Surface tension and contact angle of herbicide solutions affected by surfactants

Contact angle and surface tension were measured for distilled and hard water solutions of adjuvants, Ortho X-77, Span-20, Sterox-NJ. Surfactant-WK, Triton B-1956, Triton X-114, Tween-20, and Sun Oil 11E. The same parameters were measured for suspensions of atrazine [2-chloro-4-(ethylamino)-6-(isopropylamino)-s-triazine] and ametryne [2-(ethylamino)-4-(isopropylamino)-6-(methylthio)-s-triazine] with and without each adjuvant. All adjuvants reduced surface tension and contact angle of distilled water; Surfactant-WK was most effective and Tween-20 was least effective. Increasing concentration of surfactants from 0 to 0.1% (v/v) gave progressive reduction in surface tension and contact angle while higher concentrations, 0.1 to 2.0% (v/v), had no further effect. Surfactant-WK at 0.1% (v/v) in distilled water reduced the surfact tension from 72.8 dynes/cm to 27 dynes/cm and contact angle from 110° to 41°. An additional increase in Surfactant-WK concentration from 0.1% (v/v) to 2% (v/v) did not further reduce surface tension and contact angle. Sun Oil 11E was identical in behavior except that it was less effective than the surfactants. Water hardness up to 1,000 ppm as Ca ions did not affect surface tension and contact angle in surfactant solutions. An aqueous solution of atrazine had a higher surface tension and contact angle than ametryne in the absence of surfactants. However, these differences were not observed when surfactants were added to either herbicide.     

An Experimental Study to Evaluate the Effect of Ambient Temperature during Manual Lifting and Design of Optimal Task Parameters

In the present study, the effect of lifting task parameters on the heart rate and oxygen uptake of workers during manual lifting tasks in different ambient conditions was evaluated. The experiments conducted in two different temperature conditions showed a significantly higher oxygen uptake and heart rate in colder conditions as compared to warmer conditions. Three other factors, namely, load, lifting frequency, and vertical distance were found to significant affect the responses. Various combinations of significant factors were used to calculate oxygen uptake and heart rate. These were then compared with the safe limits as per the maximum aerobic capacity of workers. Based on these comparisons, the safe combinations were identified that can be used to design lifting tasks in varied ambient conditions. The study further concluded that lifting tasks performed in winter should have different relaxation or fatigue allowances built into the cycle time of the task to compensate for higher exertion. © 2011 Wiley Periodicals, Inc.     

Heterogeneous networking

In this article, security challenges related to a mobile heterogeneous networking environment, and the general access patterns are discussed. A novel, unified networking architecture that enables secure heterogeneous networking, both in terms of networks and user devices is discussed. A comprehensive security framework providing a generalized authentication scheme using the Extensible Authentication Protocol (EAP) is then presented, by taking into account existing methods for secure network and device access.     

Lime-induced iron chlorosis in sugarcane

Lime-induced chlorosis is a potential problem on most calcareous soils particularly in arid and semi-arid climates affecting most of the plants grown on them. Bicarbonates, phosphates, calcium, iron inactivation in plant tissue and organic anions have been held responsible as the mechanism leading to the disorder which is still not fully understood, and there is a lack of agreement as to the primary factor responsible for lime-induced chlorosis. To date, no hypothesis has adequately explained why chlorosis occurs on some high lime soils and not on others. Likewise, the nutrient ratios, K/Ca, P/Fe and Fe/Mn considered as diagnostic criteria for lime-induced chlorosis, have shown inconsistency. The presence of calcium carbonate, bicarbonate, calcium and imbalance of nutrient cations in the growth medium, injudicious addition of phosphates, quality of irrigation water, and other soil and plant factors have been held responsible for the disorder. Amelioration of lime-induced chlorosis by (i) acidification of calcareous soils, (ii) use of iron salts, (iii) use of synthetic iron chelates, and (iv) by management practices including the selection and development of varieties resistant to lime-induced iron chlorosis, is discussed. Suggestions for future research work are made.     

Formation of Nanocrystalline Calcia by the Decomposition of Calcite

Formation of nanocrystalline calcia from calcite has been studied in situ via transmission electron microscopy. The crystallographic transformation occurred via two mechanisms: the first is by distortion of the cleaved rhombohedron of calcite, formed by {104} planes in hexagonal coordinates, into a cube. This produced a microstructure of oriented, elongated nanocrystals of calcia with planar boundaries. In the second mechanism, the micrometer-sized parent calcite particles broke up into nano-sized grains as the decomposition began, leading to irregularly shaped, randomly oriented nanocrystals of calcia.     

Studies on chemical resistance of polyesters

Chlorendic anhydride based polyester ( I ,) tetrachlorophthalic anhydride based polyester ( II ), dibromoneopentyl glycol based polyester ( III ,) general purpose polyester ( IV ,) blend of dibromoneopentyl glycol based polyester with general purpose polyester ( V ,) chlorendic anhydride and dibromoneopentyl glycol based polyester ( VI ), and a blend of chlorendic anhydride based polyester and dibromoneopentyl glycol based polyester ( VII ) were prepared and their chemical resistance and moisture absorption studied in various reagents, acid, alkali, and water, at 25 and 65°C. It is found that the polyester ( III ) is the least affected in the presence of the acids. In 20% NaOH, there was a decrease in weight for all polyesters at both the temperatures compared to the control except the polyester ( VII ). Increase in weight of all the polyesters was observed during the absorption of moisture both at 25 and 65°C. The increase was higher at higher temperature. Polyester ( III ) thus shows the least absorption of moisture.     

