p-moment stability of stochastic impulsive differential equations and its application in impulsive control

The exponential p-moment stability of stochastic impulsive differential equations is addressed. A new theorem to ensure the p-moment stability is established for the trivial solution of the stochastic impulsive differential system. As an application of the theorem proposed, the problem of controlling chaos of Lorenz system which is excited by parameter white-noise excitation is considered using impulsive control method. Finally, numerical simulation results are given to verify the feasibility of our approach. Supported by the National Natural Science Foundation of China (Grant No. 10772046)     

多路输出反激式开关电源的改进与实现

针对传统开关电源存在的控制芯片供电方式耗能较大、反馈电路光耦有效输入电流范围窄两个问题,对传统电源电路进行了改进,设计并实现了一款性能优良的48V转+5V、±15V,输出功率25W的三路输出反激式开关电源。样机输出电压精度为0.2%(+5V)、0.53%(+15V)、0.6%(-15V),输出电压纹波为20mV(+5V)、50mV(+15V)、60mV(-15V),电压精度和纹波率均满足小于1%的要求;测试表明:该电源性能优良,具有效率高,稳压精度高,负载调整率高等优点,有很高的生产应用价值。     

高校智慧实验室综合管理平台建设研究

提出智慧实验室综合管理平台应能改善甚至解决高校实验室存在的人工管理、智慧化建设缓慢、开放共享不足等问题.分析智慧实验室管理平台的架构,描述了管理平台中实验教学管理与实验室开放管理应具备的主要功能与管理流程,为智慧实验室的管理与建设提供一定的参考.     

高性能MCU的FPGA原型验证系统研究与平台实现

本文研究并实现了一种基于Cortex-A7核的高性能MCU在FPGA原型阶段的验证平台。该设计研究可以针对高性能MCU芯片或其FPGA原型验证阶段的软硬件验证环境快速搭建,通过交互式、软硬件协同的方式对MCU芯片各个模块功能进行实时、可靠的功能验证。高效的FPGA原型验证可以提高MCU研发速度、缩短验证时间、提高验证效率、及时发现芯片设计的缺陷、缩短芯片研发周期。     

基于稳健设计的SGNS算法的超参数调优方法

通常给定超参数的若干取值选取性能最大的为最优组合(称为直接选优法),但是此方法的稳健性差。为此,提出了一种基于稳健设计的超参数调优方法(称为稳健调优法)。具体地,以SGNS算法中的超参数调优为例,在词语推断任务上实验并得出:经方差分析得到SGNS算法中的七个超参数中的五个对算法预测性能有显著影响,确定为主控因子,其余两个确定为噪声因子,且主控因子中有三个对性能估计的方差有显著影响,因此,调优中仅从期望最大来直接选优是不合理的;稳健调优法与直接选优法两者在预测性能上没有显著差异,但稳健调优法对噪声因子具有较好的稳健性。稳健调优法对一般的深度神经网络的调参有实际的借鉴意义。     

Enhancement of the hydrogen storage properties of Mg/C nanocomposites prepared by reactive milling with molybdenum

The effect of Mo on the morphology, crystal structure and hydrogen sorption properties of Mg/C composites prepared by reactive milling was studied. Transmission electron microscopic(TEM) observation shows that Mg/C composites prepared with the addition of Mo are of nanoscale with particle size about 20-120 nm after 3 h of milling under 1 MPaH_2. MgH_2 of tetrahedral crystal structure predominates in the materials with the geometric shape of oblique hexagonal prism. From X-ray diffraction(XRD) and hydrogen content studies, Mo and crystallitic carbon have a synergistic effect on promoting the hydrogenation rate in the reactive milling process. From differential scanning calorimetric(DSC) studies, the dehydrogenation peak temperature of the Mg/C materials with Mo is lowered to 299-340 ℃.     

PVA纤维对混凝土抗裂性能的影响研究

针对锦屏二级水电站引水隧洞末端的4个调压井,通过掺入不同掺量的PVA纤维进行混凝土的开裂性能试验研究,得出PVA混凝土最佳纤维掺量为0.9%的结果。在此基础上,探讨了PVA纤维混凝土的配合比,提出了施工现场泵送适应性建议。     

柴油机自动减压起动装置的有限元分析

分析了柴油机自动减压装置的工作原理,针对在潍柴WP10型柴油机上加装的减压装置,利用Solidworks Simulation对压板进行了静力分析,找出了应力最大的部位和最大值,并按照Von Mises准则,判别压板满足刚度要求。     

由恒流二极管串联分压组成的直流辅助电源

设计了一种由恒流模块和稳压模块串联组成的直流辅助电源。介绍了直流辅助电源电路的工作原理,并设计了由恒流模块和稳压模块串联组成的直流辅助电源样机,测试了样机在电网电压波动及负载变化时的输出电压情况。测试结果表明:接入220 V交流电源时,样机可以稳定输出12 V电压,其性能满足设计要求。     

Morphology,crystal structure and hydration of calcined and modified anhydrite

The effects of calcination and modification on the morphology （shapes and textures） and crystal structure of anhydrite powders were studied. The results show that, calcination at 100℃ causes anhydrite to disintegrate into smaller crystals, accompanied by a slight in- crease in d-spacing. Without calcination and modification, the solidification time and curing time of anhydrite are 15 and 77 h, respectively. After the treatment, however, the solidification time and curing time are shortened significantly to 9.5 and 14 rain, respectively. The com- pressive and flexural strengths of hydration products made from the treated anhydrite reach 10.2 and 2.0 MPa, respectively. The much shorter solidification and curing time make it possible to use anhydrite as a building and construction material.