降低烧结返矿率的途径与实践

通过对影响烧结返矿率的因素进行分析，从优化配料、强化制粒和造球、提高料层厚度、实现低碳低水均质烧结等几个方面着手，使烧结返矿率从1998年的23．6％降到了2003年的16．9％。     

Effect of Y2O3, CeO2 on Sintering Properties of Si3N4 Ceramics

The effect of rare earth oxides Y203 or Ce02 on sintering properties of Si3N4 ceramics was studied and the mechanism of assisting action during sintering was analyzed. The results in dicate that the best sintering properties appear in Si3N4 ceramics with 5% Y203 or 8% CeO2. Secondary crystallites are formed at grain boundaries after heat treatment,which decreases the amount of glass phase and contributes to the improvement of high-temperature mechanical properties of silicon nitride.     

文件静态特性评估下的木马检测机制

本文提出了一种针对木马的静态信息进行分析的新的检测机制,建立了基于BP神经网络的数据处理模型。PE文件是Windows平台下的可执行文件,也是木马等后门程序的主要载体, 由于PE文件的结构复杂、灵活,而BP神经网络摸型的自身要求,导致数据的建摸过程遇到两个难点,本文首先引入了变化粒度的概念,解决了输入端非线性数据的问题。同时,也解决了将PE文件中大量的字符串归一化(0,1)区间)的问题,最终建立了一套较为理想的解决方案,取得了较为理想的测试数据。     

微波仪器远程自动测试系统的设计与实现

针对大多通信测试仪器仅局限于本地测试监控的现状,提出了一种将本地测试仪器用于对远程微波设备进行测试监控的开发模式,从而实现了远程仪器的自动化测试。分别就系统中的关键技术和交互方式作了详细的介绍,得出系统具有较强的可扩展性,且简单易操作的特点,相信该系统会有广阔的的应用前景。     

Fast adders using enhanced multiple-output domino logic

Using an enhanced multiple output domino logic (EMODL) implementation of a carry lookahead adder (CLA), sums of several consecutive bits can be built in one nFET tree with a single carry-in. Based on this result, a new sparse carry chain architecture is proposed for the CLA adder. We demonstrate the design approach using a 32-b adder, and show that only four carries are sufficient for generating all sums, with a consequent reduction in the number of stage delays. Using a 1.2-μm CMOS technology, we verify our simulation procedures by fabrication and measurement of a 2.7 ns critical path     

铝钛双金属板KR曲线测定

利用宽３００ｍｍ、长／宽＝１的横向ＣＴＴ试样对国产铝钛双金属板做了常规力学性能测定，并按航标测定了ＫＲ曲线，经过柔度法和Ｋ值计算，分别测得了ＫＲｉ和ａｉ数据，确定了临界的ＫＣ值通过性能数据对比，研制的材料达到了进口料的性能要求。     

本钢炼焦煤最佳配比分析

结合本钢的生产实际，对炼焦煤的最佳配比作了比较具体的分析，同时对资源，质量、成本也作了比较详细的调查，并提出了本钢焦化厂最佳配煤比方案，由此可看出，最大限度地降低采购成本，继续开发合理的配煤比例，具有广阔的前景。     

A probabilistic method for the design of power grounding systems

An improved multivariable, probabilistic method for the safety analysis of power grounding systems is presented. The application of this method is demonstrated in four examples. The first three examples illustrate the practical evaluation of one new and two existing substation grounding grids when the substation is connected to an overhead distribution system. The fourth example ascertains the relative impact of a difference between the S curve of IEC Publication 479 and Dalziel's equation for the allowable body current used in ANSI/IEEE Std 80-1986 on the validity of an exposure model based on the requirements of Std 80. In this example, the statistical data on ground faults have been taken from actual system records. Further possible refinements of the exposure model are discussed     

智能工作站主机的MMPIS实验模型研究──一个全互连式结构MMPIS硬件环境的设计与实现

本文介绍中日国际合作开发研究的Ａ１型智能网（Ａ１型ＩＮ）智能工作站（ＩＷ）主机的并行推理硬件结构的实验模型设计与实现，给出了一种并行推理硬件支持环境实现方案和该方案在实现中若干问题的解决方法。     

Study and design of step-index channel waveguide bends withlarge-angle and low-loss characteristics

By using micro-prisms, improved three-dimensional (3-D) bends of the embedded and buried waveguides of step-index profile are proposed. A simple phase compensation rule for the optimal design of the micro-prism is also presented. Through the simulation of 3-D semivectorial finite-difference beam propagation method, the transmission characteristics of the improved bends are shown to have been enhanced dramatically as compared with those of the conventional ones. Even for a bend angle of as large as 10°, the normalized transmitted power can still be greater than 95%. These results of 3-D bends are then compared with those of the two-dimensional (2-D) ones which are simplified from 3-D structures by the effective index method, and physical explanation of the discrepancy between the 3-D and 2-D results is introduced. The influences of waveguide structures and prism parameters on the transmission characteristics are discussed in detail. Some criteria for the design of large-angle low-loss 3-D improved bends are also accessed