Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Investigation of Mechanical and Electrical Characteristics for Cracked Conductive Particle in Anisotropic Conductive Adhesive (ACA) Assembly

In an anisotropic conductive adhesive (ACA) assembly, the electrical conduction is usually achieved with the conductive particles between the bumps of integrated circuit (IC) and corresponding conductive tracks on the glass substrate. Fully understanding of the mechanical and electrical characteristics of ACA particles can help to optimize the assembly process and improve the reliability of ACA interconnection. Most conductive particles used in the ACA assembly are with cracks in the metal coating of the particles after the ACA bonding. This paper introduced the fracture analysis by applying the cohesive elements in the numerical model of the nickel-coated polymer particle and further simulating the cracks initiation and propagation in the nickel coating during the ACA bonding. The simulation results showed that the stress distribution on the nickel-coated particle with cracks was significantly different from that on the nickel-coated particle without crack, indicating that the stress analysis by taking the crack into consideration is very important for the reliability assessment of the ACA interconnection. The stress analysis of cohesive elements indicated that the cracks initiated at the central area of the nickel coating and propagated to the polar area. Furthermore, by the introduction of a new parameter of the virtual resistance, a mathematical model was established to describe the electrical characteristics of the nickel-coated particle with cracks. The particle resistance of the nickel-coated particle with cracks was found to be much higher than that of the particle without crack in the optimized bonding pressure range, indicating that it is necessary to take the crack into consideration for the particle conduction analysis as well. Therefore, the fracture analysis on the conductive particle by taking the crack into consideration could accurately evaluate the reliability of ACA interconnection and avoid serious reliability issues.     

镁钴铝类水滑石催化合成安息香甲醚

采用共沉淀法制备了镁钴铝类水滑石化合物(MgCoAl-HTLcs),并用 X 射线衍射、扫描电子显微镜、NH_3程序升温脱附等方法对 MgCoAl-HTLcs 进行了表征,并以 MgCoAl-HTLcs 为催化剂催化苯甲醛与甲醇反应合成安息香甲醚,研究了n(Mg):n(Co):n(Al)、催化剂用量、原料配比、反应温度、反应时间对合成反应的影响。表征结果显示,MgCoAl-HTLcs 的晶相完整,表面主要为弱酸、弱碱性。催化合成安息香甲醚的适宜条件为:MgCoAl-HTLcs 催化剂用量0.10 g(约为原料总质量的0.23%),n(Mg):n(Co):n(Al)=0.4:1.6:1.0,V(苯甲醛):V(甲醇)=3:50,反应温度50℃,反应时间150 min。在此条件下,苯甲醛的平衡转化率达77.49%,安息香甲醚选择性接近100%。为洁净合成安息香甲醚开辟了一条新的途径。     

Optimal and self‐tuning fusion Kalman filters for discrete‐time stochastic singular systems

Based on the optimal fusion estimation algorithm weighted by scalars in the linear minimum variance sense, a distributed optimal fusion Kalman filter weighted by scalars is presented for discrete‐time stochastic singular systems with multiple sensors and correlated noises. A cross‐covariance matrix of filtering errors between any two sensors is derived. When the noise statistical information is unknown, a distributed identification approach is presented based on correlation functions and the weighted average method. Further, a distributed self‐tuning fusion filter is given, which includes two stage fusions where the first‐stage fusion is used to identify the noise covariance and the second‐stage fusion is used to obtain the fusion state filter. A simulation verifies the effectiveness of the proposed algorithm. Copyright © 2008 John Wiley & Sons, Ltd.     

B737机务CBT系统建设方案的探讨

通过对AICC制订的CBT课件开发规范的探讨，阐述了CBT的基本概念和波音737飞机机务CBT的开发制作过程，以及利用Authorware开发软件制作多媒体课件的技术难点。     

A Tutorial on GrÖbner Bases With Applications in Signals and Systems

This paper is a tutorial on GrÖbner bases and a survey on the applications of GrÖbner bases in the broad field of signals and systems. A reasonably detailed review is given of several fundamental theoretical issues that occur in the use of GrÖbner bases in multidimensional signals and systems applications. These topics include the primeness of multivariate polynomial matrices, multivariate unimodular polynomial matrix completion, and prime factorization of multivariate polynomial matrices. A brief review is also presented on the wide-ranging applications of GrÖbner bases in multidimensional as well as one-dimensional circuits, networks, control, coding, signals, and systems and other related areas like robotics and applied mechanics. The impact and scope of GrÖbner bases in signals and systems are highlighted with respect to what has already been accomplished as a stepping stone to expanding future research.      

Power Distribution Fault Cause Identification With Imbalanced Data Using the Data Mining-Based Fuzzy Classification E-Algorithm

Power distribution systems have been significantly affected by many outage-causing events. Good fault cause identification can help expedite the restoration procedure and improve the system reliability. However, the data imbalance issue in many real-world data sets often degrades the fault cause identification performance. In this paper, the E-algorithm, which is extended from the fuzzy classification algorithm by Ishibuchi to alleviate the effect of imbalanced data constitution, is applied to Duke Energy outage data for distribution fault cause identification. Three major outage causes (tree, animal, and lightning) are used as prototypes. The performance of E-algorithm on real-world imbalanced data is compared with artificial neural network. The results show that the E-algorithm can greatly improve the performance when the data are imbalanced     

Note on ‘Construction of Double Sampling s‐Control Charts for Agile Manufacturing’

He and Grigoryan (Quality and Reliability Engineering International 2002; 18 :343–355) formulated the design of a double‐sampling (DS) s control chart as an optimization problem and solved it with a genetic algorithm. They concluded that the DS s control charts can be a more economically preferable alternative in detecting small shifts than traditional s control charts. We explain that, since they only considered the average sample size when the process is in control, their conclusion is questionable. Copyright © 2006 John Wiley & Sons, Ltd.