Thermal stability of PVC/chlororubber-20-graft polyblend–styrene–acrylonitrile blends. I

Thermal stability of PVC blends with chlororubber-20-graft polyblend-styrene-acrylonitrile [CR-20gp-SAN (2:1)] was studied by HCI evolution techniques and thermogravimetry under isothermal condition. The thermal stability of PVC/CR-20gp-SAN (2:1) blends has been compared with those of PVC/CR-20 and PVC/KM-365B blends. It has been observed that the thermal stability of modified PVC is less than that of unmodified PVC. The CR-20gp-SAN (2:1) modified PVC blends were found to be more stable than PVC/CR-20 blends but less stable than PVC/KM-365B blends. The rate of degradation in PVC blends were observed to be unaffected by the concentration of the modifiers, but the PVC/KM-365B blends were found to be degrading slower in comparison with PVC/CR-20 and PVC/CR-20gp-SAN (2:1) blends. The rate of degradation for PVC/CR-20 blends at lower concentrations (<10%) of modifiers is almost equal to that of PVC/CR-20-gp-SAN (2:1) blends, but more at higher concentrations of modifiers (>10%). The experimental results have been explained on the basis of the chemical nature of the modifiers and their miscibility with PVC.     

Note: The Use of Triallyl Cyanurate in Bonding PVC Plastisols to Steel

The use of diallyl phthalate as the basis for a non-extractable plasticizer for poly(vinylchloride) (PVC) is well-known. Used in conjunction with a primary plasticizer and a polymerization initiator, a plastisol coating for steel can be formulated which is oil or grease tolerant and can also be used for bonding some structural steel parts if the area is relatively large compared with the load to be applied. Defrayne and Twiss¹ describe the bonding of automobile hood assemblies by vinyl plastisol adhesives and Schneberger² emphasizes their use in the automobile industry though neither article gives the formulations employed. Commercial formulations giving pull-off strengths of the order of 1 to 4 MN. m^-2 always incorporate a proportion of a phenolformaldehyde resin or even an epoxy, but sound-deadening and other coatings of steel do not necessarily need this reinforcement. Phillips and Longworth³ particularly studied the use of diallylphthalate (DAP) as a polymerizable plasticizer and the consequent improvement in adhesion to mild steel. Sherlock⁴ used a simple formulation without additives when investigating the effect of surface cleaning and conversion coatings (oxides and phosphates). It was suggested that, as outlined below, improved adhesion would be expected if a small proportion of triallyl cyanurate (TAC) were added to the polymerizable plasticizer. This paper shows this expectation to be achieved although the proportion of the more expensive TAC needed for substantial increase in bond strength is greater than was hoped.     

A free space frequency‐time‐domain technique for electromagnetic characterization of materials using reflection‐based measurement

In this report, a free space frequency‐time‐domain technique is presented for characterizing the electrical properties and thickness of the sample using multiple reflections and fabry‐perot resonance phenomenon. The retrieval of constitutive electromagnetic parameters of the sample has been carried out by comparing the measured reflection coefficient data from the sample at two different incident angles. The relative permittivity as well as relative permeability along with the thickness of different samples viz., beryllia, silicon, and plexiglass have been evaluated with high accuracy in the frequency range 1 to 15 GHz. The method is also experimentally validated by successfully reconstructing the unknown material properties of two different samples. The unique advantage of this method lies in non‐requirement of any prior knowledge of the sample's thickness for measuring the complex relative dielectric constant as well as relative permeability of the sample. To determine the electromagnetic properties of the sample, the sole knowledge of reflection coefficient data are needed. Moreover, the method does not involve any additional measurement for the reference calibration. The simple, cost‐effective proposed scheme is quite useful in many applications like accurate determination of signal strength in indoor wireless communication, through wall imaging, food industry, and so on.     

Liver disorder detection using variable- neighbor weighted fuzzy K nearest neighbor approach

The human liver disorder is a genetic problem due to the habituality of alcohol or effect by the virus. It can lead to liver failure or liver cancer, if not been detected in initial stage. The aim of the proposed method is to detect the liver disorder in initial stage using liver function test dataset. The problem with many real-world datasets including liver disease diagnosis data is class imbalanced. The word imbalance refers to the conditions that the number of observations belongs to one class having more or less than the other class(es). Traditional K- Nearest Neighbor (KNN) or Fuzzy KNN classifier does not work well on the imbalanced dataset because they treat the neighbor equally. The weighted variant of Fuzzy KNN assign a large weight for the neighbor belongs to the minority class data and relatively small weight for the neighbor belongs to the majority class to resolve the issues with data imbalance. In this paper, Variable- Neighbor Weighted Fuzzy K Nearest Neighbor Approach (Variable-NWFKNN) is proposed, which is an improved variant of Fuzzy-NWKNN. The proposed Variable-NWFKNN method is implemented on three real-world imbalance liver function test datasets BUPA, ILPD from UCI and MPRLPD. The Variable-NWFKNN is compared with existing NWKNN and Fuzzy-NWKKNN methods and found accuracy 73.91% (BUPA Dataset), 77.59% (ILPD Dataset) and 87.01% (MPRLPD Dataset). Further, TL_RUS method is used for preprocessing and it improved the accuracy as 78.46% (BUPA Dataset), 78.46% (ILPD Dataset) and 95.79% (MPRLPD Dataset).