Mutual information-based analysis of JPEG2000 contexts.

Context-based arithmetic coding has been widely adopted in image and video compression and is a key component of the new JPEG2000 image compression standard. In this paper, the contexts used in JPEG2000 are analyzed using the mutual information, which is closely related to the compression performance. We first show that, when combining the contexts, the mutual information between the contexts and the encoded data will decrease unless the conditional probability distributions of the combined contexts are the same. Given I, the initial number of contexts, and F, the final desired number of contexts, there are S(I, F) possible context classification schemes where S(I, F) is called the Stirling number of the second kind. The optimal classification scheme is the one that gives the maximum mutual information. Instead of using an exhaustive search, the optimal classification scheme can be obtained through a modified generalized Lloyd algorithm with the relative entropy as the distortion metric. For binary arithmetic coding, the search complexity can be reduced by using dynamic programming. Our experimental results show that the JPEG2000 contexts capture the correlations among the wavelet coefficients very well. At the same time, the number of contexts used as part of the standard can be reduced without loss in the coding performance.     

利用铝（100）面隧道孔制备纳米模板及有序阵列材料

高纯铝箔通常通过电化学扩面后用作铝电解电容器的阳极材料。利用铝箔（100）面隧道孔制备纳米模板。这种纳米模板的特点是制作简单、模板面积大，纳米阵列材料形状可控性强。还利用两步电化学侵蚀铝箔的特殊工艺，研制出纵横交错的TiO2纳米有序阵列材料。     

铁素体球墨铸铁与20钢的闪光对焊

试验使用铁素体球墨铸铁和20钢的实心棒料进行了闪光对焊，通过改变次级电压4～8级，通电时间3～5s，观察其焊接接头组织的变化并测定其抗拉强度。结果表明，接头由三个区组成；当通电时间一定时，抗拉强度随次级电压的升高先减小后增大；当次级电压一定时，抗拉强度随通电时间的增加而增大。在次级电压为8级、通电时间为5s时，抗拉强度达最大值，为370．8MPa，是20钢母材的90.4％，是球墨铸铁母材的83.7％。     

靶向抗癌药格列卫与其治疗白血病疗效监测

Gleevec是抑制致癌的融合蛋白BCR-ABL的一种分子靶向治疗药物,BCR-ABL是一种与慢性髓细胞性白血病(CML)有关的酪氨酸激酶抑制剂。用Gleevec选择性地抑制BCR-ABL活性在治疗CML中显示出很好的效果,特别是在CML慢性期,因此,监测疗效非常重要。现就Gleevec的研究进展及如何监测其在CML中的疗效作一简单综述。     

汽轮机叶片用X20Cr13钢的热处理工艺研究

采用正交试验对汽轮机叶片用X20Cr13钢进行了热处理工艺研究，以获得该钢的最佳热处理工艺，并在回火后以不同的速度冷却，以揭示冷却速度对钢的回火脆性的影响。结果，X20Cr13钢的最佳热处理工艺为900℃油淬或风冷，670℃回火，风冷。     

Realization of Tapered Waveguide by Stretching the Rod Waveguide

By stretching the rod waveguide with different velocities in opposite directions, the tapered waveguide can be fabricated. In condition of taking no account of volume expansion caused by heating and under the assumptions of volume conservation,the rod waveguide can be stretched freely in the heated region without being stretched outside of the heated region. A model,which shows the relation of the transition shape and the two factors, that is the ratio of two velocity and the heated region length, is presented for the shape of the taper transition through mathematic deduction. Based on this model, a desired tapered waveguide can be fabricated. The tapered waveguide are widely used for fabricating tapered fiber couplers and sensors. In addition, the conclusion can be used for fabricating fused fiber coupler.     

一种基于bit位的运动补偿方法

本文讨论了等离子体显示屏所特有的在显示运动画面时出现的伪轮廓线现象，对产生的原因进行了分析并给出了软件模拟的结果。在此基础上，提出了一种基于bit位的运动补偿方法来改善运动图像的画面质量，同时根据人眼的视觉特征对补偿方法做了进一步的优化。最后对基于bit位的运动补偿方法进行了比较和验证，结果表明基于bit位的运动补偿方法可以基本消除运动画面的伪轮廓线现象。     

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (<-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.     

一种前馈型全摆幅恒跨导准恒增益CMOS运放设计

设计了一种适合在低电源电压下工作的前馈型输入级放大结构，在全摆幅的动态工作范围内，输入级跨导保持不变，采用负载电流补偿以保证增益近似恒定，输出采用前馈型AB类输结构，实现全摆幅输出。     

以寻呼区分析为基础的PHS网络优化方法

通过分析PHS网络中各寻呼区的统计指标,剖析指标劣化的根本原因,采取修改相应的参数配置、移站、调整天线等措施进行网络优化,优化实施后再次收集统计指标做对比分析,总结经验。