The dominance of the K I-field for a crack under stress wave loading

The extent of the dominant singular field is investigated for a finite crack under stress wave loading. Using a boundary integral equation method the complete solution as well as the near field solution is determined. A comparison of the two fields indicates that the singular field dominates within a small domain at the crack tip. The size of the dominance region in the dynamic case may be very different from that in the static case.     

Probabilistic evaluation of lateral extent of soil liquefaction under earthquake loading

A Monte Carlo simulation method for calculating the probability of soil liquefaction of a finite area in which the ground motion is propagated upward from the bedrock through the soil layers is presented. The vertical propagation of the ground motion through the soil layers is analyzed using random vibration analysis. To account for the variability of soil properties with depth, the soil deposit is divided into layers. Within each layer the horizontal statistical correlation of the undrained cyclic shearing strength against liquefaction is taken into consideration by describing it as a two-dimensional homogeneous random field. The method computes the probability of liquefaction spreading over a specified area under a given earthquake loading considering the effects of spatial correlation of soil properties.     

Measurements to distinguish fuel elements with and without thorium content by gammaspectrometry in hot cells

The T1208 inventory in a HTR fuel element is transmuted from Th232. By measuring the T1208 gamma radiation in a suitable scan configuration it is possible to distinguish fuel elements with and without Thorium contents non-destructively even after a long cooling time.     

Crack growth measurements on components under cyclic loading: comparison of different methods

The cyclic crack growth behaviour was measured by means of d.c. potential drop, a.c. potential drop, ultrasonic and crack-opening displacement (COD) methods. The methods were applied to component tests on straight pipes with an outer diameter of approximately 800 mm and a wall thickness of approximately 50 mm. The pipes were subjected to constant internal pressure (about 15 MPa) and either an alternating (or pulsating) or a quasi-static bending moment using d.c. potential drop, a.c. potential drop, ultrasonic and flaw-opening (COD) methods. The efficiency of the particular methods has been proved by comparison with fractographical analysis of the fracture surfaces.     

Synthesis and characterization of tungsten disulphide films grown by pulsed-laser deposition

The synthesis and characterization of tungsten disulphide (WS₂) films grown on 440C stainless steel substrates using the 248 nm line from a KrF excimer laser are reported. Film properties could be adjusted by controlling substrate temperature and by laser or thermal anneals. X-ray photoelectron spectroscopy, glancing angle XRD, Raman spectroscopy and high-resolution scanning electron microscopy were used to evaluate film chemistry, crystallinity and morphology. Films grown at room temperature were amorphous, near stoichiometric, and had a multiplicity of chemical states. Local order and bonding were improved most dramatically through post-deposition laser anneals. Crystallite size could be increased by raising the substrate temperature during deposition and, to a lesser degree, by post-deposition thermal anneals. Local disorder was observed within the larger crystallites compared to those that were laser annealed. Crystallinity was induced in amorphous films by mechanical rubbing at room temperature under conditions where frictional heating was negligible. The degree of control over film properties provided by PLD demonstrates its value for growing/designing tribological coatings.     

EFFECT OF THE RATIO Th/U ON TL DATING ACCURACY

ＥＦＦＥＣＴＯＦＴＨＥＲＡＴＩＯＴｈ／ＵＯＮＴＬＤＡＴＩＮＧＡＣＣＵＲＡＣＹ￥Ｐ．Ｌ．Ｌｅｕｎｇ（梁宝鎏）；ＭｉｃｈａｅｌＪ．Ｓｔｏｋｅｓ（ＤｅｐａｒｔｍｅｎｔｏｆＰｈｙｓｉｃｓａｎｄＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅ，ＣｉｔｙＰｏｌｙｔｅｃｈｎｉｃｏ...     

高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。