Tuning of tunnel resistance of nanogaps by field-emission-induced electromigration using current source mode

A newly investigated technique for the tuning of the tunnel resistance of nanogaps using electromigration method induced by a field emission current is presented to reduce the power consumption during the process. The method is called "activation" and is demonstrated with a current source. Planar-type initial nanogaps of Ni separated by 20-80 nm were defined on SiO2/Si substrates via electron-beam lithography and the lift-off process. Then, a bias current was applied to the initial nanogaps at room temperature, using a current source. The applied current was slowly ramped up until it reached the preset value. As a result, the process time of the current-source-based activation was 16 times shorter than activation using a voltage source. Furthermore, the tunnel resistance of the nanogaps was reduced from 100 T ohms to 70 M ohms by increasing preset current I(s) from 1 nA to 3.5 microA. Regarding the average power required for current-source-based activation, it can be successfully suppressed compared with that of voltage-source-based activation. These results imply that the current source directly and precisely tunes the field emission current passing through the nanogaps, and effectively causes the migration of atoms across the nanogaps, resulting in the successful control of the tunnel resistance of the nanogaps.     

High reliability optical splitters composed of silica-based planarlightwave circuits

The environmental and mechanical reliability of a planar lightwave circuit (PLC)-type optical splitter modules is investigated with reference to the Bellcore requirements. The module is composed of Y-branching silica-based waveguides on Si connected to optical fiber with UV-curable adhesives and is packaged in a metal case which is filled with humidity-resistant resin. High optical performance such as low loss, low reflection, and thermal stability are obtained through the use of this fiber connection technique. Ten reliability tests including long-term environmental and mechanical tests were carried out for more than ten PLC splitter modules. Under one of the most severe sets of conditions (75°C and 90% RH), all the 19 samples we tested were stable for more than 5000 hours. Other tests confirmed that the PLC splitters offer long-term stability and that their optical characteristics have sufficient mechanical strength. These results indicate that the PLC splitters can be used for practical applications     

Determination of the heat change in solvent extraction of metals. The extraction of zinc (II) from hydrochloric acid solutions by high molecular weight amines in various organic solvents

The heat change associated with the uptake of zinc (II) has been examined by using a twin type isoperibol calorimeter in the extraction of zinc (II) from hydrochloric acid solutions by trioctylamine hydrochloride (TOAHCl) and trioctylmethyl-ammonium chloride (TOMAC) in various organic solvents such as benzene, chlorobenzene, o-dichlorobenzene, toluene, m-xylene, nitrobenzene, carbon tetrachloride and 1, 2-dichloroethane. It was found that the dependence of apparent molar heat change (the value of the heat change detected with regard to the concentration of zinc (II) reacted) on the aqueous chloride concentration could be attributed to the change in the distribution of zinc (II) chloride species in the aqueous phase. Taking account of this fact, variable Y, which constitutes the sum of the change in enthalpies for the relevant steps in the extraction of zinc (II), except the transformation of ZnCl_j^(2-j)+ to ZnCl₄^2-, in the aqueous phase, is introduced. From the values of Y obtained, it is concluded that in the extraction by TOMAC, Y correlates with the solubility parameter of diluent, suggesting that the organic phases may be regarded as regular solutions, while in the extraction by TOAHCl, no clear-cut relation holds between Y and the physico-chemical constants of the diluent such as dipole moment, dielectric constant and solubility parameters.     

Experimental study on growth of epiphysial plate: free graft in rabbits

The growth potential of a free graft of an epiphysial plate was investigated in rabbits. Two epiphysial plate grafts were harvested from each iliac crest. One was grafted to the head (onto bone) and the other to the ear (onto cartilage). Both of the epiphysial plates enlarged to a maximum height of 1.4 cm and became similar to iliac crests. Enchondral ossification was observed up till approximately 28 weeks of age. We conclude that an epiphysial plate has growth potential after free heterotopic transplantation.     

