Fully plastic analyses for notched bars and plates using finite element limit analysis

In the present work, fully plastic analyses for notched bars and (plane strain) plates in tension are performed, via finite element (FE) limit analysis based on non-hardening plasticity, from which plastic limit loads and stress fields are determined. Relevant geometric parameters are systematically varied to cover all possible ranges of the notch depth and radius. For the limit loads, it is found that the FE solutions for the notched plate agree well with the existing solution. For the notched bar, however, the FE solutions are found to be significantly different from known solutions, and accordingly the new approximation is given. Regarding fully plastic stress fields, it is found that, for the notched plate, the maximum hydrostatic (mean normal) stress overall occurs in the center of the specimen, which strongly depends on the relative notch depth and the notch radius-to-depth ratio. On the other hand, for the notched bar, the maximum hydrostatic stress can occur in between the center of the specimen and the notch tip. The maximum hydrostatic stress for a given notch depth can occur not for the cracked case, but for the notched case with a certain radius. This is true for both bars and plates. For a given notch radius, on the other hand, the maximum hydrostatic stress increases monotonically with the decreasing notch radius.     

Preparation of a sensor substrate using functionalized mesoporous silica on a gold film for surface plasmon resonance (SPR) spectroscopy

The use of surface plasmon resonance (SPR) spectroscopy has been applied to a wide variety of fields such as biosensors and surface analysis instruments. In general, a SPR substrate is prepared using self-assembled monolayer (SAM) method of organic molecules as receptor for the target on a layer of gold or silver. However, mesoporous inorganic materials such as SBA-15 have benefits as sensor substrate for SPR. Mesoporous silica has a large surface area which receptor molecule can be attached and has a rigid body which has an excellent stability in the extreme condition compared to organic sensing layer. We prepared an organic modified mesoporous silica and successfully immobilized it on a gold surface, in an attempt to use as a substrate for SPR spectroscopy. For the comparison of sensitivity of prepared substrate, Pt²⁺ detection was selected as a model system. Substrate prepared in this study exhibited the capability of selective sensing for Pt²⁺ ions.     

A novel way to improve the dispersion-limited transmission distance of electroabsorption modulated lasers

We propose and demonstrate a way to improve the dispersion-limited reach of electroabsorption modulated lasers (EMLs). We generate continuous-phase frequency-shift keying/amplitude-shift keying (ASK) signals with the EML by applying a small current modulation to the laser diode (LD) on top of electroabsorption-modulated ASK signals. The amount of frequency deviation induced by the current modulation is adjusted to have the EML output signals experience /spl pi/ phase shift at every space. The experimental demonstration shows that with the proposed scheme we can increase the dispersion-limited transmission distance of the EML-based transmitter by 25%-75%, and it can be further improved by employing an LD with flat frequency-modulation response.     

Inside Front Cover: Photonic Crystal Structures as a Basis for a Three‐Dimensionally Interpenetrating Electrochemical‐Cell System (Adv. Mater. 13/2006)

The inside cover shows an SEM image of a 3D‐interpenetrating electrochemical cell with submicrometer features, as reported by Stein and coworkers on p. 1750. The pores of an inverse‐opal carbon electrode are coated with a conformal layer of a polymer separator and infiltrated with vanadia to form the opposite electrode after lithiation. The idealized scheme illustrates lithium‐ion transport between the electrodes through the polymer membrane.     

Limit of ferrite grain refinement by severe plastic deformation of austenite

High-angle grain-boundary spacing in deformed austenite is analyzed using Ni-30Fe alloy to explain the change of ferrite grain size by severe plastic deformation (SPD) of austenite in low carbon steel. It is suggested that constant high-angle grain-boundary spacing in deformed austenite resulting from dynamic recrystallization (DRX) or geometric DRX is responsible for the limit of ferrite grain refinement over a certain level of plastic deformation of austenite.     

Recrystallization and grain growth of cold-rolled gold sheet

Recrystallization and grain growth of a cold-rolled gold sheet with 98 pct reduction in area (RA) were investigated with electron backscatter diffraction (EBSD) and X-ray diffraction (XRD). Gold with some dopants (Be, Ca, and La) was used in this research and its recrystallization temperature was 320 °C. Isothermal annealing experiments at 400 °C, 500 °C, and 600 °C were carried out for the cold-rolled gold sheet, and recrystallization texture was examined. In the cold-rolled gold sheet, α- and β-fibers were measured mainly and some shear texture components were found on the surface. Shear texture components remained on the surface for 2 hours at 400 °C and were consumed by other recrystallized grains after 24 hours at 400 °C. Microstructure and texture evolution during in-situ annealing at 400 °C were investigated from the cold-rolled state to the fully recrystallized state using EBSD. Most of the newly, recrystallized grains came from the deformed β-fiber regions and consisted of β-fiber, cube, and other random orientations.     

