Distributed hybrid P2P networking systems

Peer-to-Peer Networking and Applications -     

寒冷地区某既有办公建筑围护结构优化改造研究

既有公共建筑能耗中,围护结构节能潜力巨大。以兰州某既有办公建筑为例,采用DeST-C软件模拟围护结构不同材料厚度、窗型,得出系列负荷,通过对数据分析、比较,得出如下结论:外墙外保温适宜材料为50mm的挤塑板,最大热负荷节能率为45.66%;屋面适宜保温材料为65mm的挤塑板,最大热负荷节能率为4.25%;外窗各个朝向全部更换玻璃,推荐选用内张膜中空玻璃(双膜),最大热负荷节能率为7.36%;单独更换南向外窗材料,推荐选用真空镀膜复合中空玻璃,最大热负荷节能率为1.78%。     

Multiply Charged Conjugated Polyelectrolytes as a Multifunctional Interlayer for Efficient and Scalable Perovskite Solar Cells

A series of anionic conjugated polyelectrolytes (CPEs) is synthesized based on poly(fluorene-co-phenylene) by varying the side-chain ionic density from two to six per repeat units (MPS2-TMA, MPS4-TMA, and MPS6-TMA). The effect of MPS2, 4, 6-TMA as interlayers on top of a hole-extraction layer of poly(bis(4-phenyl)-2,4,6-trimethylphenylamine (PTAA) is investigated in inverted perovskite solar cells (PeSCs). Owing to the improved wettability of perovskites on hydrophobic PTAA with the CPEs, the PeSCs with CPE interlayers demonstrate a significantly enhanced device performance, with negligible device-to-device dependence relative to the reference PeSC without CPEs. By increasing the ionic density in the MPS-TMA interlayers, the wetting, interfacial defect passivation, and crystal growth of the perovskites are significantly improved without increasing the series resistance of the PeSCs. In particular, the open-circuit voltage increases from 1.06 V for the PeSC with MPS2-TMA to 1.11 V for the PeSC with MPS6-TMA. The trap densities of the PeSCs with MPS2,4,6-TMA are further analyzed using frequency-dependent capacitance measurements. Finally, a large-area (1 cm²) PeSC is successfully fabricated with MPS6-TMA, showing a power conversion efficiency of 18.38% with negligible hysteresis and a stable power output under light soaking for 60 s.     

Core–shell NTC materials with low thermal constant and high resistivity for wide-temperature thermistor ceramics

Core–shell structures have been proposed to improve the electrical properties of negative-temperature coefficient (NTC) thermistor ceramics. In this work, Al₂O₃-modified Co_1.5Mn_1.2Ni_0.3O₄ NTC thermistor ceramics with adjustable electrical properties were prepared through citrate-chelation followed by conventional sintering. Co_1.5Mn_1.2Ni_0.3O₄ powder was coated with a thin Al₂O₃ shell layer to form a core–shell structure. Resistivity (ρ) increased rapidly with increasing thickness of the Al₂O₃ layer, and the thermal constant (B) varied moderately between 3706 and 3846 K. In particular, Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ ceramic with 0.08 wt% Al₂O₃ showed the increase of ρ double, and the change in its B was less than 140 K. The Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics showed high stability, and their grain size was relatively uniform due to the protection offered by the shell. The aging coefficient of the ceramic was less than 0.2% after aging for 500 hours at 125°C. Taken together, the results indicate that as-prepared Co_1.5Mn_1.2Ni_0.3O₄@Al₂O₃ NTC ceramics with a core–shell structure may be promising candidates for application as wide-temperature NTC thermistor ceramics.     

基于滑模的运载器主动段俯仰通道姿控系统设计

与传统比例-积分-微分（PID）控制方法相比，滑模控制（SMC）方法可以比较容易地将不确定性纳入控制器设计中，从而增强系统的鲁棒性。探索了SMC技术在运载器主动段姿态控制中的工程应用，首先通过分析基于趋近律的SMC系统，提出了降低不连续切换项系数的需求，然后研究了基于干扰上界的SMC方法。三通道小偏差仿真结果验证了两种方法的控制效果，表明第2种控制器的鲁棒性更好，稳态误差小，同时发动机喷管摆角需求较小。