Morphology‐dependent electrocatalytic activity of nanostructured Pt/C particles from hybrid aerosol–colloid process

An optimum nanostructure and pore size of catalyst supports is very important in achieving high catalytic performances. In this instance, we evaluated the effects of various carbon nanostructures on the catalytic performances of carbon‐supported platinum (Pt/C) electrocatalysts experimentally and numerically. The Pt/C catalysts were prepared using a hybrid method involving the preparation of dense, hollow, and porous nanostructured carbon particle via aerosol spray pyrolysis followed by microwave‐assisted Pt deposition. Electrochemical characterization of the catalysts showed that the porous Pt/C catalyst gave the best performance; its electrochemical surface area was much higher, more than twice than those of hollow or dense Pt/C. The effects of pore size on electrocatalysis were also studied. The results showed the importance of a balance between mesopores and macropores for effective catalysis with a high charge transfer rate. A fluid flow model showed that good oxygen transport contributed to the catalytic activity. © 2015 American Institute of Chemical Engineers AIChE J, 62: 440–450, 2016     

Durability of radiation-sterilized polymers III. Oxidation layer determined by chemiluminescence

Chemiluminescence (CL) analysis was used for determining the oxidation layer formed by the irradiation of polypropylene for medical supplies. The depth of the oxidation layer from the surface depended on dose rate and increased with decreasing dose rate. The oxidation occurred remarkably at a region near the surface area of the film where the diffusion of oxygen is more sufficient. On the contrary, there was very little oxidation in the interior portion. The oxidation layers of polypropylene samples irradiated with electron beam showed U-shaped profiles in the cross-section of film as did as a sample irradiated with γ-rays. However, the degree of oxidation by irradiation with electron beam was very small; CL intensity at the surface area was only one-third that for the γ-irradiated samples.     

Regiospecific analysis by ethanolysis of oil with immobilized <Emphasis Type="Italic">Candida antarctica</Emphasis> lipase

A mixture of oil/ethanol (1∶3, w/w) was shaken at 30°C with 4% immobilized Candida antarctica lipase by weight of the reaction mixture. The reaction regiospecifically converted FA at the 1- and 3-positions to FA ethyl esters, and the lipase acted on C₁₄−C₂₄ FA to a similar degree. The content of 2-MAG reached a maximum after 4 h; the content was 28–29 mol% based on the total amount of FA in the reaction mixture at 59–69% ethanolysis. Only 2-MAG were present in the reaction mixture during the first 4 h, and 1(3)-MAG were detected after 7 h. After removal of ethanol from the 4-h reaction mixture by evaporation, 2-MAG were fractionated by silica gel column chromatography. The contents of FA in the 2-MAG obtained by ethanolysis of several oils coincided well with FA compositions at the 2-position, which was analyzed by Grignard degradation. It was shown that ethanolysis of oil with C. antarctica lipase can be applied to analysis of FA composition at the 2-position in TAG.     

Chemical‐Free Approach for Z‐Isomerization of Lycopene in Tomato Powder: Hot Air and Superheated Steam Heating above the Melting Point of Lycopene

Z‐isomers of lycopene exhibit higher bioavailability and antioxidant capacity than those of the all‐E‐isomer. Therefore, it is important to develop an efficient and environmentally friendly procedure for Z‐isomerization. The current methods for Z‐isomerization of (all‐E)‐lycopene use toxic chemicals such as organic solvents and catalysts. This study is aimed to develop a chemical‐free method for Z‐isomerization of (all‐E)‐lycopene in tomato powder by hot air and superheated steam heating. The Z‐isomerization reaction is promoted by heating above the melting point of lycopene. When heated with superheated steam, the thermal decomposition of lycopene is suppressed compared to that when heated with hot air. When tomato powder is heated at 240 °C for 5 min by superheated steam, the total Z‐isomer content and remaining lycopene are 69.0% and 90.7%, respectively, while with hot air heating, the total Z‐isomer content and remaining lycopene are 69.9% and 68.0%, respectively. These results indicate that the thermal Z‐isomerization of lycopene occurs in the molten state and heating in a low oxygen atmosphere suppresses the thermal decomposition of lycopene. Practical Applications: Tomato powder rich in lycopene Z‐isomers is an important ingredient for the food and animal feed industries. Since Z‐isomers of lycopene are more soluble in solvents including ethanol which is a low‐toxicity and environmentally friendly solvent, the efficiency of lycopene extraction with ethanol can be improved by using the Z‐isomer‐rich tomato powder as a raw material. The obtained Z‐isomer‐rich extract has a high added value because the Z‐isomers have higher bioavailability and antioxidant capacity than those of the all‐E‐isomer. In addition, since lycopene Z‐isomers exhibit higher accumulation efficiency and better color improvement in hen egg yolks than those of the all‐E‐isomer, Z‐isomer‐rich tomato powder is an effective animal feed.     

Formation Mechanism and Synthesis of Apatite-Type Structure Ba2+xLa8−x(SiO4)6O2−δ

The formation process of Ba₂La₈(SiO₄)₆O₂ was clarified using thermogravimetry–differential thermal analysis (TG-DTA) and a high-temperature powder X-ray diffraction (HT-XRD) method. Phase changes identified from the HT-XRD data surprisingly corresponded to the weight loss and/or endothermic peaks observed in the TG-DTA curves. Raw material with the composition Ba₂La₈(SiO₄)₆O₂ was completely reacted at 1400°C and produced only an apatite-type compound without a secondary phase. Moreover, the synthesis of Ba_{2+ x} La_{8− x} (SiO₄)₆O_2−δ crystals with x = 0–2 was attempted using a solid-state reaction.     

