Piezoresistive Behavior Study on Finger‐Sensing Silicone Rubber/Graphite Nanosheet Nanocomposites

A novel finger‐sensing nanocomposite with remarkable and reversible piezoresistivity is successfully fabricated by dispersing homogeneously conductive graphite nanosheets (GNs) in a silicone rubber (SR) matrix. Because of the high aspect ratio of the graphite nanosheets, the nanocomposite displays a very low percolation threshold. The SR/GN nanocomposite with a volume fraction of conductive nanosheets closest to that for the percolation threshold presents a sharp positive‐pressure coefficient effect of the resistivity under very low pressure, namely, in the finger‐pressure range (0.3–0.7 MPa), whereby the abrupt transition could be attributed to compressive‐stress‐induced deformation of the conducting network. The super‐sensitive piezoresistive behavior of the nanocomposite is accounted for by an extension of the tunneling conduction theory which provides a good approximation to the piezoresistive effect.     

一种抗NLOS的TDOA定位算法

本文提出了一种抗非视线传播(Non-Line-of-Sight)干扰的TDOA定位算法。该算法采用退火与遗传算法相结合的方式，在满足给定条件的空间内搜索源点坐标值。数值仿真表明，该算法具备抗NLOS干扰的能力，与传统TDOA算法相比，该算法无需知道各基站的非视线传播干扰分布，是一种实用有效的定位算法。     

Enhancing echo cancellation via estimation of delay

The advent of packetized audio transmission, such as voice over IP (VoIP), has resulted in challenging requirements for echo cancellation technology. One key aspect of this technology is the need to characterize, quickly and accurately, the echo paths in the transmission media. Echo paths consist of a constant time delay with no echo signal and active regions in which the echo signal is present. When an adaptive filter echo cancellation algorithm is used, its performance can be greatly increased, and its complexity can be reduced if it is only applied to the active regions. This requires an algorithm to estimate the constant delay and locate the active regions. Traditionally, delay estimation has been based on direct application of cross-correlation. This method has poor performance because the input signals are highly correlated and has a high implementation cost because many cross-correlation lags have to be computed for longer time delays. The delay estimation addressed in this paper has two major advantages over the traditional methods. The first is that it has improved performance because the input signals are processed to have less correlation. The second is that the implementation cost is significantly reduced because fewer cross-correlation lags are computed, and an efficient method to estimate lags is created.     

Sphere packing with a geometric based compression algorithm

An efficient algorithm for the random packing of spheres can significantly save the cost of the preparation of an initial configuration often required in discrete element simulations. It is not trivial to generate such random packing at a large scale, particularly when spheres of various sizes and geometric domains of different shapes are present. Motivated by the idea of compression complemented by an efficient physical process to increase packing density, shaking, a new approach, termed compression algorithm, is proposed in this work to randomly fill any arbitrary polyhedral or cylindrical domains with spheres of various sizes. The algorithm features both simplicity and high efficiency. Tests show that it takes 181 s on a 1.4-GHz PC to complete the filling of a cylindrical domain with a total number of 26,787 spheres, achieving a packing density of 52.89%.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Peracetic acid pretreatment of sugarcane bagasse for enzymatic hydrolysis: a continued work

Previous work has shown that the enzymatic hydrolysis of sugarcane bagasse could be greatly enhanced by peracetic acid (PAA) pretreatment. There are several factors affecting the enzymatic digestibility of the biomass, including lignin and hemicelluloses content, cellulose crystallinity, acetyl group content, accessible surface area and so on. The objective of this work is to analyze the mechanism of the enhancement of enzymatic digestibility caused by PAA pretreatment. Delignification resulted in an increase of the surface area and reduction of the irreversible absorption of cellulase, which helped to increase the enzymatic digestibility. The Fourier transform infrared (FTIR) spectrum showed that the absorption peaks of aromatic skeletal vibrations were weakened or disappeared after PAA pretreatment. However, the infrared crystallization index (N.O'KI) was increased. X‐ray diffraction (XRD) analysis indicated that the crystallinity of PAA‐treated samples was increased owing to the partial removal of amorphous lignin and hemicelluloses and probable physical change of cellulose. The effect of acetyl group content on enzymatic digestibility is negligible compared with the degree of delignification and crystallinity. The results indicate that enhancement of enzymatic digestibility of sugarcane bagasse by PAA pretreatment is achieved mainly by delignification and an increase in the surface area and exposure of cellulose fibers. Copyright © 2008 Society of Chemical Industry     

电力负荷削峰减载系统在珠钢电炉的应用

借助现场采集装置,在计算机上获取每一分钟的冶炼工艺电能需求量,显示当前15分钟时段已发生的电耗量,调整用户设定,实现需量自动刷新、报警和专家分析推荐后续用量;实现平稳用电并减少对电网冲击,同时降低电能最大需用量以减少成本。     

Online and Offline Rotary Regression Analysis of Torque Estimator for Switched Reluctance Motor Drives

A new torque estimator for switched reluctance motor (SRM) drives based on 2-D rotary regression analysis is presented in this paper. The proposed torque estimator is composed of a bicubic regressive polynomial as a function of rotor position and input current. The regressive coefficients can be computed offline or online from the torque characteristics acquired either experimentally or from numerical computation. Furthermore, a torque estimation method by taking mutual coupling into consideration is proposed. It can be seen that the estimated and experimentally obtained self-coupling and mutual-coupling torque characteristics are in good agreement with each other. In addition, the dynamic torque waveforms with and without the mutual coupling, estimated by the proposed estimator, are found to be virtually the same as those obtained from the bicubic spline interpolation for SRM drives with single-pulse voltage, hysteresis current chopping, as well as with voltage pulse width modulation control. The success of all the case studies being reported is a good validation of the usefulness and accuracy of the proposed real-time torque estimator that, as described in this paper, can be used to quickly estimate the instantaneous output torque of SRM drives.