Oxidation of hafnium carbide and hafnium carbide with additions of tantalum and praseodymium

The oxidation behavior of HfC, HfC-25 wt. % TaC, and HfC-7 wt.% PrC₂ has been studied between 1200–2200° C. Parabolic growth of the oxide layer has been observed for both HfC and HfC-TaC over the entire temperature range. A break in the temperature dependence of the oxidation kinetics occurs around 1600°C. At lower temperatures, the kinetics are limited by gaseous diffusion via pores in the oxide. Above 1800°C, gaseous diffusion through pores becomes less important as scale-growth kinetics are dominated by bulk (ambipolar) diffusion of oxygen and electrons through the oxide.     

THERMODYNAMICS OF MARTENSITIC TRANSPORMATION IN β-Cu BASE ALLOYS

提出对β-Cu基合金热弹性马氏体相变的热力学处理。计算了Cu-Zn,Cu-Al及Cu-Zn-Al合金马氏体相变驱动力,T_0温度及M_s温度,M_s的计算值与实验值符合很好。母相有序降低Cu-Zn和Cu-Zn-Al的M_s,但升高Cu-Al的M_s(T_0)。并简介了两种估算非化学自由能的方法。     

Diagnosis of tapping operations using an AI approach

On-line diagnosis of the machining operations is essential because it can prevent potential problems caused by abnormal conditions. So far, little research has been done for the on-line diagnosis of tapping operations. However, tapping is a very important machining operation. And the on-line diagnosis is essential. In this work, an artificial neural network was utilized for the diagnosis of the tapping operation. The input vector for the neural network is obtained by processing the signals of the thrust, torque, and lateral forces during the tapping operations. A total of ten indices were used in the input layer of the network. The output of the artificial neural network provides the tapping states. Five different tapping states were investigated: normal operation, tap wear, misalignment, oversize hole, and undersize hole. The weights and thresholds of the artificial neural network can be modified by the generalized delta rule. Experimental results showed that diagnosis of tapping operations through an artificial neural network can reach a success rate of over 95%.     

The rapid thermal processing chemical vapor deposition of silicon epitaxial films

The future of ultralarge-scale integration technology is tending toward reduced thermal processing to realize devices with higher integration densities and better performance. Rapid thermal processing chemical vapor deposition (RTPCVD) is a promising technology that can preserve the advantages of high-temperature processing without degrading the fidelity of junction profiles. Defect free, thin silicon epilayers with extremely abrupt dopant-transition profiles can be re-producibly grown by RTPCVD. Very high quality n-type and p-type heavily doped epilayers, using boron, arsenic, and phosphorus as dopants, have been grown by RTPCVD. Through superior process control and reduced thermal exposure, RTPCVD is expected to play an important part in the next generation of fabrication technology and in the development of novel silicon-based materials.     

The multiphase effect on crystal structure, hydrogen absorbing properties and electrode performance of Sc---Zr based Laves phase alloys

The crystal structure, hydrogen absorbing properties and electrode performance of Laves phase alloy systems, Sc---Zr---Ni---Mn and Sc---Ni---V systems, were studied by optical and scanning electron microscopy, X-ray powder diffraction, pressure-composition isotherm and electrochemical measurements. C14 and C15 Laves phases and minor ScNi-related phase were found in the Sc---Zr---Ni---Mn alloy system. The ScNi-related phase was composed of Sc, Zr and Ni elements. Two kinds of minor phase, BCC and ScNi-related phases, were identified in addition to the C15 phase in the Sc---Zr---Ni---V alloy system. The BCC contained mainly the element V. The ScNi-related phase contributed to an increase in the hydrogen capacity, but those in the V alloy system did not. The multiphase anode with a large amount of the ScNi-related phase showed a low durability against the KOH electrolyte. The substitution of Zr by Sc led to an improvement in the initial activation of the anode, but there was not a clear correlation between the presence of the multiphase in the anode and the rate capability.     

Grinding of sol-gel derived alumina-zirconia composites

Alumina-zirconia powders containing 12.5 wt% zirconia were prepared by sol-gel processing. After calcination these powders were cold pressed, sintered and HIPed. The maximum amount of tetragonal form of zirconia is retained in these specimens. Grindability and the transformation behaviour of tetragonal zirconia were evaluated by conducting grinding studies at different speeds and depths of cut. The surface characteristics of the specimens and phase analysis of the specimens and grinding chips were determined. The surface finish improved as the grinding speed increased and with the decrease of depth of grinding. The grinding condition to obtain maximum amounts of tetragonal zirconia was optimized.     

A new method of automatic polishing on curved aluminium alloy surfaces at constant pressure

This paper presents original research results of automatic polishing on curved surfaces of aluminium alloy moulds at constant pressure. The automatic polishing of aluminium alloy material is achieved. A parameter S is defined, which can express the comprehensive influential factors in the automatic polishing process and give a relationship among the polishing quality and the various machining variables. Based on this, a new method for comprehensive control of polishing quality is suggested.