High-Temperature Active Oxidation of Chemically Vapor-Deposited Silicon Carbide in CO─CO2 Atmosphere

Active oxidation behavior of CVD-SiC in CO─CO₂ atmospheres was investigated using a thermogravimetric technique in the temperature range between 1823 and 1923 K. The gas pressure ratio, P _CO2/ P _CO, was controlled between 10⁻⁴ and 10⁻¹ at 0.1 MPa. Active oxidation rates (mass loss rates) showed maxima at a certain value of P _CO2/ P _CO, ( P _CO2/ P _CO )^*, In a P _CO2/ P _CO region lower than the ( P _CO2/ P _CO)^* a carbon layer was formed on the SiC surface. In a P _CO2/ P _CO region higher than the ( P _CO2/ P _CO)^*, silica particles or a porous silica layer was observed on the SiC surface.     

Fabrication of porous magnesium spinel with directional pores by unidirectional solidification

A porous magnesium spinel (MgAl₂O₄) with directional pores was fabricated by unidirectional solidification in pressurized argon and hydrogen mixed gases. Two different kinds of pores with large directional and small facet shape were formed in the solidified samples. The former pores were dominant in the porous structure. A small amount of free corundum phase was formed in the solidified porous spinel as a secondary phase by vaporization of MgO component during the solidification process. With increasing total gas pressure, the pore size of the solidified samples decreased while no change in the porosity. The porosity and pore size of the samples increased with increasing hydrogen partial pressure. The porosities of the samples fabricated under 10%H₂–90%Ar and 1%H₂–99%Ar mixed gases were 30 and 10%, respectively, and that under Ar atmosphere was very low, non-porous.     

Heat transfer and flow characteristics of flow boiling of CO2‐oil mixtures in horizontal smooth and micro‐fin tubes

Experiments were carried out on the flow pattern, heat transfer, and pressure drop of flow boiling of pure CO₂ and CO₂‐oil mixtures in horizontal smooth and micro‐fin tubes. The smooth tube is a stainless steel tube with an inner diameter of 3.76 mm. The micro‐fin tube is a copper tube with a mean inner diameter of 3.75 mm. The experiments were carried out at mass velocities from 100 to 500 kg/(m²·s), saturation temperature of 10 °C, and the circulation ratio of lubricating oil (PAG) was from 0 to 1.0 mass%. Flow pattern observations mainly showed slug and wavy flow for the smooth tube, but annular flow for the micro‐fin tube. Compared with the flow patterns in the case of pure CO₂, an increase in frequency of slug occurrence in the slug flow region, and a decrease in the quantity of liquid at the top of the tube in the annular flow region were observed in the case of CO₂‐oil mixtures. With pure CO₂, the flow boiling heat transfer was dominated by nucleate boiling in the low vapor quality region, and the heat transfer coefficients for the micro‐fin tube were higher than those of the smooth tube. With CO₂‐oil mixtures, the flow boiling heat transfer was dominated by convective evaporation, especially in the high vapor quality region. In addition, the heat transfer coefficient decreased significantly when the oil circulation ratio was larger than 0.1 mass%. For the pressure drop characteristics, in the case of pure CO₂, the homogeneous flow model agreed with the experimental results within ±30% for the smooth tube. The pressure drops of the micro‐fin tube were 0–70% higher than those predicted with the homogeneous flow model, and the pressure drops increased for the high oil circulation ratio and high vapor quality conditions. The increases in the pressure drops were considered to be due to the increase in the thickness of the oil film and the decrease in the effective flow cross‐sectional area. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20287     

两相流射流的最小半径数值研究

针对大气中水射流的动态特性,使射流形状、特性难以精确预测,提出了判定射流缩流截面的准则,进行了多工况下自由射流非定常两相流数值解析,对射流特别是两相流分界面区域的能量分布及涡度进行了分析,根据VOF法对射流自由表面进行数值预测的结果,获得了射流缩流半径、射流膨胀率等重要参数,并对自由射流尺度效应进行了探讨。     

Contrasting effects of water-soluble and water-insoluble dietary fibers on bile acid conjugation and taurine metabolism in the rat

The effect of the type of dietary fiber on the bile acid and taurine metabolism was examined in rats. Diets containing 10% of various water-soluble fibers (citrus pectin, konjak mannan, guar gum) as compared to a fiber-free diet increased biliary excretion of total bile acids. In contrast, water-insoluble dietary fibers (cellulose, corn bran, chitin; 10% in the diets) as well as cholestyramine (5% in the diet) considerably, decreased bile acid excretion. Water-soluble dietary fibermediated increases in bile acid excretion were totally attributable to increases in glycine-conjugates. Thus, these fibers greatly increased by the bile acid glycine-to-taurine ratio (G/T). Excretio of glycine conjugates decreased more than that of taurine conjugates in rats fed various water-insoluble dietary fibers. As a results, G/T in rats fed water-insoluble fibers was significantly lowered as compared to G/T in animals fed a fiber-free diet. Cholestyramine did not affect the G/T ratio of bile acids. Fecal bile acid excretion and the activities of hepatic cholesterol 7α-hydroxylase (EC 1.14.13.17) in rats fed various water-soluble dietary fibers approximately doubled as compared to the respective values for rats fed a fiber-free diet. Whereas cholestyramine greatly increased these parameters, water-insoluble fibers did not significantly affect them. Various water-soluble fibers decreased hepatic concentration and urinary excretion of taurine as well as the activity of hepatic cysteine dioxygenase (EC 1.13.11.20). In contrast, water-insoluble fibers considerably increased hepatic taurine concentrations and enzyme activities. The parameters for taurine metabolism were unaffected by cholestyramine. It was suggested that the types of dietary fiber affected hepatic taurine synthesis and thus modified bile acid glycine/taurine ratios.