Water quality of Scottish rivers: spatial and temporal trends

The Harmonised Monitoring Scheme (HMS) was initiated in 1974 and represents the best-organised source of temporal and spatial data describing water quality for the major mainland rivers of Scotland, England and Wales. This paper presents the first detailed analysis of HMS data for Scotland, and identifies temporal changes in water quality from 1974 to 1995. From a concomitant analysis of catchment land cover characteristics, water quality indices have been linked with potential 'drivers' of change, influencing both point and diffuse sources. Nitrate concentrations between rivers are highly correlated with the amount of arable land, and relationships exist between grassland cover, orthphosphate-P and suspended solids concentrations. Similarly, urban catchments are highly correlated with ammonium-N, orthophosphate-P and suspended solids. Spatial and temporal trends in water quality for the rivers of Scotland are discussed.     

3D Active Edge Silicon Detector Tests With 120 GeV Muons

3D detectors with electrodes penetrating through the silicon wafer and covering the edges were tested in the SPS beam line X5 at CERN in autumn 2003. Detector parameters including efficiency, signal-to-noise ratio, and edge sensitivity were measured using a silicon telescope as a reference system. The measured sensitive width and the known silicon width were equal within less than 10 mum.     

Freeze-form extrusion fabrication of functionally graded materials

Presented in this paper is a novel additive manufacturing technology for making three-dimensional parts with functionally graded materials (FGMs), called Freeze-form Extrusion Fabrication (FEF). The system development included a triple-extruder mechanism, extruder modeling and control, pastes extrusion planning for desired composition gradients, and software coding for motion and extrusion control. The effectiveness of the developed FEF system was demonstrated first by fabricating limestone (CaCO₃) parts with graded colors and then by fabricating ‘green’ parts with graded compositions between alumina (Al₂O₃) and zirconia (ZrO₂). The fabricated part went through post-processing, and the sintered part was analyzed using energy dispersive spectroscopy (EDS) to determine its material compositions.     

The adsorption of an epoxy acrylate resin on aluminium alloy conversion coatings

A thermodynamic study of the adsorption of an epoxy acrylate resin used for UV-cured coatings on two different anticorrosion pretreatments on aluminium alloys relevant to aerospace industry has been undertaken. Aluminium alloy Al2219 specimens, treated with an inorganic chromate based conversion coating (Alodine 1200S) and an organic titanium based conversion coating (Nabutan STI/310), were immersed in solutions of different concentrations of the resin and adsorption isotherms were determined by assessing the uptake of the adsorbate, as a function of solution concentration, by time-of-flight secondary ion mass spectrometry (ToF-SIMS). The results show different behaviour for the two substrates, which can be attributed to the organic component of the titanium based coating. In the case of the inorganic conversion coating a clear plateau is achieved at relatively low concentrations and at a lower level of adsorption than for the hybrid coating. The data for both the coatings conform well to the Langmuir model, the organic coating, as well as showing a higher level of adsorption of the resin, also presents oscillatory behaviour at low concentration, which is shown to be complementary to the behaviour of the reactive diluent included with the epoxy acrylate to aid processing. A discussion of this competitive adsorption of the epoxy resin and the diluent on the different substrates is presented, based on considerations of the chemistry of the systems under investigation.     

Mineralization of a sorbed polycyclic aromatic hydrocarbon in two soils using catalyzed hydrogen peroxide

Hydrogen peroxide (H2O2) catalyzed by soluble iron or naturally occurring soil minerals, (i.e., modified Fenton's reagent) was investigated as a basis for mineralizing sorbed and NAPL-phase benzo[a]pyrene (BaP), a hydrophobic and toxic polycyclic aromatic hydrocarbon, in two soils of different complexity. 14C-Benzo[a]pyrene was added to silica sand and a silt loam soil, and mineralization was investigated using three-level central composite rotatable experimental designs. The effects of H2O2 concentration, slurry volume, and iron(II) amendment were investigated in the silica sand systems. In a Palouse loess silt loam soil, the variables included H2O2 concentration, slurry volume, and pH, with H2O2 catalyzed by naturally occurring iron oxyhydroxides. Regression equations generated from the data were used to develop three-dimensional response surfaces describing BaP mineralization. Based on the recovery of 14C-CO2, 70% BaP mineralization was achieved in the sand within 24 h using 15 M H2O2 and an iron(II) concentration of 6.6 mM with a slurry volume of 0.3 x the field capacity of the sand. For the silt loam soil, 85% mineralization of BaP was observed using 15 M H2O2, no iron amendment, and a slurry volume of 20 x the soil field capacity. The balance of the radiolabeled carbon remained as unreacted BaP in the soil fraction. Gas-purge measurements over 5 d confirmed negligible desorption under nontreatment conditions. However, oxidation reactions were complete within 24 h and promoted up to 85% BaP mineralization, documenting that the natural rate of desorption/dissolution did not control the rate of oxidation and mineralization of the BaP. The results show that catalyzed H2O2 has the ability to rapidly mineralize sorbed/NAPL-phase BaP and that partitioning, which is often the rate-limiting factor in soil remediation, does not appear to limit the rate of vigorous Fenton-like treatment.     

A scalable manufacturing process for flexible active‐matrix e‐paper displays

Abstract— A scalable manufacturing process for fabricating active‐matrix backplanes on low‐cost flexible substrates, a key enabler for electronic‐paper displays, is presented. This process is based on solution processing, ink‐jet printing, and laser patterning. A multilayer architecture is employed to enable high aperture ratio and array performance. These backplanes were combined with E Ink electrophoretic media to create high‐performance displays that have high contrast, are bistable, and can be flexed repeatedly to a radius of curvature of 5 mm.     

Active-edge planar radiation sensors

Many systems in medicine, biology, high-energy physics, and astrophysics require large area radiation sensors. In most of these applications, minimizing the amount of dead area or dead material is crucial. We have developed a new type of silicon radiation sensor in which the device is active to within a few microns of the mechanical edge. Their perimeter is made by a plasma etcher rather than a diamond saw. Their edges can be defined and also passivated by growing, in an intermediate step, a field oxide on the side surfaces. In this paper, the basic architecture and results from a synchrotron beam test are presented.