A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

Digitally tunable optical filters using arrayed-waveguide grating(AWG) multiplexers and optical switches

Two novel configurations for digitally tunable optical filters based on arrayed-waveguide grating (AWG) multiplexers are described in detail with emphasis on the connection of the AWG multiplexer and optical switches. Performance comparisons show that conventional configurations are disadvantaged by the switch size required and loss imbalance among the optical frequency-division-multiplexed (FDM) channels; the proposed configurations require only O(√(N)) switch elements to select one of N FDM channels, and the loss imbalance is lower by up to 75% in decibel     

Transmission capacity of optical path overhead transfer schemeusing pilot tone for optical path network

Photonic networks based on the optical path concept and wavelength division multiplexing (WDM) technology require unique operation, administration, and maintenance (OAM) functions. In order to realize the required OAM functions, the optical path network must support an effective management information transfer method. The method that superimposes a pilot tone on the optical signal appears very interesting for optical path overhead transfer. The pilot tone transmission capacity is determined by the carrier to noise ratio which depends on the power spectral density of the optical signal. The pilot tone transmission capacity of an optical path network employing WDM technology is elucidated; 4.5 kb/s transmission can be realized when the pilot tone modulation index is set at 3%     

An improved Gaussian approximation for probability of bit-erroranalysis of asynchronous bandlimited DS-CDMA systems with BPSK spreading

This paper analyzes probability of bit-error (P_e) performance of asynchronous bandlimited direct-sequence code-division multiple-access systems with binary phase-shift keying spreading. The two present methods of P_e analysis under bandwidth-efficient pulse shaping: the often-cited standard Gaussian approximation and the characteristic function (CF) method suffer from either a low accuracy in regions of low P_e (< 10^-3) or a prohibitively large computational complexity. The paper presents an alternate method of P_e analysis with moderate computational complexity and high accuracy based on a key observation. A sequence of chip decision statistics (whose sum yields a bit statistic) forms a stationary, m-dependent sequence when conditioned on the chip delay and phase offset of each interfering signal. This observation permits the generalization of the improved Gaussian approximation previously derived for the rectangular pulse and the derivation of a numerically efficient approximation based on the CF method. Numerical examples of systems using the square-root raised-cosine and IS-95 pulses illustrate THE P _e performance, user capacity and the accuracy of the proposed method     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

New insights in polarity-dependent oxide breakdown for ultrathin gate oxide

In this work, a quantitative analysis is applied to resolve the newly reported polarity-dependent charge-to-breakdown (Q/sub BD/) data from thick oxides of 6.8 nm down to ultrathin oxides of 1.9 nm. Three independent sets of Q/sub BD/ data, i.e., n/sup +/poly/NFET stressed under inversion and accumulation, and p/sup +/ poly/PFET under accumulation are carefully investigated. The Q/sub BD/ degradation observed for p-type anodes, either poly-Si or Si-substrate, can be nicely understood with the framework of maximum energy released by injected electrons. Thus, this work provides a universal and quantitative account for a variety of experimental observations in the time-to-breakdown (T/sub BD/) and Q/sub BD/ polarity-dependence of oxide breakdown.     

Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.