向结构永磁同步电机磁钢径向并联组合研究

针对低速大转矩切向结构永磁同步电机中磁钢尺寸对性能的影响进行研究.提出一种"工"字形排布的磁钢径向并联组合优化方案.在保证电机磁钢轴向长度和体积不变前提下,分析磁钢磁化方向长度变化对电机性能的影响.分析表明:磁钢的磁化方向长度在一定范围内增加可降低磁钢漏磁、增大反电动势和降低转矩波动;但磁钢的磁化方向长度过度增加会大大降低电机磁通面积,使得电机反电动势不增反降.在此基础上,提出一种降低磁钢漏磁、增大反电动势和降低转矩波动的三块磁钢径向并联组合的"工"字形排布方案:近气隙侧和近隔磁槽侧磁钢槽内分别插入磁化方向长度短、径向宽度窄的磁钢以降低近气隙侧和近隔磁套侧磁钢漏磁;近气隙侧磁钢和近隔磁槽侧磁钢之间采用磁化方向长度较短的磁钢以保证磁钢磁通面积降低得不多.通过仿真实验验证所提方案的可行性.     

On the capacity of the state‐dependent interference relay channel

This paper considers the state‐dependent interference relay channel (SIRC) in which one of the two users may operate as a secondary user and the relay has a noncausal access to the signals from both users. For discrete memoryless SIRC, we first establish the achievable rate region by carefully merging Han‐Kobayashi rate splitting encoding technique, superposition encoding, and Gelfand‐Pinsker encoding technique. Then, based on the achievable rate region that we derive, the capacity of the SIRC is established in many different scenarios including (a) the weak interference regime, (b) the strong interference regime, and (c) the very strong interference regime. This means that our capacity results contain all available known results in the literature. Next, the achievable rate region and the associated capacity results are also evaluated in the case of additive Gaussian noise. Additionally, many numerical examples are investigated to show the value of our theoretical derivations.     

The generalized discrete ‐centroid problem

The ‐centroid problem or leader–follower problem is generalized considering different customer choice rules where a customer may use facilities belonging to different firms, if the difference in travel distance (or time) is small enough. Assuming essential goods, some particular customer choice rules are analyzed. Linear programming formulations for the generalized ‐medianoid and ‐centroid problems are presented and an exact solution approach is applied. Some computational examples are included.     

Assessing students' conceptual understanding using an online three‐tier diagnostic test

When solving a mathematical problem, students who do not have sufficient conceptual understanding may perform poorly and exhibit misconceptions. This study was aimed to examine students' conceptual understanding and significant misconceptions when solving number sense‐related problems. An online three‐tier diagnostic test was administered to 125 fifth‐grade students with varied socio‐economic backgrounds in Hong Kong. Only 14.40% of the students exhibited high performance with high confidence, indicating that these students had a profound conceptual understanding of number sense. In addition, the majority of the students (66.40%) did not demonstrate number sense; these students exhibited several significant misconceptions and could solve the questions only by using a rule‐based method or guessing. Accordingly, most students performed unsatisfactorily on number sense‐related problems. This study is imperative in identifying early predictors and provides information for further compatible interventions in the teaching and learning of number sense in Hong Kong in particular and worldwide in general.