The hydration of slag,part 1: reaction models for alkali-activated slag

Reaction models are proposed to quantify the hydration products and to determine the composition of C–S–H from alkali-activated slags (AAS). Products of the slag hydration are first summarized from observations in literature. The main hydration products include C–S–H, hydrotalcite, hydrogarnet, AFm phases (C₄AH₁₃ and C₂ASH₈) and ettringite. Then, three stoichiometric reaction models are established correlating the mineral composition of slag (the glass part) with the hydration products. Using the proposed models, quantities of hydration products and composition of C–S–H are determined. The models are validated with a number of experimental investigations reported in literature, yielding good agreement, i.e., these models can successfully predict the hydration reaction of AAS. The models are furthermore applied to calculate the retained water in the hydration products of AAS in different hydration states and a general hydration equation of AAS is derived. As an illustration to one of the model applications, chemical shrinkage of the AAS cement paste in different hydration states are predicted. The chemical shrinkage of AAS is shown to be remarkably higher than OPC. Furthermore, phase distribution in the hardened AAS paste and the porosity are calculated.     

The wear behaviour of oxide ceramics-A Review

The paper reviews the wear behaviour of oxide ceramics. Wear maps are considered and consequently mild and severe wear are defined. Since the use of ceramics in engineering applications require operation in the mild wear regime, the paper concentrates on mild wear mechanisms, but also considers factors which control the transition to severe wear. Within the mild wear regime, the formation of tribofilms are discussed and the manner in which dislocation activity leads to the wear transition is considered. The wear of so-called ceramic nanocomposites, for which no time dependent wear transition has yet been observed, is considered and the reasons for enhanced performance discussed. The role of transformation toughening in zirconia ceramics is considered in detail, and reasons for the generally poor wear response of these materials defined.     

Production of maraging steel grades and the influence of specified and nonspecified elements for special applications

The material properties of maraging steels are greatly affected by the alloy and inclusion content and hence by the production route. This paper describes various past and current production routes at Böhler Edelstahl GmbH and the effect of these routes on the specified element (alloy) and non-specified element (inclusion) contents. Non-metallic inclusions were investigated by EDX analysis. The effects of various alloying and tramp elements on the material properties are presented as a statistical evaluation of previous melts. Nitrogen solubility was calculated with Thermo–Calc for maraging steel Mat.-No. 1.6354 and the precipitation of nitrides is discussed. A proposal is made for the production of melts with improved properties.     

A versatile data acquisition system for time resolved X-ray scattering using gas proportional detectors with delay line readout

A data acquisition system for time resolved X-ray scattering experiments using linear, quadrant or area gas proportional detectors with delay line readout based on commercially available hardware (National Instruments) is described. The system can easily be configured for recording data from point detectors (e.g. photomultipliers and photodiodes) and/or ancillary data only. Applications involving measurements with two different types of time to digital converters illustrate the features and performances of the system.     

Using ion implantation to adjust the transition temperature of superconducting films

We summarize a continuing investigation into using ion implantation to alter the transition temperature of superconducting thin films. The primary motivation for the work presented here was to study the feasibility of using magnetic ion doping to replace the bi-layer T_c control process currently used for certain cryogenic detector applications at National Institute for Standards and Technology. The results from work with various ion species implanted into aluminum, molybdenum, titanium and tungsten host films are presented.     

Development of polyurethane elastomer composite materials by addition of milled fiberglass with coupling agent

Polyurethane elastomer composites were developed using milled fiberglass and their mechanical properties were studied. In particular, the organically chemical treatment of the milled fiberglass was investigated in detail. It was demonstrated that both strength and toughness of the resulting elastomer composites were improved considerably with the addition content of fiberglass. Furthermore, it was indicated that the optimal properties can be achieved by the proper addition of milled fiberglass that was chemically treated using coupling agent.