Photoreactivation of Escherichia coli following medium-pressure ultraviolet disinfection and its control using chloramination.

Ultraviolet (UV) disinfection is becoming increasingly popular as an alternative disinfection technology to chlorination in recent years. In this study, we investigated the photoreactivation of Escherichia coli following medium-pressure (MP) UV disinfection of synthetic water by a bench-scale collimated beam apparatus. The UV doses ranged from 1.6 -19.7 mWs/cm2 and photoreactivation was investigated for 6 hours under fluorescent light. In addition, chloramination was applied after UV disinfection to investigate its ability to control photoreactivation. It was found that photoreactivation occurred for all UV doses tested and the increase in bacteria numbers ranged from 0.04 to 1.35 log10. However, the degree of photoreactivation decreased with increased UV doses. Chloramination experiments revealed that the addition of 0.5 mg/l of monochloramine resulted in suppression of photoreactivation for 1 hour only. An increased monochloramine dose of 1 mg/l was found to prevent photoreactivation for the entire duration of the experiment. The results of this study have shown that photoreactivation occurs even after MP UV disinfection, although it is of a lesser extent at higher UV doses. This study has also established that secondary chloramination can effectively suppress and eliminate photoreactivation with a chloramine dose of 1 mg/l.     

Programmable group-delay module using binary polarization switching

We demonstrate the first programmable group-delay module based on polarization switching. With a unique binary tuning mechanism, the device can generate any differential group delay value from -45 to +45 ps with a resolution of 1.40 ps, or any true-time-delay value from 0 to 45 ps with a resolution of 0.7 ps. The delay varying speeds for both applications are under 1 ms and can be as fast as 0.1 ms. We evaluate both the dynamic and static performances of the device while paying special attention to its dynamic figures of merit for polarization-mode dispersion emulation and compensation applications. Our experiment shows that the device exhibits a negligible transient-effect induced power penalty (<0.2 dB) in a 10-Gb/s nonreturn-to-zero system.     

Long-wavelength infrared photoinduced switching of a resonanttunneling diode using the intersubband transition

Voltage switching induced by long-wavelength infrared light from a CO₂ laser was observed using a double-barrier resonant tunneling diode (RTD) biased in the bistable region and the intersubband transition (IT) between the quantum confined states. Possible optoelectronic and all-optical switching applications involving hysteresis are proposed and discussed     

Traction-based Completed Adjoint Double Layer Boundary Element Method in elasticity

This paper is concerned with a traction-based Completed Adjoint Double Layer Boundary Element Method to solve for the surface traction of a system of rigid particles embedded in an elastic matrix. The main feature of the method is a single layer representation of the displacement field, which leads to a system of second-kind integral equations for the traction field, the extreme eigenvalue of which could be deflated, allowing iterative solution strategies to be effectively applied. The method is therefore most suitable for large-scale simulations of particulate solids. The method is benchmarked against some known analytic solutions, including the difficult stress singularity problems at sharp edges. The effectiveness of the method in dealing with a large number of inclusions is also demonstrated with an elongational deformation problem involving up to 25 inclusions.Research supported by the Australian Research Council (to NP-T and X-JF) and the National Natural Science Foundation of China (X-JF).     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Robustness of VS-MRAC with respect to unmodelled dynamics and external disturbances

A variable structure model reference adaptive controller (VS-MRAC) using only input and output measurements was recently proposed and shown to be globally asymptotically stable with superior transient behaviour and disturbance rejection properties. In this paper a singular perturbation approach is used in order to establish the robustness of the controller in the presence of unmodelled dynamics (parasitics) and disturbances. We develop a new Lyapunov-based technique to analyse the overall system and show that for sufficiently small parasitics the system remains stable and the output error is small in some sense.     

Supporting real-time and multimedia applications on the Mercuritestbed

This paper describes the distributed system, network and software architecture, the application development environment, the performance, and the early lessons learned on the ATM LAN testbed Mercuri established at the Honeywell Technology Center, to develop distributed multimedia technologies for real-time control applications. We have developed a client-server-based software architecture on Sun Sparcstation-2s connected by a Fore Systems' ASX-100 ATM switch, with video processing handled by Parallax's X Video cards. The architecture enables network-transparent applications and provides simple primitives for multimedia capture, display, transmission, storage, and retrieval. A real-time multimedia-in-the-loop control application was developed as the vehicle for testing the capabilities and performance of the network. Our test measurements focus on the end-user-level performance metrics such as message throughput and round-trip delay as well as video-frame jitter under no-load and load conditions. Our results show that the maximum burst throughput that can be supported at the user level is 48 Mb/s using AAL 5, while round-trip delays for 4-kbyte messages are about 3 ms. Our experience reveals a number of performance bottlenecks and open issues in using commercial ATM switches for practical applications. Our conclusions are outlined