300 m级高拱坝设计与施工三维可视化仿真研究

双曲拱坝的C2连续曲面的三维模型表达困难,以双曲拱坝函数方程为基础引入CATIA三维软件,实现交互式设计和分析。同时,完成双曲拱坝细部模型的基于规则的智能化设计。基于大坝详细设计的三维成果,利用组件技术对模型数据进行提取和利用,制定施工方案并进行施工方案的动态可视化仿真。     

基于手写笔的多功能电子白板系统的实现

该文针对当前电子白板系统对个性化支持的不足,引入手写笔作为输入设备,充分利用其功能参数,设计开发了具有模拟毛笔、钢笔、铅笔等真实笔特征的多笔型功能的电子白板系统。     

涤纶工业丝环吹风改造的设计计算

应用PET纤维的冷却成形理论 ,结合空气调节的相关知识 ,提出了环吹风的设计计算方法 ,对涤纶工业丝环吹风进行了设计改造 ,满足了纺丝工艺要求     

热声制冷机及其改进实验研究

热声制冷作为一种很有前途的制冷方法，在国内外相关领域引起了极大兴趣。热声制冷机由声发生器、共振管、板叠及高、低温换热器等部分组成。对声驱动器的振动膜及其冷却系统、气体弹簧系统、高、低温换热器进行了初步改进，使制冷机冷端温降从原来的12℃提高到27℃左右，这是目前国内报道的最大温降。     

半导体量子点中极化子的有效质量

研究了半导体量子点中极化子的有效质量.采用改进的线性组合算符方法,导出在电子-体纵光学声子(LO)强耦合时抛物量子点中极化子的振动频率、相互作用能和有效质量随受限强度和电子-声子耦合强度的变化.对RbCl晶体量子点进行了数值计算,结果表明,量子点受限越强,半导体量子点中强耦合极化子的振动频率和有效质量就越大;极化子的相互作用能随受限强度的增加先急剧增加,当达到极值后,随受限强度的增加而急剧减少     

锂离子电池用聚合物电解质的最新进展II.含液聚合物电解质

由于干态聚合物电解质目前还不能满足聚合物锂离子电池的应用要求,人们致力于开发含液体增塑剂的聚合物电解质,包括凝胶型和微孔型两类体系。本文综述了含液聚合物电解质的最新进展,重点论述了各种新体系和新方法。     

End‐Capping as a Method for Improving Carrier Injection in Electrophosphorescent Light‐Emitting Diodes

The electronic properties, carrier injection, and transport into poly(9,9‐dioctylfluorene) (PFO), PFO end‐capped with hole‐transporting moieties (HTM), PFO–HTM, and PFO end‐capped with electron‐transporting moieties (ETM), PFO–ETM, were investigated. The data demonstrate that charge injection and transport can be tuned by end‐capping with HTM and ETM, without significantly altering the electronic properties of the conjugated backbone. End‐capping with ETM resulted in more closely balanced charge injection and transport. Single‐layer electrophosphorescent light‐emitting diodes (LEDs), fabricated from PFO, PFO–HTM and PFO–ETM as hosts and tris[2,5‐bis‐2′‐(9′,9′‐dihexylfluorene)pyridine‐κ²NC_3′]iridium(III ), Ir(HFP)₃ as the guest, emitted red light with brightnesses of 2040 cd m^–2, 1940 cd m^–2 and 2490 cd m^–2 at 290 mA cm^–2 (16 V) and with luminance efficiencies of 1.4 cd A^–1, 1.4 cd A^–1 and 1.8 cd A^–1 at 4.5 mA cm^–2 for PFO, PFO–HTM, and PFO–ETM, respectively.     

Modeling of a constant Voltage transformer

This paper presents a comprehensive nonlinear model of the controlled constant voltage transformer also known as the ferroresonant transformer. Saturation is a normal mode of operation for this device. This paper derives an equivalent electrical circuit that relates to the physical structure of a typical design. The level of detail includes winding resistances, continuously nonlinear magnetizing inductances, tapped windings, and leakage inductances. The paper describes methods to extract the winding resistances, leakage inductances, and hysteresis loops of the transformer and how to fit the latter into single-valued nonlinear functions. The paper compares computer simulation results of the model with those obtained analytically and experimentally. The results show that the derived circuit will be very useful for designers of the ferroresonant transformer, which is used in uninterruptible power supplies.     

射孔枪+内置式压力计托筒+水力泵新三联作试油(测试)工艺技术在大港油田研制与应用

该工艺技术是在原三联作(TCP+MFE+JET)基础上,根据大港油田勘探试油(测试)的需要,研制开发出的又一新技术,与原三联作相比,一趟管柱不但完成求产、测压、泵排工作,而且还能进行酸化等措施,提高了资料品质,减少了作业成本。经过6井次现场应用,全部达到了设计要求,取得了工艺、资料、成本、速度的较大进步,具有较高推广应用价值。