Effect of some BED blends on the equivalence ratio, exhaust oxygen fraction and water and oil temperature of a diesel engine

Nowadays, natural-based oxygenated fuels, especially biodiesel and ethanol, have been considered as substitutes for fossil fuels. Because of relatively lower energy content of oxygenated fuels, it is necessary to blend them with fossil ones. In this research, authors conducted an investigation on some BED blends to determine and compare their effects on equivalence ratio, exhaust oxygen fraction and water and oil temperature in a diesel engine. For this purpose, 18 different blendes of ethanol and biodiesel with net diesel fuel were tested in a MT4-244 engine¹ considering two engine speeds in full load condition. In almost all samples the equivalence ratio decreased with increasing of biodiesel and ethanol percents. Exhaust oxygen fraction in all of samples increased with increasing of biodiesel and ethanol percents, whereas the engine water and oil temperatures slightly reduced.     

Preparation,FTIR spectroscopic characterization and isothermal stability of differently doped conductive fibers based on polyaniline and polyacrylonitrile

Conductive fibers based on polyaniline (PANI) and polyacrylonitrile (PAN) were obtained by stirring with magnetic bar. This research was conducted to investigate conducting fibers of polyaniline:polyacrylonitrile (PANI:PAN) composite with different weight ratios of aniline in PAN matrix. The fibers were prepared by stirring process. The best conductivity behavior of the fibers was obtained with 5 mL of aniline. The fibers obtained were characterized using Fourier-transform infrared spectra (FTIR), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). The variation of electrical conductivity with different type doping agents (HCl, H₂SO₄ and HClO₄) and the stability in terms of DC electrical conductivity retention was studied in an oxidative environment by isothermal characteristics.     

The effect of pH and calcium ion on rheological behaviour of β‐lactoglobulin‐basil seed gum mixed gels

Effect of pH (4.5–7.5) and Ca²⁺ (0.01–0.5 m ) on gelation of single and mixed systems of 10% β‐lactoglobulin (BLG) and 1% basil seed gum (BSG) was investigated. The gelling point of BLG and BSG gels was strongly pH‐dependent, and stiffer gels formed at higher pH. The BLG gels were formed upon heating to 90 °C and reinforced on cooling to 20 °C; however, the gelation of BSG occurred at temperatures below 70 °C. By increasing Ca²⁺ concentration, storage modulus of BLG and BSG gels were increased, although pH had a greater effect than Ca²⁺. In contrast, mixed systems showed two distinct types of behaviour: BLG gel formation and BSG network, suggesting that phase‐separated gels were formed. In addition, higher strength was obtained for BLG‐BSG mixture at higher Ca²⁺ concentration.     

Performance and thermo-economic assessments of geothermal district heating system: A case study in Afyon,Turkey

In this study energy, exergy and exergoeconomic analysis of the Afyon geothermal district heating system (AGDHS) in Afyon, Turkey is performed through thermodynamic performances and thermo-economic assessments. In the analysis, actual system data are used to assess the district heating system performance, energy and exergy efficiencies, exergy losses and loss cost rates. Energy and exergy losses throughout the AGDHS are quantified and illustrated in the flow diagram. The energy and exergy efficiencies of the overall system are found to be 37.59% and 47.54%, respectively. The largest exergy loss occurs in the heat exchangers with 14.59% and then in the reinjection wells with 14.09%. Besides, thermo-economic evaluations of the AGDHS are given in table. Energy and exergy loss rates for the AGDHS are estimated to be 5.36 kW/$ and 0.2  kW/$, respectively.     

Technical and economic assessment of photovoltaic-driven desalination systems

Solar desalination systems are approaching technical and cost viability for producing fresh-water, a commodity of equal importance to energy in many arid and coastal regions worldwide. Solar photovoltaics (PV) represent an ideal, clean alternative to fossil fuels, especially for remote communities such as grid-limited villages or isolated islands. These applications for water production in remote areas are the first to be nearing cost-competitiveness due to decreasing PV prices and increasing fossil fuel prices over the last five years. The electricity produced from PV systems for desalination applications can be used for electro-mechanical devices such as pumps or in direct-current (DC) devices. Reverse osmosis (RO) and electrodialysis (ED) desalination units are the most favorable alternatives to be coupled with PV systems. RO usually operates on alternating current (AC) for the pumps, thus requiring a DC/AC inverter. In contrast, electrodialysis uses DC for the electrodes at the cell stack, and hence, it can use the energy supplied from the PV panels with some minor power conditioning. Energy storage is critical and batteries are required for sustained operation. In this paper, we discuss the operational features and system designs of typical PV-RO and PV-ED systems in terms of their suitability and optimization for PV operation. For PV-RO and PV-ED systems, we evaluate their electricity need, capital and operational costs, and fresh-water production costs. We cover ongoing and projected research and development activities, with estimates of their potential economics. We discuss the feasibility of future solar desalination based on expected (or predicted) improvements in technology of the desalination and PV systems. Examples are provided for Middle East and other parts of the World.     

One-pot two-step lipase-catalyzed synthesis of α,ω-thiophene-capped poly(ε-caprolactone) macromonomers and their use in electropolymerization

Macromonomers based on poly(ε-caprolactone) (PCL) with α,ω-thiophene functional end groups were prepared in bulk by enzymatic polymerization using immobilized Candida Antarctica lipase B (Novozym 435) as the catalyst. In the synthesis strategy, 3-thiophenemethanol was used to initiate the enzyme-assisted ring-opening polymerization of ε-caprolactone (ε-CL) to yield PCL with α-thiophene end group (initiation reaction, ThPCL) and then 3-thiopheneacetic acid was added to prepolymerized ε-CL to introduce ω-thiophene functionality in termination step (ThPCLTh). Macromonomers were characterized by ¹H and ¹³C NMR, FTIR, and GPC. Moreover, the obtained macromonomers were employed in electropolymerization experiments and copolymers with thiophene or pyrrole were synthesized through their end thiophene groups. These polymers were characterized by cyclic voltammetry (CV), FTIR, and scanning electron microscopy (SEM). Conductivity measurements were carried out by the four-probe technique.     

HVOF sprayed WC–Co coatings: Microstructure,mechanical properties and friction moment prediction

This study aims at gaining a better understanding of the microstructural features that control the mechanical and the tribological performances of WC–12 wt.% Co coatings under High Velocity Oxygen Fuel (HVOF) spraying conditions. This paper looks at the influences of the HVOF process parameters for WC–12Co material on the microstructural and the tribological behaviours of the coatings. The correlation between the coating microstructure and the wear behaviour is investigated by observing and analysing the microstructure and by studying the friction moment using enhanced statistical tool based on neural computations. According to the experimental and the numerical results, it has been shown that the spray parameters affect the phase composition, hardness and porosity of HVOF sprayed WC–12Co coatings and the correlations with HVOF process parameters are fully predictable in the steady-state regime.     

Techno-economic assessment of gas pressure-based electricity generation (A case study of Iran)

The pipeline gas pressure can be recovered as electricity by installing a turbo-expander in parallel with throttle valves at pressure reduction stations. This paper aims to provide a techno-economic assessment of electricity generation at a gas pressure reduction station. Owing to the gas flow rate of the station, technical assessment showed two installation capacities of 2853 kw (Case I) and 4169 kw (Case II). As a result, NPV and IRR for Case I is calculated €1,669,623.93 and 28.95%; and for Case II, NPV and IRR is €1,393,871.91 and 23.91% respectively. The analysis indicated case I is more profitable than case II.