A wide-FSR waveguide double-ring resonator for optical FDMtransmission systems

A wide free-spectral-range (FSR) waveguide double-ring resonator (DRR) is investigated for use in optical frequency-division multiplexing (OFDM) transmission systems. It consists of two ring resonators with different radii and three directional couplers. The FSR is determined by the least common multiple of the FSRs of the two ring resonators. In order to determine the parameters of the DRR, transmission equations of the DRR, which have different radii, are derived by using the scattering matrix. The dependence of the transmittance characteristics of the DRR on the amplitude coupling coefficients of directional couplers and on the propagation loss of the ring waveguides is studied. The design guidelines for OFDM transmission systems are described     

Factors affecting the design of optical FDM informationdistribution systems

Major factors affecting optical frequency division multiplexing (FDM) distribution system design are described. In particular, multiplexing/distribution configuration and channel-selection methods are compared from the viewpoint of the number of channels, the number of subscribers, and the transmission distance. The applicability of optical fiber amplifiers to the optical FDM information-distribution network is also discussed. The experimental results of a 5 GHz spaced 16-channel FDM distribution/transmission at 622 Mb/s, using a waveguide frequency-selection switch (tunable filter) and a multicarrier frequency-stabilization technique, are also discussed     

Evaluation of the implant type tissue-engineered cartilage by scanning acoustic microscopy

The tissue-engineered cartilages after implantation were nonuniform tissues which were mingling with biodegradable polymers, regeneration cartilage and others. It is a hard task to evaluate the biodegradation of polymers or the maturation of regenerated tissues in the transplants by the conventional examination. Otherwise, scanning acoustic microscopy (SAM) system specially developed to measure the tissue acoustic properties at a microscopic level. In this study, we examined acoustic properties of the tissue-engineered cartilage using SAM, and discuss the usefulness of this devise in the field of tissue engineering. We administered chondrocytes/atelocollagen mixture into the scaffolds of various polymers, and transplanted the constructs in the subcutaneous areas of nude mice for 2 months. We harvested them and examined the sound speed and the attenuation in the section of each construct by the SAM. As the results, images mapping the sound speed exhibited homogenous patterns mainly colored in blue, in all the tissue-engineered cartilage constructs. Contrarily, the images of the attenuation by SAM showed the variation of color ranged between blue and red. The low attenuation area colored in red, which meant hard materials, were corresponding to the polymer remnant in the toluidine blue images. The localizations of blue were almost similar with the metachromatic areas in the histology. In conclusion, the SAM is regarded as a useful tool to provide the information on acoustic properties and their localizations in the transplants that consist of heterogeneous tissues with various components.     

Molecular dynamics investigation of the fracture mechanism of a glass-ceramic containing cleavable crystals

In this study on a novel glass-ceramic containing hexagonal CaAl₂Si₂O₈ crystals embedded in a SiO₂–Al₂O₃–CaO glass, we used molecular dynamics simulations to unravel the toughening mechanism of the partially crystallized composite material. The crystalline phase is composed of alternate layers of SiO₄/AlO₄ tetrahedra and calcium ions. After careful modeling of crystals embedded in the glass matrix, we conducted crack propagation simulations using single-notched models. We found that: (a) when a crack propagates parallel to the cleavable calcium layer, the glass-ceramic breaks in a brittle way since the crack passes through the fragile interlayer promptly, (b) the stiffer SiO₄/AlO₄ oxide layer can inhibit crack propagation, and the crack is thus deflected to the interface between the crystal and the glass matrix; and (c) a calcium layer present between the glass matrix and the edge of the CaAl₂Si₂O₈ crystal is more fragile than those inside the crystal, indicating that cracks prefer to travel along the glass-crystal interface. These theoretical simulations successfully demonstrated that the anisotropy and the fragile feature of the crystals lead to microcrack toughening of the glass-ceramic. In addition, we discuss deformation anisotropy in the microscale by constructing a larger model that includes randomly orientated multiple CaAl₂Si₂O₈ crystals.     

Attempt to extract features and classify subjective poor physical conditions in facial images using deep metric learning

Artificial Life and Robotics - With the spread of COVID-19, the need for remote detection of physical conditions is increasing, for example, there are several situations wherein the body...     

Laser-trimming adjustment of waveguide birefringence in optical FDMcomponents

Laser trimming of amorphous-silicon stress-applying films deposited on silica-based single-mode waveguides is demonstrated for controlling waveguide birefringence. Successful applications to polarization-insensitive operation of an optical ring resonator and a Mach-Zehnder interferometer are presented. A phase difference of less than π/100 between TE and TM modes has been attained. It is noted that this laser trimming method can also be applicable to other material devices such as LiNbO₃ and yttrium-aluminum-garnet (YAG), where waveguide birefringence control is a crucial factor in achieving the practical performance of the device