宝钢2号高炉4号热风炉凉炉实践

对宝钢2号高炉4号热风炉凉炉的原因、凉炉的前期族备工作、凉炉的设备和方法以及凉炉的实际效果进行了总结。通过这次凉炉实践，取得了一些有价值的经验，这些经验对今后宝钢砖硅热风炉的凉炉具有重要的参考意义。     

Trellis and convolutional precoding for transmitter-based interference presubtraction

This paper studies the combination of practical trellis and convolution codes with Tomlinson-Harashima precoding (THP) for the presubtraction of multiuser interference that is known at the transmitter but not known at the receiver. It is well known that a straightforward application of THP suffers power, modulo, and shaping losses. This paper proposes generalizations of THP that recover some of these losses. At a high signal-to-noise ratio (SNR), the precoding loss is dominated by the shaping loss, which is about 1.53 dB. To recover shaping loss, a trellis-shaping technique is developed that takes into account the knowledge of a noncausal interfering sequence, rather than just the instantaneous interference. At rates of 2 and 3 bits per transmission, trellis shaping is shown to be able to recover almost all of the 1.53-dB shaping loss. At a low SNR, the precoding loss is dominated by power and modulo losses, which can be as large as 3-4 dB. To recover these losses, a technique that incorporates partial interference presubtraction (PIP) within convolutional decoding is developed. At rates of 0.5 and 0.25 bits per transmission, PIP is able to recover 1-1.5 dB of the power loss. For intermediate SNR channels, a combination of the two schemes is shown to recover both power and shaping losses.     

A Distributed State Estimator Utilizing Synchronized Phasor Measurements

With the creation of balancing authorities by the North American Reliability Council that span large portions of the North American interconnection, and stringent requirements for real time monitoring of power system evolution, faster and more accurate state estimation algorithms that can efficiently handle systems of very large sizes are needed in the present environment. This paper presents a distributed state estimation algorithm suitable for large-scale power systems. Synchronized phasor measurements are applied to aggregate the voltage phase angles of each decomposed subsystem in the distributed state estimation solution. The aggregated state estimation solution is obtained from the distributed solution using a sensitivity analysis based update at chosen boundary buses. Placement of synchronized phasor measurements in the decomposed subsystems is also investigated in this paper. Test results on the IEEE 118-bus test bed are provided     

N,N''-取代邻苯二胺的合成

通过2-取代苯并咪唑盐的还原开环反应制备了8个N,N′-不同取代的邻苯二胺,并经1HNMR、IR、MS及元素分析表征,其中5个未见文献报道.这是一条由邻苯二胺和羧酸经2.取代苯并咪唑制取该类化合物的简洁合成路线.     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

纤维增强复合材料层合圆柱壳的优化设计

本文从中面内承受轴向压力及从垂直于中面内的横向载荷考虑弯曲挠度和自振频率,综合研究了纤维缠绕层合圆柱壳的优化设计。     

一个用户接口管理系统

本文介绍了一个用户接口管理系统NUUIMS的设计和实现.重点叙述了该系统基于规范化目标用户接口模型的设计思想,系统组成及描述方法.文章也讨论了使用NUUIMS设计而成的用户接口的特点.     

基于ARIMA和支撑矢量机组合预测的惯性器件故障预报

文中提出一种基于ARIMA和支撑矢量机进行组合预测的方法,该方法综合运用ARIMA良好的线性拟合能力和支撑矢量机强大的非线性映射功能,将两种预测模型有机地组合在一起,综合各自优点,以期有效改善模型的拟合能力,获得最优预测效果.文中将该方法应用于某飞行器惯性器件的故障预报当中并进行了仿真实验.结果表明,这种方法相对于单项模型的预测具有更高的精度,对于复杂时间序列的分析和预测有很好的应用价值,在故障预报中具有广泛的应用前景.     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

狭小场地条件下大跨度预应力混凝土拱板的运输及吊装

介绍了大跨度预应力混凝土拱板在狭小场地条件下的起模、运输及空间滑移吊装的方法，经在众多中直粮库中的应用，证明该方法简单、适用、经济。