Investigations on surface composition and microstructure of sintered barium titanate

The paper describes studies on surface atomic composition, microstructure and microarea elemental distribution in sintered undoped as well as donor or acceptor doped polycrystalline barium titanate ceramics. The specimens examined are derived from barium titanate powders synthesized by two different wet chemical procedures namely oxalate precursor route and gel-to-crystallite conversion. The compositional analysis is carried out by backscattering spectrometry (BS) involving 3.05 MeV ¹⁶O(α,α)¹⁶O resonant scattering while investigations on microstructure and microarea elemental distribution are performed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS), respectively. The specimens prepared by either method are monophasic; however, their surface atomic composition, microstructural features as well as electrical characteristics are significantly different. The specimens obtained by oxalate precursor route generally have Ti rich surfaces and exhibit coarse to fine grained microstructure depending on the nature and extent of doping. The Mn-doped specimens exhibit appreciable O deficiency. The specimens prepared by gel to crystallite conversion, in contrast, usually have Ba enriched surfaces and exhibit fine-grained microstructure. EDS measurements show the segregation of acceptors such as Mn, Cu and Zn in the grain boundaries of oxalate precursor derived ceramics. Further, the relative atomic ratio of Ti to Ba at the sites of segregations is higher compared to other locations.     

Effect of Controlled Atmosphere Storage and Chitosan Coating on Quality of Fresh-Cut Jackfruit Bulbs

Fresh-cut jackfruit bulbs were evaluated for quality changes as effect of an additive pretreatment with CaCl₂, ascorbic acid, citric acid, and sodium benzoate followed by chitosan coating. Different types of samples such as pretreated and coated, only pretreated, only coated, and untreated were subjected to controlled atmosphere (CA) storage (3 kPa O₂?+?6 or 3 kPa CO₂; N2 balance) or normal air at 6 °C. CA conditions, pretreatment, as well as chitosan coating in synergy with each other, could significantly minimize the loss in total phenolics and ascorbic acid content of the samples to the levels of around 5% and 17%, respectively, during extended storage up to 50 days. Chitosan coating could also restrict the changes in microbial load. The CA condition of 3 kPa O₂?+?6 kPa CO₂ was found to render higher efficacy in retaining quality attributes of the samples.     

An improved frequent pattern tree: the child structured frequent pattern tree CSFP-tree

Pattern Analysis and Applications - Frequent itemsets are itemsets that occur frequently in a dataset. Frequent itemset mining extracts specific itemsets with supports higher than or equal to a...     

The mitigation of signal integrity issues in coupled MWCNT bundles and a comparison with Cu interconnects

Journal of Computational Electronics - In the nanoscale regime, carbon nanotubes (CNTs) are being considered as a future alternative interconnect material for traditional copper (Cu) wires in...     

Identification of factors that lead to perceived learning improvements for female students

Past research has shown that females have more negative attitudes toward engineering and technology than do males. These negative attitudes may explain the decreasing number of females choosing technical careers. Past studies have shown that a change in learning environments and the methods by which learning takes place might foster a change in this situation. A multimedia case study incorporating a real-world engineering and technical problem faced by a power plant was developed in order to provide a new learning environment for engineering and business students. This research investigates whether the use of this material by female and male students led to differences in perceived higher level cognitive skills and, if so, seeks to identify the factors that cause the difference. The results suggest that when designing new learning environments, it is important for the female students to be challenged and have opportunities both to learn by themselves and to learn from others. These results have implications for teaching programs, such as the provision of opportunities for group learning, especially for female students.     

Dielectric relaxation of conductive carbon black reinforced ethylene‐octene copolymer vulcanizates

