A far-infrared spectroscopic study of low temperature soft phonon mode in Tris-Sarcosine Calcium Chloride(TSCC)

Temperature dependences of the soft phonon frequency and the damping constant in Tris-Sarcosine Calcium Chloride (TSCC) single crystal have been investigated between 5K and 100K by using a Fourier-transform far-infrared spectrometer. It has been observed that the soft phonon frequency decreases gradually and the damping constant increases as the transition temperature is approached from below The damping constant varies from 7cm^-1 a 90K to less than 0.5cm^-1 at 5K. It has been found that the damping constant is approximately proportional to temperature below about 60K.     

Titania NOx sensors for exhaust monitoring

Oxide semiconductors have been examined to develop NO_x sensors for exhaust monitoring. Titania doped with trivalent elements, such as Al³⁺, Sc³⁺, Ga³⁺ or In³⁺, has a good sensitivity and selectivity to NO between 450 and 550 °C, and shows rapid response. A sensor probe for monitoring exhaust NO_x has been fabricated. Many kinds of interference gases, such as C₃H₆, CO and SO₂, have been found to have only a slight influence on the sensor response to NO. The influence of O₂ and H₂O is also negligible, except for the cases of 0% H₂O and fuel-rich conditions. In accordance with these results, the sensor probe operates satisfactority in the exhaust gas of various combustion conditions without interference from the various kinds of gas species in the exhaust gases.     

Preparation of rod-shaped BaTiO3 powder

Rod-shaped BaTiO₃ powder particles have been prepared from rod-shaped TiO₂ ·nH₂O and BaCO₃ in molten chloride. The morphology of BaTiO₃ particles was studied referring to the effects of the chemical species of the starting titanium compound, amount of chloride, particle size of the titanium compound and reaction conditions, and the preparation condition of rod-shaped BaTiO₃ has been determined: i.e., large TiO₂ ·nH₂O particles were heated at 700°C in molten salt with an equal amount of BaTiO₃. This condition was effective in suppressing the formation of BaTiO₃ by a solution-precipitation process as well as the deformation of either TiO₂ ·nH₂O or BaTiO₃, which are responsible for the formation of equiaxed BaTiO₃ particles. The obtained rod-shaped BaTiO₃ particles had a cubic symmetry. Electron diffraction analysis showed that the following topotactic relation is retained; 0 1 0_{potassium tetratitanate} 0 1 0_{hydrated titania} 1 0 0_anatase 1 0 0_{barium titanate}     

Formation of monodispersed Ta2O5 powders

The Ta₂O₅ powders synthesized by the hydrolysis of tantalum pentaethoxide, Ta(OC₂H₅)₅ in alcoholic solution were monodispersed fine oxide particles, which were a uniform, spherical shape, non-agglomerate, and had a narrow size distribution. They grew to 1.2m after ageing for 1 h after hydrolysis. Powder X-ray diffraction and differential thermal analysisthermogravimetric analysis showed the particles were amorphous and hydrated. These particles lost the water at 290° C and gave well-crystalline Ta₂O at 740° C. Throughout these thermal processes, the particle morphology was kept almost the same.     

Growth of Al2O3 whiskers by vapour-phase reactions

Needle-like or wool-like Al₂O₃ whiskers can be grown on a substrate by the hydrolysis of aluminium fluoride vapour. Effects of the growth conditions on the morphology of the crystals and growth processes of the whisker were investigated, and the optimum growth condition of whiskers was examined. Adequate vapour pressure conditions of the reactant gases for the growth of the wool-like whisker were found to be . Aluminium oxyfluoride was assumed to be the most probable intermediate species for the growth of Al₂O₃ whiskers. A variety of crystal morphologies are also shown and described with respect to the experimental conditions.     

Screening of Inhibitors Targeting Heat Shock Protein 47 Involved in the Development of Idiopathic Pulmonary Fibrosis

Heat shock protein 47 (HSP47), a collagen-specific molecular chaperone, is causally related to fibrotic diseases, including idiopathic pulmonary fibrosis. The identification of Compounds that interfere with the HSP47-collagen interaction is essential for the development of relevant therapeutics. Herein, we prepared human HSP47 as a soluble fusion protein expressed in E. coli and established an assay system for HSP47 inhibitor screening. We screened a natural and synthetic Compound library established at Nagasaki University. Among 1023 Compounds, 13 exhibited inhibitory activity against human HSP47, of which three inhibited its function in a dose-dependent manner. Epigallocatechin-3-O-gallate, one of these three Compounds, is a typical polyphenol Compound derived from tea leaves. Structurally related Compounds were synthesized and examined for their activity, revealing a hydroxyl group at A-ring position 5 as important for its activity. The present findings provide valuable insight for the development of natural product-derived therapeutics for fibrotic diseases, including idiopathic pulmonary fibrosis.     

Analysis of Reusability using ‘Marginal Reuse Rate’

While reuse is an effective lifecycle option in terms of reduction of environmental loads and value of reutilization, reuse has inherent difficulties. Our naive question is why component reuse of home appliances seems impossible while that of photocopiers succeeded. This paper clarifies an essential factor for successful reuse; that is, the balance between supply and demand of reusables, and proposes an index named ‘marginal reuse rate,’ which indicates upper limit of reusability. By using this index, reusability of several products is analyzed. The marginal reuse rate indicates that design of lifecycle, in addition to product design, is indispensable for successful reuse.     

Morphology and preferred orientation of Y2O3 film prepared by high-speed laser CVD

Yttria (Y₂O₃) films were prepared at high deposition rates of up to 83 nm/s (300 μm/h) by laser chemical vapor deposition (LCVD) using an Y(dpm)₃ precursor. The effects of deposition conditions, mainly total gas pressure and laser power, on morphology, deposition rate and preferred orientation were studied. Plasma was produced around the substrate over a critical laser power resulting in significant increases in deposition temperature and deposition rate. The high deposition rate (300 μm/h) by LCVD was about 100 to 1000 times as high as those by conventional CVD. The morphology of Y₂O₃ films changed from faceted and columnar structures with high (400) orientation to a columnar structure with high (440) orientation, and finally to a cone-like structure with moderate (440) orientation with increasing total gas pressure (P_tot).