Use of petrochemical waste in the glass industry

It is suggested that ferrochrome slags used for coloring container glass be replaced by waste materials of the petrochemical industry. The expediency of the use of the waste is shown. Recommendations are given on the use of petrochemical waste for coloring container glass.     

Guard sequence optimization for block transmission over linearfrequency-selective channels

We show that the optimum length-ν guard sequence for block transmission over a linear Gaussian-noise dispersive channel with memory ν is a linear combination of the N information symbols of the block. A closed-form expression for the optimum guard sequence is derived subject to a total average energy constraint on the information and guard symbols. The achievable channel block throughput with the optimum guard sequence is compared with that achievable with two common guard sequence types, namely zero stuffing and cyclic prefix     

Interleukin-4 and -13 inhibit tumor necrosis factor-alpha mRNA translational activation in lipopolysaccharide-induced mouse macrophages

The production of tumor necrosis factor-alpha (TNF-alpha) by lipopolysaccharide (LPS)-stimulated macrophages can be markedly inhibited by the two closely related cytokines, interleukin (IL)-4 and IL-13. To investigate the molecular mechanism of this inhibition, we analyzed the effect of the two cytokines on TNF-alpha production and TNF-alpha mRNA accumulation in the mouse macrophage cell lines RAW 264.7 and J774 stimulated by LPS. Whereas LPS-induced TNF-alpha production is strongly suppressed by both cytokines, TNF-alpha mRNA accumulation is not significantly affected, indicating that IL-4 and IL-13 induce a translational repression of TNF-alpha mRNA. Transfection of reporter gene constructs containing different regions of the TNF-alpha gene revealed that the inhibitory action of IL-4 and IL-13 is mediated by the UA-rich sequence present in the TNF-alpha mRNA 3'-untranslated region.     

Identification and analysis of genes from Streptomyces pristinaespiralis encoding enzymes involved in the biosynthesis of the 4-dimethylamino-L-phenylalanine precursor of pristinamycin I

Dextran has been used as a carrier molecule for the synthesis of monofunctional peptide-dextran conjugates. The immunodetection of such carrier immobilized peptides on ELISA plates was compared to that of peptides adsorbed directly to immunoplates. The main features observed with peptide-dextran conjugates were as follows: only small amounts of peptide (1-2 mg) were necessary for coupling via alpha- or epsilon-amino groups to NaIO4-activated dextran (4 mg); the coupling yield was up to 68%; an amino acid analysis of the conjugate enabled the amount of carrier immobilized peptide to be calculated; an estimated 15-17 peptides were bound per dextran molecule (MW 73,500); using a carbohydrate as carrier reduces the possibility of non-specific interactions because no hydrophobic or ionic sites and no protein-like epitopes exist on the carrier apart from the peptide ligand. It can be assumed that some peptide ligands provide the forces for an interaction with the plate surface whereas other remain free for the interaction with the antibody. Thus, the detection with monoclonal anti-peptide antibodies allowed peptide-dextran conjugates to be used at coating concentrations of 1-3 nM peptide, corresponding to 0.6-2.6 ng peptide-dextran per well. In contrast, concentrations of 150-500 nM were required for coating with peptides. The applicability of monofunctional peptide-dextran conjugates was demonstrated by investigating the titer and specificity of a polyclonal anti-peptide serum developed against human gastrointestinal glutathione peroxidase. The introduction of biotin as a second ligand of the dextran conjugate permitted its capture on streptavidin coated plates. This synthesis of bifunctional peptide-biotin-dextran conjugates opens up additional possibilities for applications.     

Impurity Distribution Behavior in Caprolactam Extraction with Environmentally Benign Mixed Solvents

In a previous study a solvent mixture of heptane containing 40 mass % heptanol was selected as an alternative in the industrial extraction of caprolactam to replace benzene, toluene, or chlorinated hydrocarbons. This work reports the equilibrium distribution ratio of caprolactam and four model impurities of organic nature, namely, cyclohexanone, aniline, n‐methylcaprolactam, and cyclohexane‐carboxamide, comparing the mixed solvents with toluene as a reference. The resulting phase equilibria were interpreted using the equilibrium stage model. Based on these calculations it was found that, compared to toluene, the co‐extracted fraction of cyclohexanone and aniline was higher, that of n‐methylcaprolactam was comparable, and that of cyclohexane‐carboxamide was lower using the mixed solvent. Overall, the mixed solvent reduced the fraction of co‐extracted impurities by almost 10 %.     

Development of heat-and impact-resistant coatings for main pipelines

We have developed composite layered temperature-resistant silicon-organic sandwich-type coatings with thin polyurethane silicon-organic interlayers. We used the following materials as binding components: KO 921 silicon-organic lacquer with addition of éD-20 epoxy resin for prime coat, the same lacquer with addition of PZ 1040 S polyurethane elastomer for thin soft interlayers, and only KO 921 lacquer for thick hard layers. The mineral filler represented a mixture of coal ash and omiacarb in proportion 70 / 30 mass %. We have manufactured and tested laboratory specimens with two hard layers and two interlayers as well as with three hard layers and two thin interlayers. We have established that the developed composite layered coatings exceed, in their basic characteristics, the requirements of the State Standard Committee of Ukraine and foreign normative documents for the rust protection of steel main pipelines. Our coatings possess high impact strength, heightened elasticity and adhesion strength and, as to their electrical insulating characteristics, exceed these requirements by an order of magnitude. We note the complexity of the technology of applying layered composite coatings and the necessity of its improvement. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 42, No. 4, pp. 59–65, July–August, 2006.     

Effect of water inlet velocity on thermal stratification in a mantled hot water storage tank

Thermal stratification in a mantled hot water storage tank is analysed numerically for different water inlet velocities. The aim is to obtain higher thermal stratification and supply hot water for usage as long as possible. Twelve different water inlet velocities to the hot water storage tank are considered. The numerical method is validated by comparing its results against experimental and numerical results from the literature. It turned out that the results obtained from the numerical analysis have shown very good agreements with the results from previous works. As a result, the water temperature in the tank increases with the increase of the water inlet velocities to the mantle but this increment is not proportional. After a period of operation of 7.2 h, which corresponds to the average sunshine duration in Turkey, temperature increments of 6.5 and 35 K have been estimated for the hot water inlet velocities of 0.01 and 0.3 m s^?1, respectively, at a radial distance of 0.1 m and a height of 1 m inside the storage tank. Copyright © 2005 John Wiley & Sons, Ltd.