螺旋搅龙加工新方法

螺旋搅龙是联合收割机的重要零件之一。按照传统的加工方法，由若干件单片焊接而成。因此种方法需要几套冲压工装，经落料、冲孔、切角等工序，以至材料利用率很低；且再经数片接焊工序后，变形突出，表面粗糙。造成零件制作成本较大。考虑到传统工艺的弊端，研究在普通车床上采用一套工装用条料绕成螺旋搅龙的新方法。经过反复试验获得成功。与传统的加工方法相比，材料节约37％。大大降低了产品成本，提高了产品质量和生产效率。     

BOPP薄膜生产中的功能母料

简述了BOPP薄膜生产过程中所需要的抗静电母料、防粘连母料和爽滑母料等功能母料，并分析了它们的作用、机理以及在生产中的应用特点。     

Microfabricated needle-type sensors for pO/sub 2/, pCO/sub 2/, and pH

In order to conduct in vivo continuous monitoring of blood gas levels, very thin disposable pO/sub 2/, pCO/sub 2/, and pH sensors, which could be incorporated into a syringe needle or a catheter, were microfabricated. Electrode patterns were formed on a polyimide substrate and stacked with intervening polyimide insulating layers. An electrolyte layer was formed, which was covered with a silicone rubber gas-permeable membrane or a passivating layer. The most critical part of the sensor was a Ag-AgCl reference electrode with a pinhole structure. Because of the structure and novel operational mode of the reference electrode, its potential stabilized immediately, and reproducible responses were realized for the respective sensors. Performance characterization revealed clear responses and linear calibration plots in the ranges of partial pressures or pH of physiological levels. No significant damages or changes in the performance of the sensors were observed after ethylene oxide sterilization.     

Performance of a combined eco-system of ponds and constructed wetlands for wastewater reclamation and reuse.

An on-site study on the operational performance of a combined eco-system of ponds and SF constructed wetland for municipal wastewater treatment and reclamation/reuse in Donging City, Shandong, China was carried out from January 2001 through October 2003. The removal efficiencies for various main parameters were: TSS 84.8 +/- 7.3%, BOD5 87.2 +/- 5.3%, CODCr 70.2 +/- 18.6%, TP 52.3 +/- 23.1%, and NH(3)-N 54.8 +/- 23.9% with effluent concentration of TSS 9.12 +/- 5.12 mg/l, BOD5 6.44 +/- 4.58 mg/l, CODCr, 42.8 +/- 6.7 mg/l, TP 0.94 +/- 0.27 mg/l and NH(3)-N 7.95 +/- 2.36 mg/l. In addition, the removal efficiencies for faecal coliforms and total bacteria were > 99.97% and > 99.998% respectively, which well meet Chinese National standards for effluent quality of municipal wastewater treatment plants. The composition of TSS was closely related to CODCr and BOD5 variations, and nitrification-denitrification is the major mechanism of nitrogen removal both in ponds and in wetlands. In addition, sedimentation also played an important role in the removal of TSS, nitrogen, phosphorus and BOD5. The removal efficiencies of various parameters, the number of species and biomass of biological community in the system increased gradually with the ecological maturation.     

A 4-MB on-chip L2 cache for a 90-nm 1.6-GHz 64-bit microprocessor

A 4-MB L2 data cache was implemented for a 64-bit 1.6-GHz SPARC(r) RISC microprocessor. Static sense amplifiers were used in the SRAM arrays and for global data repeaters, resulting in robust and flexible timing operation. Elimination of the global clock grid over the SRAM array saves power, enabled by combining the clock information with array select signals. Redundancy was implemented flexibly, with shift circuits outside the main data array for area efficiency. The chip integrates 315 million transistors and uses an 8-metal-layer 90-nm CMOS process.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Application of Direct Ignition Technology with Minimum Gasified Oil in Lignite-Fired Boiler

The firing is in the stable condition and the rate of oil saving comes up to 64%, after Fularji Power Plant adopted the technology of minimum gasified oil igniting pulverized lignite directly and the technology of multistage coal combustion with energy amplified stage by stage.     

非标准工况下空分设备增产氩的研究与实践

文章对非标准工况下的空分设备增产氩措施进行了研究。以宝钢6#60000m3/h空分设备为例,通过设计型算法和校核型算法,建立了空分设备精馏的数学模型,通过改变数学模型的参数,分析了在非标准工况下精馏塔内的组分浓度分布,并提出了优化后的操作方案和操作参数,实施后提高了空分设备的氩提取率,取得了显著的经济效益。