A histological and histomorphometrical evaluation of screw-type calciumphosphate (Ca-P) coated implants; an in vivo experiment in maxillary cancellous bone of goats

The bone response to different calcium phosphate (Ca-P) coated implants was evaluated in a goat animal model. Two types of plasma spray coatings were applied to a commercially pure titanium (cpTi) tapered, conical screw-design implant (BioComp^®); hydroxyapatite (HA-PS) and a dual coating, consisting of FA and HA (FA/HA-PS). In addition an amorphous RF magnetron sputter coating (Ca-P-a) and uncoated implants were investigated. Forty-eight implants were inserted in the maxilla of 12 adult female goats. After implantation periods of 3 and 6 months, the bone implant interface was evaluated histologically and histomorphometrically. After both implantation periods all plasma spray coated implants were maintained. On the other hand three Ca-P-a and two cpTi implants were lost. Histological examination revealed a better bone response to both plasma spray coated implants. Histomorphometrical evaluation confirmed this finding. At 3 and 6 months significantly higher percentages of bone contact (p<0.001, ANOVA) were measured for both plasma spray coated implants than for the cpTi and Ca-P-a implants, while no significant difference (p<0.05) existed between both implantation periods. Degradation of both plasma spray coatings was observed. Supported by the results, it is concluded that, although Ca-P coatings can improve the performance of dental implants, the presence of a Ca-P coating is not the only important factor for bone healing around implants placed in low density trabecular bone.     

MEASUREMENT OF THE SPECIFIC SURFACE AREA OF POWDERS BY THIN LAYER WICKING

The specific surface areas (A) of different clay mineral powders were measured by both the BET method and by thin layer wicking. The values of A for the BET and the wicking experiments coincided within a few percent. Thus, the simple and inexpensive thin layer wicking approach may well suffice to obtain reliable specific surface area values for most powders. From the wicking data it is also possible to obtain a rough estimate of the average particle size.     

Direct finite element design optimisation of the cagelessreluctance synchronous machine

The finite element analysis method is used directly in optimisation algorithms to optimise in multidimensions the design of the cageless reluctance synchronous machine. Two optimisation methods are evaluated to minimise or maximise the function value. These are the direction set method of Powell and the quasi-Newton algorithm. Both methods proved to be successful, with some advantages and disadvantages. Using these methods at a power level below 10 kW, results are given of structures of the reluctance synchronous machine which have been optimised according to specific criteria. Calculated and measured results show that the maximum torque optimum designed reluctance synchronous machine has the advantages of high power density and high efficiency     

Comparison between normal and reverse thin crystalline silicon solar cells

The newly developed ingot growing techniques, as the three-grain and the columnar multigrain ingot processes, are now offering the possibility of slicing thinner wafers (≤ 100 μm). In this paper we present the results obtained on p type large area (≥ 100 cm²) and 100 μm thick wafers by using both conventional and reverse cell manufacturing technologies.The conventional cells are provided with aluminium or boron BSF plus screen-printed silver mirror or a silver-aluminium net; the reverse cells have a FSF and the deep back junction completely covered by a screen-printed or CVD silver layer.The constructing parameters have been chosen on the base of one and two dimensions modeling and both raw material and devices have been completely characterized.This work shows that very thin wafers do not introduce serious problems for the conventional manufacturing of solar cells. The efficiencies of the normal and of the reverse cells are found to be comparable and are of the same order than those of thicker cells, however at a significant lower cost. The main obtained result has to be related to the demonstration of a cell manufacturing feasibility starting from very thin wafers.     

Incomplete inversion and double-valued fundamental linewidth ofinfrared HeNe and HeXe lasers

We have measured the quantum-limited linewidths of small HeNe 3.39 μm and HeXe 3.51 μm lasers. In contrast to the expected Schawlow-Townes behaviour strong deviations from the inverse power dependence are observed, leading to a double-valued relation between the linewidth and the output power. This phenomenon is analyzed in terms of the increase of spontaneous emission, by a factor N_sp, due to incompleteness of the inversion. Our analysis shows that typically N_sp has a value ranging from 1-10. Combining existing models for the pump power dependence of the level populations with measurements of the small signal gain, we are able to explain the observed double-valued linewidth behaviour in a quantitative way     

Mine operating accurate stability control with optical fibersensing and Bragg grating technology: the European BRITE/EURAM STABILOSproject

Recent developments of stability control in mines, essentially based on Ge-doped fiber Bragg gratings (FBG) are reported including results about the different aspects of the system: accurate characterizations of FBG, sensor network topology and multiplexing method, user interface design and sensor packaging     

Theory for passive mode-locking in semiconductor laser structuresincluding the effects of self-phase modulation, dispersion, and pulsecollisions

We present a theory for passive mode-locking in semiconductor laser structures using a semiconductor laser amplifier and absorber. The mode-locking system is described in terms of the different elements in the semiconductor laser structure. We derive mode-locking conditions and show how other mode-locking parameters, like pulse width and pulse energy, are determined by the mode-locking system. System parameters, like bandwidth, dispersion, and self-phase modulation are shown to play an important role in mode-locking conditions and results. We also discuss the effects of pulse collisions and positions of the mode-locking elements inside the cavity on mode-locking stability and show that these effects can be easily included in the presented model. Finally, we give a number of design rules and recommendations for fabricating passively mode-locked lasers     

Phase-insensitive all-optical transistors based on second-ordernonlinearities

We demonstrate and compare two phase-insensitive all-optical transistors (AOT's) based on frequency-degenerate quadratic three-wave interactions. In particular, we demonstrate gain using KTP in a type II geometry. Both AOT's exploit the phase insensitivity inherent to three-wave parametric processes when only two fields are input, providing amplification of a small signal at the operating frequency via the interaction with a second-harmonic wave. The first scheme is based on successive up- and down-conversion (i.e., cascading) while the second relies on parametric down-conversion. We obtain gains of 5 and 160 in the two configurations, respectively, with a significant background and output coherent to the pump in the first case, no background and coherence between output and signal in the second