Analysis of time-frequency duality of MC and DS CDMA for multiantenna systems on highly time-varying and wide-band channels

Direct sequence (DS) and multicarrier (MC) are code-division multiple-access (CDMA) schemes based on single-carrier and MC modulations, respectively. While in DS CDMA, spreading is performed by increasing the transmission rate, or in the time domain, in MC CDMA, spreading is performed using several subcarriers, or in the frequency domain. In this paper, it is shown that MC and DS CDMA are time-frequency dual systems. Their analysis in time- and frequency-dispersive multiple-input multiple-output channels revealed that they can be described equally in terms of dual-channel functions, therefore exhibiting the same performance on dual channels. Furthermore, the duality property is used to derive matched filters for highly time-variant and wide-band channels. Finally, other issues involved in the comparison of DS and MC, namely spreading-sequence design and multiuser detection, are addressed.     

Yielding- and fracture behaviour of ferritic steels in the transition region of quasistatic to dynamic loading

This paper presents results of investigations on the influence of loading rate on yielding and fracture behaviour of ferritic steels. The range of loading rates was below a certain level at which a special stress wave analysis is required. Concerning the yielding behaviour it was found, that the yield strength can be predicted by the model of thermally activated flow. The strain hardening dσ/dε appeared to be independent of strain rate, if adiabetic heating can be neglected. Concerning the fracture behaviour it is demonstrated that the K_lc-T-curves are shifted to higher temperatures with increasing loading rate. The temperature shift could be correlated with the strain rate sensitivity m = d lnσ/d lnε. The ductile/brittle transition temperature increases with incrasing loading rate. For the upper shelf region crack resistance curves as a function of loading rate are presented. It is shown that the crack length can be determined using the key-curve-method. A slightly increasing tendency of the evaluated J_R-curves was found.     

Nitrogen management in reservoir catchments through constructed wetland systems.

In this study, nitrogen removal was investigated in pilot-scale subsurface flow (SSF) and in free water surface flow (FWS) constructed wetlands installed in the campus of TUBITAK-Marmara Research Center, Gebze, near Istanbul, Turkey. The main purposes of this study are to apply constructed wetlands for the protection of water reservoirs and to reuse wastewater. Experiments were carried out at continuous flow reactors. The effects of the type of plants on the removal were investigated by using emergent (Canna, Cyperus, Typhia spp., Phragmites spp., Juncus, Poaceae, Paspalum and Iris.), submerged (Elodea, Egeria) and floating (Pistia, Salvina and Lemna) marsh plants at different conditions. During the study period HLRs were 30, 50, 70, 80 and 120 L m(2)d(-1) respectively. The average annual NH4-N, NO(3)-N, organic N and TN treatment efficiencies in SSF and FWS wetlands are 81% and 68%, 37% and 49%, 75% and 68%, 47% and 53%, respectively. Nitrification, denitrification and ammonification rate constant (k20) values in SSF and FNS systems have been found as 0.898 d(-1) and 0.541 d(-1), 0.488 d(-1) and 0.502 d(-1), 0.986 d(-1) and 0.908 respectively. Two types of the models (first-order plug flow and multiple regression) were tried to estimate the system performances.     

Surface topography of planar PMMA grating structures produced by the UV-laser based phase mask method

Surface relief gratings are written into the surface of a planar PMMA substrate by the UV-excimer laser based phase mask method. The surface relief grating topography (grating amplitude and grating constant) is investigated in dependence on the laser irradiation parameters (fluence and irradiation dose) yielding some information relevant for the ablation and grating formation mechanism.     

Theoretical and experimental study of mass sensitivity of PSAW-APMson ZX-LiNbO3

Acoustic plate mode (APM) devices have recently been used as sensing elements, both for the physical measurement of fluid properties and in biosensor applications. One of the primary interaction mechanisms in these devices is mass loading caused by the added mass bound to the layered crystal surface. However, the material properties of these thin composite layers are not well characterized or known as is required in order to accurately predict the sensor response. In the present work, perturbation theory is used to derive expressions for the sensitivity of the APM sensors to mass loading and viscoelastic stiffening. Mass sensitivity experiment was conducted on ZX-LiNbO₃ in a liquid environment to accurately reflect the sensitivity of an actual biosensor and the results are compared to theory. The measured data show a f² dependence for the mass sensitivity for APMs on ZX-LiNbO₃ in the measured frequency range, which indicates a SAW-like behavior. This behavior is due to the fact that the acoustic plate modes on ZX-LiNBO₃ are pseudo-SAW (PSAW) derived, and the acoustic energy is confined to the sensing surface. As a result, the APMs on ZX-LiNbO₃ are referred to as PSAW-APMs. Discussions are given in terms of the added mass which occurs in typical biosensor applications     

Identification of Factors Affecting Preservative Efficacy and Chemical Stability of Lamivudine Oral Solution Through Statistical Experimental Design

To identify factors affecting the chemical stability and preservative efficacy of lamivudine oral liquid formulations, an optimization study using a central composite design was performed. In this design, five factors, each at three levels, were investigated: pH (4.5, 5.5, and 73, sucrose (5%, 20%. and 50% w/v), propylene glycol (0% 2%, and 5% w/v), glycerin (4% 8%, and 12% w/v). and EDTA (0.100. 0.175, and 0.250 mg/mL). All formulations contained a constant concentration of lamivudine, parabens, and artificial strawberry and banana flavors. All formulations were evaluated for preservative effectiveness against USP and BP standards and for chemical stability at 30°C and 40°C for three months. All formulations were effective against bacteria and yeasts, but indicated reduced preservative effectiveness against the mold Aspergillus niger. Preservative effectiveness improved with increasing pH (4.5 to 7.5) and to a lesser extent with increasing EDTA concentration (0.100 to 0.250 mg/mL). Increasing glycerin concentration (4% to 12% w/v) slightly decreased preservative effectiveness. Over the concentration ranges tested, no change in preservative effectiveness was noted with concentration changes in sucrose or propylene glycol. The pH was the main factor influencing the chemical stability of the drug and preservatives in this study. Lamivudine chemical stability increased with increasing pH from 4.5 to 7.5. Methyl and propylparaben showed extensive degradation at pH 7.5.