烧成及热处理工艺对钛酸锶铅基热敏材料性能及显微结构的影响

研究了烧成及热处理工艺对钛酸锶铅基热敏材料的阻温特性及显微结构的影响。通过扫描电镜（ＳＥＭ）和能量分散仪（ＥＤＡＸ）分析了材料的显微结构及不同形貌晶粒的成份。通过对组成、烧成及热处理工艺的控制，可得到具有Ｖ型ＰＴＣＲ特性的热敏材料。     

吸附制冷循环的热力计算及热力学评价方法探讨

在化工吸附，吸附热力学及Polanyi吸附位势理论的基础上，介绍吸附制冷基本型循环，推演其参数坐标图，进而分析，给出其主要性能指标的热力计算，然后以热力学的逆卡诺循环和内可逆三热源循环模型为指针，对此制冷循环进行考察。并结合热力计算对其热力学完善性做出评价，从而给出了吸附制冷基本型循环合适的热力学评价方法。     

碾压混凝土坝施工进度与质量控制的新措施

碾压混凝土重力坝和拱坝由于连续施工的坝体混凝土体积大，施工期间需要采取较为严格的温度控制措施，而所采取的温控措施是否有效，目前尚没有一个能够用于实际施工过程的快速有效的评估方法和方式，不能根据已施工坝体内的实际情况来控制施工进度和质量。利用分布式光纤温度测量系统来快速地获得坝体混凝土内部的大量温度信息，进而实际标定温度仿真程序并通过标定过程模拟拟施工的连续碾压层，以检验其温控措施的有效性。通过坝体内部的温度、温度变化速率和梯度来达到实时控制坝体碾压上升速度、坝面和仓面养护、以及冷缝灌浆处理等目的。     

木犀科植物花粉的扫描电镜研究

植物花粉的形态特征具有种属特异性。本文用扫描电子显微镜观察了木犀科(Oleaceae)的六属八种植物花粉的形态特征。结果表明,除迎春有个别四萌发沟外,其它花粉都是三沟型,外壁纹饰均为网状。但各种植物花粉的细微形态仍有明显差异。因此,用扫描电镜观察研究植物花粉的亚微形态特征,可为植物分类提供一些必要的形态依据。     

Simulation study of peak junction temperature and power limitationof AlGaAs/GaAs HBTs under pulsed and CW operation

The authors have used a 3-D transmission-line matrix (TLM) modeling method to study the junction temperature distribution and power limitation of device geometries with multiple embedded heat sources. Peak values of the junction temperature against the dissipated power density under both pulsed and CW operation are presented for a typical power AlGaAs/GaAs HBT structure. These data should facilitate the rapid determination of junction temperature for a given output power, which is of paramount importance in power device design     

脉冲啁啾对干涉相关测宽的影响及其消除方法

本文深入讨论了脉冲啁啾的非线性起源及其对干涉相关测宽(等值宽度和条纹计数)法的影响。提出根据干涉相关曲线下包络最大值位置适当降低等值宽度位置和用计算机平均处理干涉相关信息的技术以消除啁啾的影响。     

对HIC试验中两种不同腐蚀介质酸碱度的探讨

HIC是腐蚀试验中常用的检测方法,用来测评材料在含硫化氢环境中对氢离子敏感性大小.其包含两种不同的腐蚀介质,不同的腐蚀介质中酸碱度是不一样的,腐蚀介质的酸碱度对试验结果有较大的影响,为此,运用电离平衡理论,计算并分析两种不同腐蚀介质电离平衡前后的氢离子浓度变化,得出动态反应平衡时氢离子浓度的关系式,从而获得介质中精确的氢离子浓度,并对腐蚀介质中相关离子进行了探讨,为进一步探究相关环境中的腐蚀机理提供了依据.     

Evaluation of constructed wetlands by wastewater purification ability and greenhouse gas emissions.

Domestic wastewater is a significant source of nitrogen and phosphorus, which cause lake eutrophication. Among the wastewater treatment technologies, constructed wetlands are a promising low-cost means of treating point and diffuse sources of domestic wastewater in rural areas. However, the sustainable operation of constructed wetland treatment systems depends upon a high rate conversion of organic and nitrogenous loading into their metabolic gaseous end products, such as N2O and CH4. In this study, we examined and compared the performance of three typical types of constructed wetlands: Free Water Surface (FWS), Subsurface Flow (SF) and Vertical Flow (VF) wetlands. Pollutant removal efficiency and N2O and CH4 emissions were assessed as measures of performance. We found that the pollutant removal rates and gas emissions measured in the wetlands exhibited clear seasonal changes, and these changes were closely associated with plant growth. VF wetlands exhibited stable removal of organic pollutants and NH3-N throughout the experiment regardless of season and showed great potential for CH4 adsorption. SF wetlands showed preferable T-N removal performance and a lower risk of greenhouse gas emissions than FWS wetlands. Soil oxidation reduction potential (ORP) analysis revealed that water flow structure and plant growth influenced constructed wetland oxygen transfer, and these variations resulted in seasonal changes of ORP distribution inside wetlands that were accompanied by fluctuations in pollutant removal and greenhouse gas emissions.     

自干扰抵消盲空时DS-CDMA信号检测技术

针对传统单用户检测器存在远近效应和性能下界问题,近年来提出的一系列最大SINR准则盲空时RAKE接收机,可以较好地合并期望用户的多径分量,同时抑制多址干扰用户能量.本文对这类接收机进行了进一步的研究,提出了一种自干扰抵消方法,更有效地克服了单用户检测器存在的性能下界以及远近效应问题.仿真结果验证了本文方法的有效性.     

喷墨打印机的使用与维护

介绍使用喷墨打印机应注意的事项，探讨打印机墨水消耗过快的问题。