Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

Influence of protein and lipid concentration of the test lubricant on the wear of ultra high molecular weight polyethylene

To gain a better understanding of the ultra-high molecular weight polyethylene (UHMWPE) wear mechanism in the physiological environment, the effects of protein and lipid constituents of synovial fluid on the specific wear rate of UHMWPE were examined experimentally. The multidirectional sliding pin-on-plate wear tester was employed to simulate the simplified sliding condition of hip joint prostheses. Bovine serum γ-globulin and synthetic l--DPPC were used as model protein and lipid constituents of synovia, respectively. Results of the wear test indicated that the UHMWPE wear rate primarily depended on the protein concentration of the test lubricant. Lipids acted as a boundary lubricant and reduced polyethylene wear in the low protein lubricants. However, the polyethylene wear rate increased with increasing lipid concentrations if the protein concentration was within the physiological level. Increased interactions between protein and lipid molecules and lipid diffusion to polyethylene surface might be responsible for the increased wear.     

Design Techniques of CMOS Ultra-Wide-Band Amplifiers for Multistandard Communications

This paper presents design techniques of CMOS ultra-wide-band (UWB) amplifiers for multistandard communications. The goal of this paper is to propose a compact, simple, and robust topology for UWB low-noise amplifiers, which yet consumes a relatively low power. To achieve this goal, a common-gate amplifier topology with a local feedback is employed. The first amplifier uses a simple inductive peaking technique for bandwidth extension, while the second design utilizes a two-stage approach with an added gain control feature. Both amplifiers achieve a flat bandwidth of more than 6 GHz and a gain of higher than 10 dB with supply voltages of 1.8-2.5 V. Designs with different metal thicknesses are compared. The advantage of using thick-metal inductors in UWB applications depends on the chosen topology.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

Integrated carbon nanotube field emission differential amplifier: Modeling and measurement of the common-mode rejection ratio

A novel integrated vacuum field emission (VFE) differential amplifier (diff-amp) utilizing carbon nanotube (CNT) emitters has been developed. A dual-mask microfabrication process was employed to achieve a VFE diff-amp by integrating identical CNT VFE transistors with built-in split gates and integrated anodes. The identical pair of triode amplifiers was well-matched in their device characteristics. The measured ac small-signal characteristics of the diff-amp showed a common-mode-rejection ratio (CMRR) of ~ 320 (~ 50 dB). The proposed analytical model of the CMRR was verified to be in good agreement with the experimental data. The successful implementation of the CNT diff-amp demonstrates a new way to achieve temperature and radiation tolerant VFE integrated microelectronics.     

Ionothermal synthesis of a three-dimensional zinc phosphate with DFT topology using unstable deep-eutectic solvent as template-delivery agent

A three-dimensional zinc phosphate compound with DFT topology, designated as ZnPO₄-EU1, has been synthesized by an ionothermal approach from the system HF-ZnO–P₂O₅-choline chloride-imidazolidone. Ethylenediamine, derived from decomposition of the imidazolidone component of the deep-eutectic solvent (DES) itself, is delivered to the synthesis and serves as an appropriate template for ZnPO₄-EU1. Experiments in which the synthesis conditions were varied showed that ZnPO₄-EU1 may be prepared over a wide molar ratio of P/Zn = 0.55–13.0. Powder X-ray diffraction patterns have been obtained at intervals to track the crystallization process of this material. The experimental data show that Zn₃(PO₄)₂ · 4H₂O (a dense phase) was first isolated from the DES after reaction for 1 h. Subsequently, the pure phase of ZnPO₄-EU1 was obtained with increasing crystallization time from 12 h to 72 h. The experimental results show that the nucleation and crystallization take place with relatively low levels of solvent degradation, demonstrating that zinc phosphate with a three-dimensional framework can be synthesized by in situ generation of an appropriate template using an unstable DES at high temperatures (150–200 °C).     

Effect of vibration condition and inter-particle frictions on the packing of uniform spheres

We present a numerical study of the packing of uniform spheres under three-dimensional vibration using the discrete element method (DEM), focusing on the effects of vibration condition (amplitude and frequency) and inter-particle frictions (sliding and rolling frictions). The results are analysed in terms of packing density, coordination number (CN), radial distribution function (RDF) and pore structure. It is shown that increasing either the vibration amplitude or frequency causes packing density to increase initially to a maximum and then decrease. Both vibration frequency and amplitude should be considered to characterize the effect of vibration process on packing structure. The sliding and rolling frictions between particles can decrease packing density since they dissipate energy, although the effect of rolling friction is less significant. In line with the change of packing density, microstructural properties such as CN, RDF and pore distribution also change: a looser packing often corresponds to smaller CN, less peaked RDF and larger but more widely distributed pores.     

Formation mechanism of 21R AlN-polytypoids in aluminothermic reduction and nitridation process

Synthesis of 21R AlN polytypoids was investigated using Al and ultrafine SiO₂ powder in a flowing nitrogen atmosphere by means of thermal gravity (TG), differential scanning calorimeter (DSC), X-ray diffractometer (XRD) and scanning electronic microscope (SEM) linked with energy dispersive spectrometer (EDS). The results showed that the formation mechanism of AlN polytypoids was different from that in reaction sintering process using Si₃N₄, AlN, Al₂O₃ and other sintering additive as raw materials. It was suggested that firstly Al reduce SiO₂ into Si and is also nitrided into AlN, then AlN, Al₂O₃ and SiO₂ dissolve into silicon liquid until the AlN polytypoids precipitate in saturated liquid in a flowing nitrogen atmosphere at lower than 1700 °C.     

熟悉而又陌生

《Frame》总第46期向读者展示了许多有意思的想法和创意的细节下面是从中摘选出来的设计和空间方案他们都运用到了我们身边很熟悉的元素，在这里“腐朽”一下化神奇了。[编者按]