Relation Between Firing Conditions Grain Boundary Structure and Magnetic Properties in Polycrystalline MnZn-Ferrites

The influence of the firing conditions on the nanoscale structure of the grain boundaries and on the magnetic properties of polycrystalline MnZn-ferrites is investigated, on specimens of nearly identical microstructures. High oxygen partial pressures favor accumulation of impurity ions at the triple points. Under appropriate oxygen pressures homogeneous accumulation of impurities along the grain boundaries may occur, revealing therefore chemically pure grains and low hysteresis losses; simultaneously an increase of the grain boundary resistivity occurs that results to low eddy current losses. Managing the raw material impurity cations towards controlled grain boundary structures leads to the synthesis of MnZn-ferrites with power losses similar to those achieved when high purity raw materials are used together with externally introduced additives.     

Investigation of the influence of design parameters on the flow performance of single and double disk viscous micropumps

This paper investigates the effect of radius ratio, and channel aspect ratio on the flow performance of newly introduced single and double disk viscous micropumps. A lubrication solution for the flow field, which accounts for both radius and channel aspect ratios either in single or double disk micropumps was developed and compared with available experimental data and with an approximate solution which estimates for the flow rate only in single disk pump and neglects channel aspect ratio. Additionally, a number of 3D numerical models for single and double disk micropumps were built and analyzed using the finite volume method. Pressure and drag shape factors were introduced to describe the effects of radius and channel aspect ratios on the flow rate. The values of these factors for the whole range of studied parameters are found analytically and numerically. The error in estimating the flow rate was found to be less than 10% for r ₁ /r ₂ > 0.2, and less than 7% for the studied range of h/w. Also, the lubrication solution was found to be in good agreement with the numerical and experimental results.     

Bruchanalyse an Hohlgläsern

Failure analysis of hollow glasses The failure analysis is very important to clarify damages of hollow glasses. Damages of glass bottle through over pressure are very often linked with damages to persons. This is the reason why the causal research is from particular importance. Different surface characteristics of glass fragments as well as the fracture pattern give hints to the direction of the crack, the stress just before breakage and the reason of stress. A reconstruction of the bottle is a further helpful instrument for cause studies. The difference of the various characteristics of the surface will be explained. Further on there will be discussed different reasons and mechanism of fracture.     

Microfabricated preconcentrator-focuser for a microscale gas chromatograph

The design, fabrication, and testing of a preconcentrator-focuser (PCF), consisting of a thick micromachined Si heater packed with a small quantity of a granular adsorbent material are described. The PCF is developed to capture and concentrate vapors for subsequent focused thermal desorption and analysis in a micro gas chromatograph. The microheater contains an array of high-aspect-ratio, etched-Si heating elements, 520 /spl mu/m (h)/spl times/50 /spl mu/m (w)/spl times/3000 /spl mu/m (l), bounded by an annulus of Si and thermally isolated from the remaining substrate by an air gap. This structure is sandwiched between Pyrex glass plates with inlet/outlet ports that accept capillary tubes for sample flow and is sealed by anodic bonding (bottom) and rapidly annealed glass/metal/Si solder bonding (top). The large microheater surface area allows for high adsorption capacity and efficient, uniform thermal desorption of vapors captured on the adsorbent within the structure. The adsorbent consists of roughly spherical granules, /spl sim/200 /spl mu/m in diameter, of a high-surface-area, graphitized carbon. Key design considerations, fabrication technologies, and results of performance tests are presented with an emphasis on the thermal desorption characteristics of several representative volatile organic compounds as a function of volumetric flow rates and heating rates. Preconcentration factors as high as 5600 and desorbed peak widths as narrow as 0.8 s are achieved from 0.25-L samples of benzene at modest heating rates. The effects of operating variables on sensitivity, chromatographic resolution, and detection limits are assessed. Testing of this PCF with a micromachined separation column and integrated sensor array is discussed briefly.     

The oxidation of two ternary Ni-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of the ternary alloys Ni-45Cu-10Al and Ni-30Cu-10Al has been studied at 800-900 °C under 1 atm O₂. The presence of 10 at.% Al reduces significantly the oxidation rate of the corresponding Cu-Ni alloys during the initial oxidation stages, even before the establishment of a complete Al₂O₃ layer. The weight of individual sample of the two ternary Ni-Cu-10Al alloys at 800 °C increases more rapidly than at 900 °C during the initial oxidation stage. As oxidation proceeds, the weight gain at 800 °C slows down to a degree that the total weight gain after 24 h oxidation at 800 °C is less than that at 900 °C. Due to a faster formation of the Al₂O₃ layer, which suppresses earlier the further oxidation of Cu and Ni, the external region of the scales grown on Ni-45Cu-10Al contain much less Cu and Ni oxides than those grown on Ni-30Cu-10Al. The transition from the internal oxidation to the selective external oxidation of the most reactive component Al in Ni-Cu-Al alloys is favored by higher values of the Al content, of temperature and of the Cu/Ni ratio.     

Reibungsversuche mit Krypton bei niedrigen Drücken

Tests of a linear Equation on the Evaluation of Krypton Friction Experiments at low Pressures and Connections to Viscosity Effects The coefficient of viskosity is nearly constant in the region with STP conditions and is independent of the pressure. This coefficient decreases with lowering the pressure until the region of molecular flow is reached. There we have free molecular‐ or vacuum viscosity. Experiments with the friction of gas have to take in the gas between surfaces which are movabel and parallel. Reactions of the gas with the moving surface cannot be neglected. We made our lab‐examinations of gas friction effects between two rotating cylinders. Generally there is a linear equation of the reciprocal values of viscosities and pressures. Our experiments show a region, where this linear relation is valid. This region has a low limit with coming to molecular flow and an upper limit if the gas is warmed up by friction at higher pressures.     

Hochbelastbare kohlenstoffbasierte Mehrschichtsysteme für die Umformtechnik

Carbon based multilayer systems for highly loaded forming tools Amorphous hydrogenated carbon (metal‐free a‐C:H and metal‐containing a‐C:H:Me) films respond very sensitively to local overloads. For example during forming tool operations, hard abrasive particles and locally high stresses on the coating surface can cause crack initiation and early coating failure. Compared to the high hardness, wear resistance and excellent friction properties, in many cases the adhesion of a‐C:H films is relatively insufficient. Adhesion and overload resistance of a‐C:H and a‐C:H:Me, prepared by reactive sputtering, can be influenced in a wide range by different interlayer systems. In the present report the wear mechanism of amorphous carbon coatings and the influence of different metallic, metal nitride and metal carbide interlayers on the growth structure, the adhesion and the load resistance will be reported. Two well adapted multi‐coating systems, successfully tested for highly loaded tools and components, will be presented.     

The myopic intraocular lens in a phakic eye. Initial experience

The very first experiences with implantation of 3 phakic anterior chamber lenses for high myopia correction are presented. After average 4 month follow up good stability and transparation of concave lenses type ZB5M were observed with accurately achieved correction postoperatively.