An integrated air-gap-capacitor pressure sensor and digital readoutwith sub-100 attofarad resolution

The fabrication and characterization of an integrated air-gap-capacitor pressure sensor are presented. The capacitor fabrication process uses standard IC processing to create NMOS circuits, and an added polysilicon layer to create poly-to-n⁺ capacitors with a 0.6-μm-thick dielectric using deposited oxide. Subsequent processing is used to produce deformable, parallel-plate, air-gap capacitors on the front side alongside MOS circuits. Sensor chips are fabricated using 100-μm×100-μm, 100-fF air-gap capacitors with on-chip circuitry. The sensor chip is a part of a capacitive measurement system that uses a charge-redistribution sense technique to achieve very high capacitance resolution. The behavior of the pressure sensor chips was studied as a function of applied pressure in the 0-240-kPa (0-35-psi) range. Measurements indicate a sensitivity of 0.93 mV/kPa (6.40 mV/psi) with a deflection of 10 nm/kPa (70 nm/psi) at 0-69 kPa (0-10 psi). Standard deviations indicate a static pressure resolution of 0.54 kPa (0.078 psi), which translates to 30 attofarads at a sampling frequency of 11 kHz     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

A model for the seismic reliability assessment of electric power transmission systems

A comprehensive model to evaluate the seismic reliability of electric power transmission systems is presented. The model provides information on the probability of structural failure of critical equipment at the major substations, from which the corresponding probabilities of power disruption to a given service area are determined. With the proposed methodology earthquake ground motions are defined as stochastic processes, and seismic capacities of electrical equipment are determined on the basis of available test data and simple modeling, from which fragility functions of critical equipment and specific substations are developed. Probabilities of power disruption resulting from network disconnectivity and abnormal power flow are assessed through Monte Carlo simulation. As a case study, the proposed model is applied to the electric power network in San Francisco and vicinity under the 1989 Loma Prieta earthquake, and the probabilities of power interruption are contrasted with the actual power failures observed during that earthquake.     

Evaluation of Soybean Seedcoat Cracking During Drying:PART II. Using MRI

MRI techniques were developed and employed for non-destructive and noninvasive study of seedcoat cracking in low moisture soybean kernels during heated air drying. Proton density image and transient moisture distribution profile of a single soybean kernel can be obtained using MRI. These MRI techniques proved to be particularly useful for the continuous observation of initiation and propagation of seedcoat cracking during the entire period of drying process without interruption.

The proton density images of soybean kernels showed that seedcoat cracking was initiated perpendicular to the long axis of the kernel near the hilum. The transient moisture distribution profiles in soybean kernels during drying indicate that moisture gradient developed during drying was higher in the seedcoat than in the cotyledon. Drying temperature and initial average moisture content were positively correlated with the soyhean seedcoat crackig. The location of the