Lens antennas for mobile broadband systems in the millimetre-waverange

An improved antenna for a wireless mobile broadband system (e.g. as realised by Bosch as a demonstrator) is proposed. By means of a shaped dielectric lens the radiation pattern of a primary antenna (e.g. a short helical structure) can be shaped to optimise the power distribution across an indoor cell. The calculated performance of lenses designed for the 30 and 60 GHz bands by using geometric optics shows good agreement with measured results     

Surface leakage currents in SiN/sub x/ passivated AlGaN/GaN HFETs

A novel guarded surface leakage test structure is used to isolate the surface and bulk leakage contributions to gate current in AlGaN/GaN HFETs. Passivation with various recipes of SiN/sub x/ always resulted in the commonly observed increase in gate leakage, which was found to be dominated by bulk leakage through the AlGaN. However, high temperature deposited SiN/sub x/ recipes gave a 1-2 orders reduction in surface leakage, whereas low temperature deposition gave an increase. Gate lag measurements were found to correlate closely with the surface leakage component, giving direct evidence that the key device problem of current slump is associated with current flow at the AlGaN surface.     

Adaptive two-loop Voltage-mode control of DC-DC switching converters

A new two-loop control scheme for voltage-mode control (VMC) of dc-dc switching converters is presented. The proposed method adds a high-gain robust loop with two controllers to the conventional VMC loop, achieving an analog "adaptive" loop in which the "equivalent voltage regulator" varies with the changing power stage parameters given as follows: 1) input voltage; 2) load; and 3) component tolerances. The loop significantly improves the disturbance rejection of the control system, i.e., closed-loop output impedance and audiosusceptibility while preserving the stability and the loop gain crossover frequency to a significant extent. Both the small-signal analysis and the experimental results carried out on a buck converter demonstrate the superiority of the proposed scheme with respect to the conventional single loop.     

Characterization and comparison of PECVD silicon nitride and silicon oxynitride dielectric for MIM capacitors

In this letter, we report on the electrical characteristic and the comparison of the metal-insulator-metal (MIM) capacitors with PECVD silicon nitride (SiN) and silicon oxynitride (SiON). Both capacitors are found to exhibit low leakage and high breakdown field strength, as well as absence of dispersive behavior, good linearity, and comparable quality factor behaviors.     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

Low RF noise and power loss for ion-implanted Si having an improved implantation process

Very-low-transmission line noise of <0.25 dB at 18 GHz and low power loss /spl les/0.6 dB at 110 GHz have been measured on transmission lines fabricated on proton-implanted Si. In contrast, a standard Si substrate gave much higher noise of 2.5 dB and worse power loss of 5 dB. The good RF integrity of proton-implanted Si results from the high isolation impedance to ground, as analyzed by an equivalent circuit model. The proton implantation is also done after forming the transmission lines at a reduced implantation energy of /spl sim/4 MeV. This enables easier process integration into current VLSI technology.     

High-performance surface-micromachined inchworm actuator

This work demonstrates a polycrystalline silicon surface-micromachined inchworm actuator that exhibits high-performance characteristics such as large force (/spl plusmn/0.5 millinewtons), large velocity range (0 to /spl plusmn/4.4 mm/sec), large displacement range (/spl plusmn/100 microns), small step size (/spl plusmn/10, /spl plusmn/40 or /spl plusmn/100 nanometers), low power consumption (nanojoules per cycle), continuous bidirectional operation and relatively small area (600 /spl times/ 200/spl mu/m/sup 2/). An in situ load spring calibrated on a logarithmic scale from micronewtons to millinewtons, optical microscopy and Michelson interferometry are used to characterize its performance. The actuator consists of a force-amplifying plate that spans two voltage-controlled clamps, and walking is achieved by appropriately sequencing signals to these three components. In the clamps, normal force is borne by equipotential rubbing counterfaces, enabling friction to be measured against load. Using different monolayer coatings, we show that the static coefficient of friction can be changed from 0.14 to 1.04, and that it is load-independent over a broad range. We further find that the static coefficient of friction does not accurately predict the force generated by the actuator and attribute this to nanometer-scale presliding tangential deflections.     

Manipulation of microenvironment with a built-in electrochemical actuator in proximity of a dissolved oxygen microsensor

Biochemical sensors for continuous monitoring require dependable periodic self diagnosis with acceptable simplicity to check its functionality during operation. An in-situ self-diagnostic technique for a dissolved oxygen microsensor is proposed in an effort to devise an intelligent microsensor system with an integrated electrochemical actuation electrode. With a built-in platinum microelectrode that surrounds the microsensor, two kinds of microenvironments, called the oxygen-saturated or oxygen-depleted phases, can be created by water electrolysis, depending on the polarity. The functionality of the microsensor can be checked during these microenvironment phases. The polarographic oxygen microsensor is fabricated on a flexible polyimide substrate (Kapton) and the feasibility of the proposed concept is demonstrated in a physiological solution. The sensor responds properly during the oxygen-generating and oxygen-depleting phases. The use of these microenvironments for in-situ self-calibration is discussed to achieve functional integration, as well as structural integration, of the microsensor system.     

Wavelength stabilizer for telecommunication lasers: design and optimization

We introduce a novel method for the wavelength stabilization of semiconductor lasers for telecommunications. The approach is based on a wavelength-sensitive photodetector which, in a feedback system, generates an error signal apt to tune the source to the desired value. We extensively investigate the influence of various design parameters on performance figures such as tunability, steady-state error, and temperature dependence, as well as fabrication tolerances. The results are compared with standard specifications for wavelength-division-multiplexed optical communications with various channel spacings.     

Performance failure analysis of EDFA cascades in optical DWDM packet-switched networks

A simple and comprehensive technique to determine the probability that a cascade of erbium-doped fiber amplifiers (EDFAs) may be driven into unacceptable regimes of bit error rate (BER) and/or gain levels is presented. This technique allows network designers to determine the tolerances by which the signal power levels may deviate from their predesigned average values and still give acceptable gain variances and BERs at the receiver. We show that even in the signal power range well above the receiver sensitivities (-38 dBm/ch) where the gain spread is not significant, the corresponding spread in BER due to random arrival of packets might result in unacceptable performance. We show for typical levels of operation, the BER temporarily (for about 3 /spl mu/s) deviates to below 10/sup -9/ (10/sup -15/) with a probability of 10/sup -3/ (10/sup -2/), for 100 (64) channels. We show that the gain spread for a single EDFA can be negligible for a range of signal and pump powers at a given average gain.