Effects of Ultrasonic Vibration on Material Flow and Thermal Cycles in Friction Stir Welding of Dissimilar Al/Mg Alloys

Comparative experiments are performed in friction stir welding (FSW) of dissimilar Al/Mg alloys with and without assistance of ultrasonic vibration. Metallographic characterization of the welds at transverse cross sections reveals that ultrasonic vibration induces differences in plastic material flow in two conditions. In FSW, the plastic material in the peripheral area of shoulder-affected zone (SAZ) tends to flow downward because of the weakening of the driving force of the shoulder, and a plastic material insulation layer is formed at the SAZ edge. When ultrasonic vibration is exerted, the stirred zone is divided into the inner and outer shear layers, the downward material flow trend of the inner shear layer disappears and tends to flow upward, and the onion-ring structure caused by the swirl motion is avoided in the pin-affected zone. By improving the flow behavior of plastic materials in the stirred zone, ultrasonic vibration reduces the heat generation, accelerates the heat dissipation in nugget zone and changes the thermal cycles, thus inhibiting the formation of intermetallic compound layers.

     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

Analysis of the central cavity of axisymmetric forward extrusion by the upper bound approach

In this paper, the use of a kinematically admissible velocity field to predict the presence of a central cavity in the final stage of axisymmetric forward extrusion is advanced, in accordance with the results of Moire experiments. On the basis of the velocity field, the critical condition for central cavity formation is obtained by the upper bound approach. Furthermore, the quantitative relationships between central cavity formation and process parameters (reduction in area, frictional factors on the ram and chamber wall, relative residual thickness of the of the billet) are studied. The results show that (1) the critical relative residual thickness of the billet used for the central cavity formation is affected primarily by the reduction in area and the frictional factors on the ram, and slightly by the frictional factor on the chamber wall; (2) the relative dimensions of the central cavity increase with a decrease in the relative residual thickness of the billet; (3) the growth rate of the central cavity decreases with an increase in the frictional factors on the ram, but is affected by the frictional factors on the chamber wall only slightly. Good correlation is found between the analytical and experimental results.     

玻璃纤维毡增强热塑性复合片材的研制和应用

本文简要介绍了玻璃纤维毡增强聚丙烯片材的研制，性能和应用。     

打火机专用SAN树脂工业化开发生产

介绍了15kt/a本体苯乙烯－丙烯腈（SAN)装置试生产打火机专用SAN树脂的生产情况，确定了主要工艺配方及参数：进料组成为乙苯浓度为6％－11％、丙烯腈浓度为30％－42％，聚合温度130－145℃、压力0．40－0．46MPa，搅拌转速60－90r/min，脱挥温度215－250℃、压力小于等于4kPa；并对影响打火机志用SAN树脂性能的主要工艺条件及因素进行了讨论。结果表明，聚合温度、结合丙烯腈含量、熔体流动指数、转化率是影响打火机专用SAN树脂生产工艺及产品性能的主要因素。     

细胞激动素Kinetin合成的改进

介绍了用糠胺与腺嘌呤在催化条件下反应合成细胞激动素kinetin,该法原料易得,反应条件温和,产品收率及纯度都较高。     

Discourse cues to deception in the case of multiple receivers

Behavioral cues to deception are instrumental in detecting deception. As one of the primary sources of deception behavior, text has been analyzed at the level of sub-sentence or message but not the discourse of interaction. Additionally, empirical studies on cues to deception in the case of multiple receivers remain nonexistent. To fill these voids, we propose a discourse framework and six hypotheses about deception behaviors in a multi-receiver environment. The deception behaviors are operationalized by discourse features based on an analysis of real-world data. The results of statistical analysis validate the efficacy of discourse features in discriminating deceivers from truth-tellers.     

生物质中元素分布特征的聚类分析研究

测定了稻草秆、小麦秆、玉米秆、棉花秆、大豆秆、玉米芯、花生壳和柳树、松树、桦树、杨树、杉树 1 2个农业生物质和林业生物质种类 2 7个样品中主要元素 K,Ca,Na,Mg,Al,Fe,P和痕量元素 As,Cr,Co,Cu,Cd,Mn,Mo,Ni,Pb,Ti,Zn,V,Si,Ba,Be,Se,Sb,Ge,Hg的含量 ,并用SPSS聚类分析法分别进行了 R型和 Q型聚类研究 ,对这些元素在生物质中的分布特征进行了研究 .结果显示 :杨木、杉木和桦木与松木和柳木归成一大类 ,经济类作物黄豆秆和棉花秆分别归类后又归入一大类 ;农业生物质稻草秆和小麦秆、玉米秆被归入一类 ;虽然 2 7种生物质样品分别取自我国东北、华东、华北和西南地区 ,在地理位置上相距极远 ,但样品聚类谱系图表明 ,元素的分布特征与生物质的种类的关系显著 ,与产地的关系不明显 ,即元素的分布特征受种类的影响大 ,而受生长环境、气候、土壤条件的影响小 .     

羰基结构与亲核加成反应

羰基化合物是一类极为重要的有机化合物，本文从(1)醛酮(2)环酮(3)α，β-不饱和羰基化合物的结构讨论了羰基结构对其亲核加成活性的影响。     

Point-based online value iteration algorithm in large POMDP

Partially observable Markov decision process (POMDP) is an ideal framework for sequential decision-making under uncertainty in stochastic domains. However, it is notoriously computationally intractable to solving POMDP in real-time system. In order to address this problem, this paper proposes a point-based online value iteration (PBOVI) algorithm which involves performing value backup at specific reachable belief points, rather than over the entire belief simplex, to speed up computation processes, exploits branch-and-bound pruning approach to prune the AND/OR tree of belief states online, and proposes a novel idea to reuse the belief states that have been searched to avoid repeated computation. The experiment and simulation results show that the proposed algorithm can simultaneously satisfy the requirement of low errors and high timeliness in real-time system.