用氩气和氯气吹洗的方法从Al—Mg合金中除去钠

用5■公斤批量熔体研究了从Al—Mg合金中除钠,使之降到1ppm水平。采用了不同的方法:用叶轮机械搅拌;叶轮搅拌+MgCl_2盐覆盖;叶轮搅拌+惰性气体(氩气)吹洗,同时用盐覆盖或不用盐覆盖;叶轮搅拌,惰性气体+2％Cl_2吹洗。叶轮有一个单一的气体入口与空心轴相通。本试验给出了Na-时间关系曲线,它是用Na+1/2Cl_2=NaCl反应的化学计算法简单确定的。其理由是气泡熔体的接触面积足够大。在各个试验中发现镁都没有明显的去掉。如果接触面积不够大,除钠应该是由熔体中质量迁移起支配作用。文中也处理了这种情况的动力学。根据各种实验室的试验确定了顶部表面的质量迁移系数。在除去溶解氧的水模型试验中,测定了叶轮不同转速和气体不同流量下的接触面积。这些结果与带有多孔装置的化学工程系统有比较好的一致性。然而,不知道这些结果能否满意地推广到工业规模的装置上。     

MICROSTRUCTURE AND MECHANICAL BEHAVIOUR OF Al-Li-Zr AND Al-Li-Cu-Mg-Zr ALLOYS

The aging response,tensile and impact properties of two kinds of Al-Li based alloys havebeen studied.The microstructure,deformation as well as fracture behaviour in the alloys wereobserved with SEM and TEM.It was found that the mechanisms of deformation and fracturefor different heat-treated alloys with the same chemical composition are quite different.Thecauses leading to the drop of ductility,toughness as well as anisotropy in peak-aged alloyshave been analysed.Finally,possible methods to improve the ductility and toughness of the al-loys have been discussed.     

THERMODYNAMICS OF BAINITIC TRANSFORMATION IN Cu-24 at.-% Al ALLOY

Two driving forces △G~((β_1)+α')and △G~(β_1→β_2+α)for the bainitic transformation have been calcu-lated for Cu-24 at.-% Al alloy.Results reveal △G~(β_1→α')>0 within the transformation tem-perature range 600—750 K.Therefore,the bainitic transformation cannot be initiated by theβ_1→α' shearing mechanism.On the other hand,the driving force △G~(β_1→β_2+α)to produce 5% ofthe α becomes negative only when the composition of the α satisfiesx_(Al)~α≤0.204 at 700 K or x_(Al)~α=0.209 at 750 K.So the bainitic transformation can only proceedby β_1→β_2+α diffusional reaction with different diffusion amount at different temperatures.     

STRUCTURAL DETERMINATION OF TITANIUM-OXIDE NANOPARTICLES BY X-RAY ABSORPTION SPECTROSCOPY

As a potential application of titanium-oxide nanoparticles, it is extremely important to investigate a detailed picture of the surface and interior structural properties of nanocrystalline materials, such as rutile and anatase with diameters 7.0 and 4.5nm, respectively. X-ray absorption spectroscopy has been used to identify the local Ti environment and related electronic structure. We combine the experimental results at the Ti edge in both bulk and nano-crystals to determine the lattice distortion in terms of differently characteristic preedge features and the variation in the multiple-scattering region of X-ray absorption near-edge structure (XANES) spectra. The relationship between the transition peaks and the surface-to volume ratio is also discussed.     

AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

三水铝石与一水软铝石的自行析出

当把浓铝土矿矿浆加热到160℃时,一水软铝石即析出,并在溶出阶段的热交换器器壁上结疤。在赤泥分离状态下,三小铝石便析出在不含一水软铝石的赤泥里。只有一水软铝石存在于赤泥中,始能析出。在赤泥中含有各种矿物时,针铁矿会对三水铝石的析出显示出最大的种子作用。钙的各种化合物都能控制三水铝石的析出,但不能控制一水软铝石的析出。     

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.     

金刚石化学机械抛光垫修整器的发展方向与前景（上）

半导体芯片的生产主要依靠化学机械抛光(CMP)工序使硅片表面平坦化，使复杂的集成电路能非常有效地工作。做为电路设计不可避免地趋向于采用高度集成和多层结构。故化学机械抛光技术必须紧跟其需要与发展。化学机械抛光垫性能的关键是采用金刚石化学机械抛光垫修整器工作时，抛光垫工作寿命期间，必须保持恒定的抛光效果。     

NANO-MULTILAYERS WITH HIGH PERPENDICULAR ANISOTROPY FOR MAGNETIC RECORDING

(FePt/Ag)n nano-multilayers were deposited on MgO (100) single crystal with laser ablation and then subjected to annealing. FePt L1o grains with (001) texture and thus a large perpendicular magnetic anisotropy constant Ku of the order of 106 J/m3 were formed. A thick Ag layer is found to be favorable for decreasing the dispersion of the easy axis for magnetization. The measurement of time decay of magnetization gave rise to a small activation volume of the order of 10-25m3, showing the promising of being the recording medium for future high density perpendicular recording.     

新型三元复合超导线的发展

在现有的三元复合超导线中,一般是用铜作稳定材料。如果使用高纯铝,稳定性将会进一步改善。然而,由于硬度不同,很难把超导体和铝冶金地合成一体。制造埋置在 Cu—Ni 基体内的铝稳定的多芯超导线就更加困难了。既使制成了线材,因为高导电性的稳定材料本身存在涡流损耗,它也未必适合于绕制变化速度为每秒数十万高斯的脉冲磁体。