A new LDPC decoding algorithm aided by segmented cyclic redundancy checks for magnetic recording channels

We introduce a new low-density parity-check (LDPC) decoding algorithm that exploits the cyclic redundancy check (CRC) information of data segments. By using the error detection property of the CRC, we can successively decode data segments of a codeword corrupted by random errors and erasures. The key idea is that the messages from the variable nodes with correct checksum are fixed to deterministic log likelihood ratio values during LDPC iterative decoding. This approach improves the decoding speed and codeword error rate without significant modification of the LDPC decoding structure. Moreover, the CRC is also used for an early stopping criterion of LDPC decoding. Simulation results verify our claims.     

Low-threshold vertical-cavity surface-emitting lasers based onoxide-confinement and high contrast distributed Bragg reflectors

The interest in low-threshold vertical-cavity surface-emitting lasers (VCSEL's) is increased by the demonstration of the small size, low loss optical mode due to oxide-confinement in the Fabry-Perot microcavity laser. Intense recent work in this area has resulted in numerous record breaking demonstrations of low-threshold current, high wall-plug efficiency, and high speed. In this paper, we discuss the impact of the dielectric cavity design to enhance control of the optical mode. We argue that high contrast dielectric mirrors can become an important design approach, especially for small apertures limited by diffraction loss. Experimental results are compared for different types of mirror and aperture designs     

Factors Affecting Flow-Mediated Vasodilatation in Hemodialysis Patients

Clinical manifestation of overt vascular disease may be preceded for years by endothelial dysfunction. Objective: This study was undertaken to evaluate endothelial function in ESRD patients and correlation between endothelial function and clinical and biochemical parameters. Methods: 32 stable ESRD patients (male : female = 16 : 16, average age: 55.2 ± 13.0) on hemodialysis were included. A 10‐MHz ultrasound transducer was used to image the brachial artery. Brachial artery diameter was measured, and reactive hyperemia was induced by inflation to 250 mmHg for 5 min and then deflation of a pneumatic cuff. After release of the cuff, brachial artery diameter was measured. Results: In the entire study population and non‐diabetic group, the %FMD (% flow‐mediated dilatation, % change of brachial artery diameter between before and after cuff inflation) did not show any significant correlation with duration of dialysis, age, hypertension, albumin, CRP, total cholesterol, LDL and HDL cholesterol, and triglyceride. However, the %FMD of diabetic patients was lower than that of non‐diabetics. Among the patients with diabetes, the group of patients with FMD of <5.2% showed significant lower serum albumin and significantly higher ln(CRP) levels compared to the group of patients with FMD ≥5.2%. The %FMD showed significant positive correlation with serum albumin level and significant negative correlation with ln(CRP) in diabetic patients. Conclusion: These findings suggest that endothelial dysfunction, estimated by FMD, was significantly more prominent in diabetic ESRD, especially with low serum albumin and high CRP levels.     

Design of a Drilling Torque Controller for a Machining Center

In the drilling process, cutting torque control through feedrate manipulation has significant benefits in prevention of tool breakage and reduction of machine tool vibration and tool wear. In this paper, a PID torque controller was designed for real time drilling torque control in a machining centre. The drilling torque was estimated from the spindle motor current and regulated by feedrate control. The plant including the feed drive system, cutting process, and spindle system was modelled for controller design. For a certain cutting condition, the Ziegler-Nichols method was used to determine the proportional gain and derivative and integral control action times of the controller. Also, the root locus plot was used to tune the proportional gain of the controller. A simple method was also suggested to obtain the tuned controller gain instead of the Ziegler-Nichols method and the root locus plot for an arbitrary cutting condition. Experimental works have been performed to verify the performance of the proposed controller. It is shown that the gain tuning is essential for enhancement of the controller performance and the designed controller can regulate the drilling torque well at a given reference level.Nomenclature G_fc(s) transfer function of combined system of feed drive and cutting process - G_s(s) transfer function of spindle system - G_p(s) transfer function of plant - G_CL(s) transfer function of closed loop system - G_con(s) transfer function of controller - _fc1, _fc2 time constants of combined system of feed drive and cutting process - _s time constant of spindle system - K controller gain - K_c cutting process gain - K_s spindle motor current gain - K_plant plant gain - K_cr critical gain - K_p proportional gain of controller - K_{p_tune} tuned proportional gain of controller - I_s spindle motor current - I_u,v,w u, v, and w phase current of spindle motor - I_idle idling current of spindle motor - damping ratio - T oscillation period of system response - T_c cutting torque - T_m motor torque - T_idle idling torque of spindle motor - T_i integral control action time - T_d derivative control action time