Al,Ga取代Bi：DyIG薄膜的磁和磁光特性的研究

本文报道用热分解法在玻璃衬底上制备了Ａｌ和Ｇａ取代的Ｂｉ：ＤＹＩＧ薄膜，对其磁和磁光特性做了详细研究．Ａｌ和Ｇａ取代的薄膜均可获得好的矩形比和高的矫顽力．对于Ｂｉ１．２Ｄｙ１．８Ｆｅ５－ｘＭＸＯ１２（Ｍ＝Ａ１，ＧＺ）薄膜，Ａ１和Ｇ２的最佳替代成份分别为１．０和Ｇ．７；最佳晶化温度分别为７００ｏ℃和６７５℃．在波长５１０ｎｍ附近，法拉第旋转角可达８°／ｕｍ左右．光学吸收和品质因子的研究结果表明，Ａｌ和Ｇａ取代能够影响光学吸收和品质因子，其中Ｇａ取代对光学吸收和品质因子的影响较大．     

用过滤工艺全面提高铸锭质量

探讨了过滤器孔径对6063铝合金铸锭组织和性能的影响规律。在此基础上指出,在过滤工艺恰当时,不仅可以减少铸锭中的夹杂物,而且可以有效地防止裂纹、羽毛晶等连续铸锭中的常见缺陷。     

Investigation of texture effect on visual colour difference evaluation

The texture effect on visual colour difference evaluation was investigated in this study. Five colour centers were selected and textured colour pairs were generated using scanned textile woven fabrics and colour‐mapping technique. The textured and solid colour pairs were then displayed on a characterized cathode ray tube (CRT) monitor for colour difference evaluation. The colour difference values for the pairs with texture patterns are equal to 5.0 CIELAB units in lightness direction. The texture level was represented by the half‐width of histogram, which is called texture strength in this study. High correlation was found between texture strength and visual colour difference for textured colour pairs, which indicates that an increasing of 10 units of texture strength in luminance would cause a decreasing of 0.25 units visual difference for the five colour centers. The ratio of visual difference between textured and solid colour pairs also indicates a high parametric effect of texture. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 341–347, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.     

Influence of phosphorus element on direct laser sintering of multicomponent Cu-based metal powder

This article presents a detailed investigation on the influence of the phosphorus element upon the laser sintering of a multicomponent Cu-based metal powder system consisting of Cu, Cu-10Sn, and Cu-8.4P. Powder systems containing 0, 10, 15, and 20 wt pct CuP were sintered in atmosphere at room temperature using the following optimal processing parameters: laser power of 350 W, scan speed of 0.04 m/s, scan line spacing of 0.15 mm, and layer thickness of 0.25 mm. It was found that the relative density of the sintered sample with 15 wt pct CuP increased by 24,4 pct as compared with the sample without phosphorus addition. A further increase in the CuP content (≥20 wt pct), however, resulted in a poor densification with a serious delamination. The exact metallurgical roles of the phosphorus element in the laser sintering process were addressed as follows. First, the phosphorus could prevent the sintering system from oxidation by forming CuPO₃, thereby improving the wetting characteristics and the sintering kinetics. Second, the phosphorus could decrease the surface tension of molten materials, leading to a successive transition from highly discontinuous sintered tracks to fairly coherent ones with increasing the phosphorus content. Third, the phosphorus could lower the melt viscosity, thereby improving the microstructural homogeneity of the laser-sintered samples.     

单壁碳纳米管的制备及生长特性研究

采用Fe/MgO作为催化剂 ,催化裂解CH4制备了较纯的单壁碳纳米管 ,用TEM和Raman对碳纳米管进行了表征 ,对不同生长温度下制备的碳纳米管Raman径向呼吸振动峰 (RBM)进行了分析 ,研究了生长温度对单壁碳纳米管生长特性和结构特性的影响     

城市化进程中的小城镇交通初探

通过对小城镇城市结构、路网结构、交通结构和交通管理特征进行详细分析，得出小城镇交通问题症结所在，并初步提出小城镇交通规划和交通治理的对策。     

天铁炼铁技术进步

近十年来，天铁集团炼铁厂通过改善原燃料条件；优化炉料结构，提高入炉品位；采用提高炉顶压力、富氧喷煤、低硅冶炼、炉顶气象系统等多项先进技术，使高炉各项经济技术指标逐年提高。     

A mechanistic analysis of the correlation between overall strength and indentation hardness in discontinuously reinforced aluminum

It is well established that the indentation hardness of metallic alloys shows a reasonable correlation with their yield strength or ultimate strength. Experiments illustrate that such a unique correlation is nonexistent for discontinuously reinforced metal matrix composites, even when the indentation size is much greater than the reinforcement size. For aluminum alloys reinforced with silicon carbide particles, the same composite yield strength and tensile strength with different reinforcement fractions do not lead to similar hardness, or vice versa. Finite element analyses are carried out to rationalize the experimental findings. The modeling utilizes a two-dimensional plane-strain formulation. Discrete particles are included in the material model, and the overall stress-strain response and the indentation response are numerically simulated. The results confirm the lack of unique correspondence between the composite hardness and strength. The alteration of local heterogeneity in the composite is found to affect the indentation response. Effects of the geometrical arrangement of particles and thermal residual stresses on the indentation response are also investigated numerically.     

Design of photonic crystal fibers for dispersion-related applications

A general procedure for design of photonic crystal fibers (PCFs) with desirable dispersion properties is presented. The design model is based on the combination of a rigorous vector mode solver and a scaling transformation for the dispersion properties of the PCFs. In comparison with the conventional design method, the new design procedure is more efficient and can be readily automated for the purpose of design optimization. Several applications of the design procedure, e.g., the design optimization for dispersion shifted fibers, dispersion flattened fibers, and dispersion compensation fibers, are demonstrated and discussed.