High-Tc dc-SQUID magnetometer and its application in eddy current non-destructive evaluation

We have fabricated and tested a high-T_c dc-SQUID magnetometer patterned on a YBCO thin film deposited on a SrTiO₃ bicrystal substrate. The measurement of noise spectrum at 77 K showed that the magnetometer has a white noise of 333 fT/Hz^1/2 without superconducting shield, corresponding to a flux sensitivity of 14.5 μΦ₀/Hz^1/2. We constructed a test system for eddy current non-destructive evaluation of conducting aluminum plates by using the magnetometer. Flaws over 10 mm below the surface can be clearly identified. By mapping the magnetic field distribution, we can locate the flaw position. The signals caused by flaw were expanded due to the use of double-D type driving coil with a wider central slit. The experimental results confirmed that this test system could operate in a magnetic unshielded environment.     

Design optimization of radially magnetized, iron-cored, tubular permanent-magnet machines and drive systems

In this paper we deduce, from analytical field solutions, the influence of leading design parameters on the performance of a radially magnetized, iron-cored, tubular permanent-magnet machine and its drive system. We derive analytical formulas for predicting the open-circuit electromotive force, the thrust force, the iron loss, and the winding resistance and inductances, as well as the converter losses. The force density, the machine and drive system efficiencies, and the power factor and converter volt-ampere (VA) rating are established as functions of a set of machine dimensional ratios, with due account of magnetic saturation and subject to a specified thermal constraint. We validate the utility and accuracy of the analytically derived formulas by finite-element calculations. Finally, we show that the design optimization of such a linear drive system must account for the losses and VA rating of the converter as well as the design parameters of the tubular machine.     

Analysis and comparison of two-dimensional permanent-magnet arrays for planar motor

This paper investigates three kinds of permanent-magnet arrays used in planar motors with polarity centers distributed in the lattices of a matrix. The magnetic field of every kind of magnet array is analyzed by analytical methods. First, we give a Laplace equation of magnetic scalar potential and a series of boundary conditions. Then, we derive the analytical expressions of magnet field strength and magnet flux density in the air gap of each kind of magnet array by the method of separation of variables. Finally, we compare the three types of magnet arrays on the basis of the analytical solutions.     

单膛石灰竖窑的改造

我厂竖窑容积为250m^3，设计利用系数为0．85t/(m^3．d)。随烧结产量的不断增加，石灰产量已不能满足烧结生产的需要。为了提高石灰产量，进行了扩容改造，容积由原来250m^3增加到298m^3，并针对目前生产实际提出下一步改造设想。     

Grain refinement of Al-7Si alloys and the efficiency assessment by recognition of cooling curves

Under sand cup solidification condition, the influence of Ti, B concentration, and holding time on the grain size of a high-purity Al-7Si alloy has been systematically studied. It is found that the grain size decreases rapidly at lower Ti or B additions, and is almost constant at the higher concentrations. For Al-3B refined Al-7Si alloys, the grain size increases at the initial period of holding time, and then rapidly becomes independent of holding time; while for Al-7Si alloys refined with Al-5Ti-1B, the grain size increases with holding time throughout. To evaluate the refinement efficiency, a new method named “intelligent evaluating of melt quality by pattern recognition of thermal analysis cooling curves” has also been introduced in this article. The results show that comparing the cooling curve of the evaluated melt with those in a database to find the most similar one to it can precisely assess the grain refinement efficiency of the measured Al-7Si alloy. In addition, the influence of Ti, B addition levels, and pouring temperatures on some characteristic parameters of cooling curve has also been discussed.     

含V、N无缝钢管表面外折缺陷产生原因的分析

通过对鞍钢生产的部分批号V、N微合金强化无缝钢管及生产该钢管的原料连铸坯和连轧管坯的表面缺陷进行研究，分析了含V、N钢管表面外折缺陷的成因，提出了改善钢管表面质量的方法。采用改进后工艺生产的无缝管，其表面外折废品量大幅度降低。     

降低烧结返矿率的途径与实践

通过对影响烧结返矿率的因素进行分析，从优化配料、强化制粒和造球、提高料层厚度、实现低碳低水均质烧结等几个方面着手，使烧结返矿率从1998年的23．6％降到了2003年的16．9％。     

Effect of Y2O3, CeO2 on Sintering Properties of Si3N4 Ceramics

The effect of rare earth oxides Y203 or Ce02 on sintering properties of Si3N4 ceramics was studied and the mechanism of assisting action during sintering was analyzed. The results in dicate that the best sintering properties appear in Si3N4 ceramics with 5% Y203 or 8% CeO2. Secondary crystallites are formed at grain boundaries after heat treatment,which decreases the amount of glass phase and contributes to the improvement of high-temperature mechanical properties of silicon nitride.