Quantitative measurement of hard x-ray spectra for high intensity laser produced plasma

X-ray line spectra ranging from 17 to 77 keV were quantitatively measured with a Laue spectrometer, composed of a cylindrically curved crystal and a detector. Either a visible CCD detector coupled with a CsI phosphor screen or an imaging plate can be chosen, depending on the signal intensities and exposure times. The absolute sensitivity of the spectrometer system was calibrated using pre-characterized laser-produced x-ray sources and radioisotopes. The integrated reflectivity for the crystal is in good agreement with predictions by an open code for x-ray diffraction. The energy transfer efficiency from incident laser beams to hot electrons, as the energy transfer agency for specific x-ray line emissions, is derived as a consequence of this work.     

Preparation of Lead Lanthanum Zirconate Titanate (PLZT, (Pb,La)(Zr,Ti)O3) Fibers by Sol-Gel Method

Lead lanthanum zirconate titanate (PLZT, (Pb,La)(Zr,-Ti)O₃) ceramic fibers were prepared by the sol-gel method from a solution of lead acetate trihydrate, lanthanum isopropoxide, zirconium n -propoxide, and titanium isopropoxide that contained 2-methoxyethanol as the solvent. The sols obtained from the solution were concentrated at 156°-174°C for 2 h. Concentration at higher temperatures resulted in more-viscous sols of higher specific gravities. The concentration resulted in the formation of spinnable sols, which had viscosities >10⁵ mPas and exhibited Newtonian flow properties. These spinnable sols were formed to be so stable that no change in viscosity and spinnability was observed for more than three months when stored in a sealed container at room temperature. Gel-to-ceramic fiber conversion was investigated by means of X-ray diffractometry, infrared spectroscopy, and thermal analysis. Single-phase perovskite PLZT ceramic fibers 5-200 μm in diameter and >20 cm in length were obtained. Scanning electron microscopy (SEM) observation and Brunauer-Emmett-Teller (BET) measurement showed that heat treatment of the fibers at a lower rate resulted in the formation of fibers of denser microstructure. Although the SEM image of the cross section of the fibers revealed a relatively dense microstructure and a laser beam could be transmitted through a fiber 6 mm in length, BET measurement of the fibers indicated that the fibers had more than a few percent of open porosities, and scattering of light was observed in the laser-beam guiding test.     

Photoelectrochemical properties of sol–gel-derived Ti1−xVxO2 solid solution film photoelectrodes

Ti_1−xV_xO₂ solid solution film photoelectrodes were prepared by the dip-coating sol–gel method. X-ray diffraction and X-ray photoelectron spectroscopy were employed to ensure the formation of the solid solution and their composition. Obvious photoresponses were observed in the visible region for the solid solution film electrodes with x0.05 and the red shift of the photoresponse was enhanced with increasing x. Moreover, the solid solution film electrodes were found to be photoelectrochemically stable. However, the onset potential of photocurrent shifted positively with increasing x. Band model of the solid solution was suggested to explain the effects of the vanadium incorporation on the photoelectrochemical properties.     

Synthesis of Er-doped ZnO nanoparticle/organic hybrid from metal-organics

An Er-doped ZnO nanoparticle/organic hybrid was synthesized in situ from zinc acrylate (ZA) and erbium acetate (EA) using methylhydrazine. Nano-sized Er-doped ZnO particles were formed in an organic matrix by hydrolysis and polymerization of ZA–EA at 80 °C. The crystallinity of the Er-doped ZnO particles in the hybrid was dependent upon the hydrolysis temperature and water amount. Analysis by transmission electron microscopy and energy dispersive X-ray analyzer revealed that crystalline ZnO nanoparticles doped with Er were dispersed in the organic matrix. The hybrid film sandwiched between fused silica plates was highly transparent. The Er-doped ZnO particle/organic hybrid showed a photoluminescence peak at 0.81 eV (1.54 μm) attributed to the transition of Er³⁺ ions.     

Measurement of Flow Stress in Supercooled Austenite for High Hardenability Steel

In this article, the isothermal flow stress in supercooled austenite was measured for a high hardenability steel. Supercooled austenite forms at the nonequilibrium phase and changes into other phases within a short time. It was confirmed that conventional tensile tests, which require maintaining a constant temperature before stretching, cannot accurately measure the flow stress in supercooled austenite. Therefore, a new tensile test named “the continuous cooling tensile test” was developed. In this test, stretching is conducted during continuous cooling. In the continuous cooling tensile test, the flow stress between 673 K and 973 K (400 °C and 700 °C) was measured. Microscopic observations of the continuous cooling test results verified that the microstructures were supercooled austenite.     

Lack of evidence for the transmission of JC polyomavirus between human populations

Human polyomavirus JC virus (JCV), the causative agent of progressive multifocal leukoencephalopathy, is ubiquitous in humans, infecting children asymptomatically then persisting in renal tissue. Since JCV DNA can readily be detected from urine, it should be a useful tool with which to study the mode of virus transmission in humans. Based on this notion, we examined the extent to which JCV was transmitted from the American to Japanese populations in Okinawa Island, Japan. (A population of about 50 000 American soldiers and families have been stationed in Okinawa since 1945.) Four JCV types (A to D) were identified in American populations in U.S.A., whereas only type B was prevalent in elder Japanese in Okinawa who had reached adulthood by 1945. Thus, types A, C, and D served as indicators of the transmission of JCV from American to Japanese populations. We then examined whether types A, C, and D were detectable in Japanese in Okinawa aged 30-50 years who may have been in contact with Americans during childhood. However, all the 125 isolates from the younger Japanese population were type B without exception. From this finding, we concluded that JCV is rarely transmitted between human populations.     

Synthesis of polycrystalline alumina-zirconia fibre using chelated aluminium-zirconium precursor

Polycrystalline alumina-zirconia fibres were successfully synthesized by pyrolysis of preceramic fibres formed from mixed aluminium-zirconium chelate compounds. Ethyl 3-oxobutanoatodiisopropoxyaluminium (EOPA) was reacted with zirconium tetrabutoxide (TBZ) in the presence of glacial acetic acid yielding a polymeric product. The infrared absorptions from 500–625 cm^–1 due to Al-O and Zr-O bonds changed from sharp to coalesced bands by treatment with acetic acid. The signal at 40 p.p.m. in the ²⁷Al spectra of EOPA-TBZ increased in intensity on treating with acetic acid. The viscosity of the polymeric product increased as the amount of acetic acid increased. The viscosity of the precursor decreased on increasing the measurement temperature from 60 °C to 75 °C. The precursor polymer pyrolysed at 800 °C in air showed a broad X-ray diffraction of -alumina, and crystallized in a mixture of -alumina and tetragonal zirconia at 1000 °C. The median diameter of tetragonal zirconia in the -alumina matrix was 33 nm, when EOPA-TBZ (Al/Zr=9/1) was heat treated at 1300 °C for 1 h. The precursor fibres were pyrolysed at 1300 °C to yield fine-grained fibres of -alumina including tetragonal zirconia, which was confirmed by Raman microprobe spectroscopy.