High bit rate digital subscriber line echo cancellation

The authors explore the issues of complexity, precision, and dynamic range and practical implementation issues such as nonlinearities in high bit rate digital subscriber line (HDSL) echo cancelers. The approach taken is to study these issues analytically using computer simulations, and then to verify simulation results with laboratory prototyping. One of the objectives was to determine whether HDSL echo cancellation will be practical and cost effective within the next several years, consistent with the desire to develop and deploy a repeaterless T1 capability by 1993. Thus, attention is given to practical design issues     

Scheduling constraint generation for communicating processes

This paper describes a new algorithm for generation of scheduling constraints in networks of communicating processes. Our model of communication intertwines the schedules of the machines in the network: timing constraints of a machine may affect the schedules of machines communicating with it. This model of communication facilitates the modular specification of timing constraints. A feasible solution to the set of constraints generated gives a schedule for each machine in the network such that all internal constraints of each machine are satisfied and communication between machines is statically coordinated whenever possible. Static scheduling of communication saves on the cost of handshake associated with dynamic synchronization. Our algorithm can handle complex, state-dependent and cyclic timing constraints. Experimental results show that our algorithm is both effective and efficient     

Effects of category prototypes on performance-rating accuracy.

Two studies examined whether the accessibility of performance prototypes influences performance appraisals. Pilot studies revealed students used performance prototypes when rating instructor performance. Study 1 manipulated the accessibility of these prototypes and the time delay of performance ratings. Results showed no effect of the prime on rating error and accuracy; however, discrimination accuracy decreased over time and recognition bias became more conservative. Study 2 manipulated prototype accessibility and type of rating stimuli (videotape vs. vignette). Rating accuracy and recall were higher for vignette than videotape stimuli, and only those participants exposed to the vignette exhibited priming effects. Results supported transfer-appropriate processing and implied that cognitive primes may have a stronger effect on performance ratings based on "paper-people" than videotaped stimuli. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Interaction Between a Drying Agent and Particles Dispersed by an Airstream Atomizer Inside a Drying Chamber

Results of an experimental study of the aerodynamics and spray density distribution of a liquid dispersed by an airstream atomizer inside a drying chamber. Velocity components of the drying agent and their radial distributions as a function of the distance from the spray plane are determined. Relationships for the distribution of dispersed liquid inside the drying chamber are derived. Interactions between the drying agent and the product in the drying chamber are analyzed.     

Dielectric barrier discharge treatments at atmospheric pressure for wood surface modification

In this research, the effect of dielectric barrier discharge on mechanically manufactured (sawn, planed or polished) wood surfaces is investigated. The experiments have shown that the best hydrophilia is obtained with a cold plasma discharge in air under atmospheric pressure. Other gases such as helium, nitrogen, and argon have been tested, too. Changes of the wood surface properties were determined by absorption of water and contact angle measurements. As a result of a 1 to 20 seconds long exposure to plasma, wood surfaces became hydrophilic. The absorption of water in wood can be changed up to 22 times higher after plasma treatment in air for 20 seconds duration. The fracture strength of glued wood has been increased by 68% after this plasma pretreatment. Using plasma treatment in methane or acetylene wood surfaces are changed to hydrophobic properties. After plasma treatment for 1 min. in a Ar:CH₄=80:20 gas mixture under atmospheric pressure, the absorption of water in wood is 32 times lower than without plasma treatment. As mentioned before, plasma treatment can produce hydrophobic and hydrophilic wood surfaces. But a good homogeneity of the gas discharge is necessary for the plasma treatment of wood. Zusammenfassung Im Rahmen dieser Arbeit werden die Auswirkungen der dielektrisch behinderten Entladung bei Atmosphärendruck auf mechanisch bearbeitete Holzoberflächen (gesägt, gehobelt oder geschliffen) untersucht. Die Experimente haben gezeigt, dass die höchste Hydrophilität bei einem in Luftatmosphäre gezündetem Plasma erreicht wird. Es werden auch andere Gase verwendet, wie z.B. Helium, Stickstoff und Argon. Zur Untersuchung der veränderten mechanischen und energetischen Eigenschaften der Holzoberflächen werden der Tropfen-Versuch und die Kontaktwinkelmessung verwendet. Durch eine 1 bis 20 Sekunden lange Plasmabehandlung können die Oberflächen hydrophil gestaltet werden. So kann die Eindringzeit von Wasser um Faktor 22 gesteigert werden durch eine 20 Sekunden lange Plasmabehandlung in Umgebungsluft. Die Bruchfestigkeit von Leimholz wird durch die gleiche Plasmavorbehandlung um 68% gesteigert. Werden als Plasmabehandlungsgas Methan oder Acetylen eingesetzt, so wird die Holzoberfläche hydrophob. Durch eine 60 Sekunden lange Plasmabehandlung in einem Ar:CH₄=80:20 Gasgemisch bei Atmosphärendruck wird die Eindringszeit von Wasser um den Faktor 32 gesenkt. Mit Hilfe der Plasmabehandlung können also sowohl hydrophobe als auch hydrophile Holzoberflächen erzeugt werden. Jedoch wird für die Plasmabehandlung von Holz eine sehr homogene Gasentladung benötigt.     

Micro-electro-discharge machining as microsensor fabrication technology

This paper presents the design and fabrication of three miniaturized mechanical sensors to demonstrate the three-dimensional machining capabilities of micro-electro-discharge machining (EDM). The first sensor is an inertial bi-axial inclination sensor. The displacement of an inertial mass is measured optically by means of a two-dimensional position sensitive device (PSD). The machining freedom of micro-EDM makes it possible to produce both sensor and housing in one monolithic structure. The second sensor is an inertial uni-axial inclination sensor, which demonstrates the compatibility of the micro-EDM technology with the conventional photolithographic micromachining technologies. The mechanical structure of the sensor is machined by micro-EDM and the capacitive sensing part is produced by lithography. The aim of the integration is to set up a hybrid technology, which inherits the benefits of both micro-EDM and photolithography. The third miniaturized sensor is a three-component force sensor. The mechanical structure of the force sensor converts forces into displacements, which are measured optically. The mechanical structure of the force sensor is produced by wire-EDM and micro-EDM.     

Numerical simulation of ion-exchange in glass for integratedoptical components

A numerical model based on the finite-element method for solving the nonlinear diffusion equation of ion-exchange in glasses is presented. The model is applied to the calculation of the concentration profile for a Ag⁺-Na⁺ ion-exchanged channel waveguide. The calculated concentration profile is in good agreement with a measured refractive-index profile of a waveguide fabricated with the same parameters as used in the calculations