乙烯基三甲基硅烷等离子体聚合反应历程

应用色谱—质谱(GC-MS)及裂解色谱-质谱(PGC-MS)测定了乙烯基三甲基硅烷等离子体聚合反应中的气体冷凝物及聚合物,研究推导了等离子体聚合反应历程。单体在气相中被电子撞击,然后扩散到基底,在基底发生链增长和链终止反应。     

On-line multiversion database concurrency control

This paper presents a new model for studying the concurrency vs. computation time tradeoffs involved in on-line multiversion database concurrency control. The basic problem that is studied in our model is the following: Given:a current database system state which includes information such as which transaction previously read a version from which other transaction; which transaction has written which versions into the database; and the ordering of versions previously written; anda set of read and write requests of requesting transactions. Question: Does there exist a new database system state in which the requesting transactions can be immediately put into execution (their read and write requests satisfied, or in the case of predeclared writeset transactions, write requests are guaranteed to be satisfied) while preserving consistency under a given set of additional constraints? (The amount of concurrency achieved is defined by the set of additional constraints). In this paper we derive “limits” of performance achievable by polynomial time concurrency control algorithms. Each limit is characterized by a minimal set of constraints that allow the on-line scheduling problem to be solved in polynomial time. If any one constraint in that minimal set is omitted, although it could increase the amount of concurrency, it would also have the dramatic negative effect of making the scheduling problem NP-complete; whereas if we do not omit any constraint in the minimal set, then the scheduling problem can be solved in polynomial time. With each of these limits, one can construct an efficient scheduling algorithm that achieves an optimal level of concurrency in polynomial computation time according to the constraints defined in the minimal set.     

一种简便实用的视频特技切换器

本文介绍了一种用集成电路制作的特技切换器，具有成本低，线路简单，易于制作的特点。可以完成简单，基本的扫换，键控，特技效果和快切等功能。     

单片机的显示接口电路设计

介绍了利用单片机的串、并行接口和专用显示接口 IC 设计显示接口电路的方法,并提供了4种动态和静态显示的硬件接口电路。     

MPC系统模块结构中的流场研究

本研究中,应用Simple数值计算方法开发了求解MPC系统模块结构中二维流场分布的计算软件。为了验证计算结果的精确性,用多普勒测速仪实测了用有机玻璃制成的MPC模块二维模型的流场,模拟计算结果与实测值对比取得了较好的一致性。四种不同流出角的MPC模块平均总压损失计算结果表明,已开发的软件可作为设计低流阻MPC模块的良好工具。     

应用多孔阳极氧化电流—时间曲线比较壁垒膜厚

在有壁垒膜存在的表面,多孔膜的生长在氧化初期受到延迟阻碍,这一现象在直流恒压多孔阳极氧化电流一时间曲线上反映出来。电流达到稳态氧化的时间愈长,壁垒膜愈厚。文中应用此法判断了0.5MH_3BO_3介质的pH值、温度对壁垒阳极氧化膜厚的影响,并应用记录同一介质环境壁垒恒流阳极氧化的槽压一时间曲线得到验证。     

The investigation of 32P wire for catheter-based endovascular irradiation

The dose distribution from a 32P source has been measured and calculated in order to evaluate its application in endovascular irradiation. The source dimension was 27 mm in length and 0.3 mm in diameter and was embedded in the end of a Ni-Ti wire. Dose measurements were performed using radiochromic film in several specially designed tissue equivalent phantoms. Loevinger's point dose kernel was used for the calculation. The approximate dose rate at a radial distance of 1.5 mm from the center of the source was found to be 6.75 cGy/s per GBq (0.25 cGy/s per mCi), which allows the delivery of a therapeutic dose in a short time interval with a satisfactory homogeneity without stepping the source. However, the dose rate falls off almost exponentially along the radial distance. Therefore it may not be suitable for treating large diameter vessel from a centrally located source. The effect of a curved 32P wire source on the radial dose distribution was also investigated. The results showed that for a maximum bend of 180 degrees the dose rate was increased by as much as 20% along the inner radial distance but decreased by as much as 20% along the outer radial distance compared to the dose along a straight wire. However, for curvatures normally encountered in a clinical situation, the dose rate was changed less than 5%.     

硅中硼离子注入校准样品的研制

本文主要介绍了硅中硼离子注入校准样品的制备与研究。分别用三台SIMS仪器对样品进行了深度剖析与比对,并对用作校准目的的样品主要参数进行了定值。     

沸石催化剂在甲苯甲基化中的择形催化形用

综述了影响甲苯甲基化择形催化的因素,讨论了沸石的内外表面酸中心及酸强度、沸石的孔道、反应物和产物的吸附等因素对提高对二甲苯选择性的影响。