The dielectric relaxation behavior of different conducting carbon black‐filled ethylene‐octene copolymer (EOC) vulcanizates prepared by melt‐mixing method has been studied as a function of frequency (100 Hz–5 MHz) over a wide range of temperatures (25–100°C). The effect of filler loading and frequency on AC conductivity, dielectric permittivity, impedance, and dielectric loss tangent (tanδ) has been studied. The nature of variation of the dielectric permittivity with the filler loadings was explained on the basis of interfacial polarization of the filler in the polymer matrix. The effect of filler loading on the real and complex part of the impedance was explained by the relaxation dynamics of the polymer chains in the vicinity of the fillers. The effect of filler and temperature on dielectric loss tangent, dielectric permittivity, AC conductivity, and Nyquist plot was also reported. The bound rubber (BR) value increases with increase in filler loading suggesting the formation of strong interphase, which is correlated with dielectric loss. Thermal activation energy (E_a) was found to be decreasing with the temperature, which follows the Arrhenius relation: τ_b = τ₀ exp(−E_a/K_BT) where τ_b is the relaxation time for the bulk material. From the plot of lnτ_b versus inverse of absolute temperature (1/T), the activation energies (E_a) were found to be 0.37 and 0.44eV, respectively. The percolation threshold was observed with 40 phr carbon black loading. POLYM. COMPOS., 37:342–352, 2016. © 2014 Society of Plastics Engineers     

Insulating and Other Physical Properties of CoO‐Doped Zinc Oxyfluoride‐Borate Glass‐Ceramics

Zinc oxy fluoro borate glasses mixed with different concentrations of CoO (ranging from 0 to 2.0 mol%) are synthesized and subsequently crystallized. The scanning electron microscopy pictures have exhibited crystallinity. Differential scanning calorimetric studies have indicated that the prepared samples consist of multiple crystal phases. The X‐ray diffraction patterns have indicated that the glass‐ceramic samples are composed of αZn(BO₂)_2, (Zn)₃(BO₃)_2, CoF₂, CoF₃, Co₃FB₇O₁₃, ZnCo₂O₄, Co₃O₄ crystalline phases. The optical absorption and photoluminescence studies have indicated that there is a gradual increase of tetrahedral cobalt ion concentration with increase of CoO concentration in the glass network. IR spectroscopic studies have pointed out increased degree of polymerization of the zinc oxy fluoro borate glass network with increase of CoO content. The analysis of results of dielectric properties indicated increase of insulating strength of the glass‐ceramics with increase of CoO content. Finally, the dielectric breakdown strength of the samples is measured at room temperature in air medium and it is found to increase from 12.9 to 19.2 kV/cm with increase of CoO from 0.2 to 2.0 mol%. The reasons for such increase of breakdown strength are discussed quantitatively in terms of dielectric parameters with aid of data on spectroscopic properties.     

Effectiveness of sodium silicate as gangue depressants in iron ore slimes flotation

The recovery of iron from the screw classifier overflow slimes by direct flotation was studied.The relative effectiveness of sodium silicates with different silica-to-soda mole ratios as depressants for silica and silicate bearing minerals was investigated.Silica-to-soda mole ratio and silicate dosage were found to have significant effect on the separation efficiency.The results show that an increase of Fe content in the concentrate is observed with concomitant reduction in SiO2 and Al2O3 levels when a particular type of sodium silicate at a proper dosage is used.The concentrate of 58.89wt％ Fe,4.68wt％ SiO2,and 5.28wt％ Al2O3 with the weight recovery of 38.74％ and the metal recovery of 41.13％ can be obtained from the iron ore slimes with 54.44wt％ Fe,6.72wt％ SiO2,and 6.80wt％ Al2O3,when Na2SiO3 with a silica-to-soda mole ratio of 2.19 is used as a depressant at a feed rate of 0.2 kg/t.     

Effect of Prefault Load on Field Overvoltages in Rectifier-Excited Synchrondus Machine During Sequential 3-Phase Fault

ABSTRACT

In a Synchronous machine with rectifier excitation, large reverse voltages may be induced across the field during a transient condition when the field current tends to flow in the reverse direction and is blocked by rectifiers. Earlier investigation on an initially unloaded machine showed that a sequential 3-phase fault, in which a line to line fault develops into a 3-phase fault after a short time, produces field overvoltages whose magnitudes may be comparable to those due to line to line fault. In this paper, analysis has been carried out to estimate the magnitude of the field overvoltage during a sequential 3-phase fault when the machine is assumed to operate on a prefault load. Numerical results show that a sequential 3-phase fault on a machine having prefault loads may be much more severe compared to a line to line fault from the field overvoltage point of view. The results also indicate that very large field overvoltages may be produced during a sequential 3-phase fault on a salient pole machine operating initially on leading power factor loads.