Estimation of the Longitudinal Dispersion Coefficient Using the Velocity Profile in Natural Streams

In this study, a theoretical method for predicting the longitudinal dispersion coefficient is developed based on the transverse velocity distribution in natural streams. Equations of the transverse velocity profile for irregular cross sections of the natural streams are analyzed. Among the velocity profile equations tested in this study, the beta distribution equation, which is a probability density function, is considered to be the most appropriate model for explaining the complex behavior of the transverse velocity structure of irregular natural streams. The new equation for the longitudinal dispersion coefficient that is based on the beta function for the transverse velocity profile is developed. A comparison of the proposed equation with existing equations and the observed longitudinal dispersion coefficient reveals that the proposed equation shows better agreement with the observed data compared to other existing equations.     

A New Approach for Built‐in Self‐Test of 4.5 to 5.5 GHz Low‐Noise Amplifiers

This paper presents a low‐cost RF parameter estimation technique using a new RF built‐in self‐test (BIST) circuit and efficient DC measurement for 4.5 to 5.5 GHz low noise amplifiers (LNAs). The BIST circuit measures gain, noise figure, input impedance, and input return loss for an LNA. The BIST circuit is designed using 0.18 μm SiGe technology. The test technique utilizes input impedance matching and output DC voltage measurements. The technique is simple and inexpensive.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

A study of CaCO3 fouling with a microscopic imaging technique

The present study introduces a new experimental method to visualize the fouling process of CaCO₃. A mini-channel heat exchanger system with a microscopic imaging technique was developed for real-time visualization of the fouling process. The present study discussed how scale started initially, how scale formed thick layers, and how a small crystal grew into a large one, touching the adjacent one. Detail microscopic images of scale crystals and corresponding fouling resistances were obtained over the entire fouling process. The microscopic observation indicated that the fouling process could be divided into three stages: an induction period, a period of uniform generation of nuclei, and a period of uniform growth of scale. Sudden appearance of numerous small nuclei indicated the end of the induction period, a key event before the rapid increase in the fouling resistance. The present experimental method using microscopic images of the wet fouling process provides a valuable insight on the fouling mechanism.     

Feasibility of fishmeal replacement by shrimp head silage protein hydrolysate in Nile tilapia (Oreochromis niloticus L) diets

This study provides information on the use of shrimp head silage protein hydrolysate (SPH) as an alternative protein source for tilapia feeding. Six diets (28% protein, 12% lipid) were prepared where fishmeal protein was replaced at levels of 0 (control), 10, 15, 20, 25 and 30% with the hydrolysate. The diets were supplied to Nile tilapia fry (338 mg initial weight) stocked in plastic recirculating 20 l tanks (10 animals per tank), with three replicates per treatment. After an 8 week experimental period, fish fed the diets containing 10 and 15% SPH showed significantly better performance in terms of final body weight, weight gain (%), mean daily weight gain (mg day^?1), specific growth ratio and feed conversion ratio than those fed the control diet (fishmeal as protein source) and higher‐SPH diets. It is concluded that shrimp head hydrolysate is a promising alternative protein source for tilapia feeding, improving growth ratio at dietary inclusion levels as high as 15%. In addition, the diets with added shrimp silage protein were well accepted by the fish, which avidly consumed the feed during the experiment. © 2002 Society of Chemical Industry     

A critical heat flux model based on mass, energy, and momentum balance for upflow boiling at low qualities

A mechanistic modeling of critical heat flux (CHF) in upflow boiling at low qualities is performed. The developed model is based on a physical criterion of CHF occurrence and a mechanism limiting the thermal transport between a stagnant bubbly layer and bulk stream. The mechanism can be mathematically formulated by coupling the equation of limiting mixing mass flux, which is derived from momentum balance equations in two regions, with local mass and energy balance equations on the bubbly layer. The resulting form of the model is represented by a general and straightforward CHF formula involving two empirical constants related to the void fraction and the thickness of the bubbly layer. The predictions agree well with the extensive CHF data of water in uniformly heated tubes.     

NO emission characteristics in counterflow diffusion flame of blended fuel of H2/CO2/Ar

Flame structure and NO emission characteristics in counterflow diffusion flame of blended fuel of H₂/CO₂/Ar have been numerically simulated with detailed chemistry. The combination of H₂, CO₂ and Ar as fuel is selected to clearly display the contribution of hydrocarbon products to flame structure and NO emission characteristics due to the breakdown of CO₂. A radiative heat loss term is involved to correctly describe the flame dynamics especially at low strain rates. The detailed chemistry adopts the reaction mechanism of GRI 2.11, which consists of 49 species and 279 elementary reactions. All mechanisms including thermal, NO₂, N₂O and Fenimore are taken into account to separately evaluate the effects of CO₂ addition on NO emission characteristics. The increase of added CO₂ quantity causes flame temperature to fall since at high strain rates a diluent effect is prevailing and at low strain rates the breakdown of CO₂ produces relatively populous hydrocarbon products and thus the existence of hydrocarbon products inhibits chain branching. It is also found that the contribution of NO production by N₂O and NO₂ mechanisms are negligible and that thermal mechanism is concentrated on only the reaction zone. As strain rate and CO₂ quantity increase, NO production is remarkably augmented. Copyright © 2002 John Wiley & Sons, Ltd.     

Ruthenium dye-sensitized SnO2/TiO2 coupled solar cells

The photoelectrochemical behaviors of RuL₂(NCS)₂ dye-sensitized SnO₂/TiO₂ coupled solar cell was studied and compared with TiO₂ single system. The coupled system shows higher incident photon-to-current conversion efficiency (IPCE) value than the single system. A maximum IPCE value in the coupled system with 3.5 μm-thick SnO₂ and 7 μm-thick TiO₂ attained 82.4% at 530 nm wavelength. The higher IPCE value in the coupled system is attributed to the charge separation by fast electron transfer process from the excited RuL₂(NCS)₂ dye to TiO₂ to SnO₂ in the system with different energy level.     

人力资源投资评价应解决的两个重要问题

阐述了企业人力资源投资财务评价应解决的两个重要问题：评价对象的分类和项目的财务现金流量的内容。