Cellulose templating method for the preparation of La0.8Sr0.2Ga0.83Mg0.17O2.815 (LSGM) solid oxide electrolyte

La_0.8Sr_0.2Ga_0.83Mg_0.17O_2.815 (LSGM) materials are synthesized with a fast and facile cellulose templating method for the first time and characterized by XRD, EIS, Archimedes method and SEM–EDS. LSGM powders with a phase purity of 91.7 mol% are obtained after the calcination at 1300 °C for 12 h. SEM–EDS results indicate possible decomposition and reconstruction of the LSGM phase due to the diffusion of Sr-rich species to the grain boundaries for the sample sintered at 1500 °C for 6 h. Maximum conductivity value is found to be 4.2 × 10^?2 S cm^?1 at 800 °C for the sample calcined at 1300 °C for 12 h and sintered at 1400 °C for 6 h. Phase purity, stability and relative density are the important factors for obtaining high performance LSGM electrolytes. Therefore, cellulose templating method is a promising candidate for the preparation of LSGM electrolytes.     

Off-line optimization and control for real time integration of a three-phase hydrogenation catalytic reactor

In order to develop and test the integration procedure, in this paper a real time process integration involving the optimization and control of the process is presented, in this case, with the two-layer approach. The used optimization algorithms were Levenberg–Marquardt and SQP that solve a non-linear least square problem subject to bounds on the variables. The two-layer approach is a hierarchical control structure where an optimization layer calculates the set points and manipulated variables to the advanced controller, which is based on the dynamic matrix control with constraints (QDMC). The non-isothermal dynamic model of the three-phase slurry catalytic reactor with appropriate solution procedure was utilized in this work (Vasco de Toledo, E. C., Santana, P. L., Maciel, M. R. W., & Maciel Filho, R. (2001). Dynamic modeling of a three-phase catalytic slurry reactor. Chemical Engineering Science, 56, 6055–6061). The model consists on mass and heat balance equations for the catalyst particles as well as for the bulk phases of gas and liquid. The model was used to describe the dynamic behavior of hydrogenation reaction of o-cresol to obtain 2-methil-cyclohexanol, in the presence of a catalyst Ni/SiO₂.     

Effects of Various Preparation and Polymerization Procedures on the Isospecific Nature of TiCl3-Based Polypropylene Catalysts

Summary As one of a series approaches in using two-component and three-component donor-free Ziegler–Natta catalysts, in this preliminary work, the effects of various preparation and polymerization conditions including catalyst preparation by wet- or dry- grinding, the type of cocatalyst, with or without pretreatment of catalyst by cocatalyst before polymerization, Al/Ti molar ratio and polymerization temperature, etc., on the isospecific nature of active sites of the TiCl₃ catalyst were studied through a systematic characterization of the PPs by a combination of GPC, ¹³C-NMR with TREF method. It was demonstrated that the types of Al-alkyl cocatalysts play the most dominant role in determination of isospecificity of activate sites and its distribution. A plausible mechanism (Scheme 1) regarding the formation of isospecific active sites with different stability in terms of Ti–Al bimetallic complexing depending on the type of cocatalyst had been proposed. Except the catalyst grinding method, other factors eg., pretreatment, temperature, and Al/Ti molar ratio, etc. did not show obvious effects on the isospecific nature of active sites.     

Mechanical Properties and Microstructure of a Metakaolin-Based Inorganic Polymer Mortar Reinforced with Quartz Sand

Silicon - The synthesis, mechanical behaviour, and microstructure of metakaolin-based geopolymer mortar reinforced with quartz sand are presented in this investigation. Fine sand (quartz sand)...     

Silicon Application Enhances the Photosynthetic Pigments and Phenolic/Flavonoid Content by Modulating the Phenylpropanoid Pathway in Common Buckwheat under Aluminium Stress

Silicon - Silicon (Si) is very effective in the amelioration of heavy metal (HM) stress in different crop plants. This investigation was conducted to assess the protective role of Si in modulating...     

BaTiO3–Bi(Mg2/3Nb1/3)O3 Ceramics for High‐Temperature Capacitor Applications

Solid solutions of (1?x)BaTiO₃–xBi(Mg_2/3Nb_1/3)O₃ (0 ≤ x ≤ 0.6) were prepared via a standard mixed‐oxide solid‐state sintering route and investigated for potential use in high‐temperature capacitor applications. Samples with 0.4 ≤ x ≤ 0.6 showed a temperature independent plateau in permittivity (ε_r). Optimum properties were obtained for x = 0.5 which exhibited a broad and stable relative ε_r ~940 ± 15% from ~25°C to 550°C with a loss tangent <0.025 from 74°C to 455°C. The resistivity of samples increased with increasing Bi(Mg_2/3Nb_1/3)O₃ concentration. The activation energies of the bulk were observed to increase from 1.18 to 2.25 eV with an increase in x from 0 to 0.6. These ceramics exhibited excellent temperature stable dielectric properties and are promising candidates for high‐temperature multilayer ceramic capacitors for automotive applications.     

Maleated high oleic sunflower oil‐treated cellulose fiber‐based styrene butadiene rubber composites

Surface treatment of cellulose fibers was performed with maleated high oleic sunflower oil (MSOHO). The MSOHO‐treated cellulose fibers and unmodified cellulose fibers were dispersed in styrene butadiene rubber (SBR) using a two roll mill. Vapor grown carbon nanofibers (VGCNF) were also incorporated at only one parts per hundred rubber (phr) in unmodified cellulose fibers/SBR composites. The curing characteristics, mechanical properties, and water absorption of the resulting composites were determined. MSOHO‐treated fibers completed curing at much slower rate and also decreased the cure density of composites, compared to unmodified fibers. In contrast, the combination of VGCNF and unmodified cellulose fibers accelerated the SBR curing process, but reduced the cure density. MSOHO treatment improved the dispersion of the fibers in the SBR, which resulted in improved mechanical properties of composites. The composite incorporating 1 phr VGCNF and 15 phr unmodified cellulose fibers showed the greatest increase in tensile strength as compared with neat SBR. POLYM. COMPOS. 37:1113–1121, 2016. © 2014 Society of Plastics Engineers     

A green separation process for recovery of healthy oil from pumpkin seed

In this study, pumpkin seeds, called as “Ürgüp Sivrisi” and grown in Cappadocia region, were used as plant materials because of high aroma contents. In the supercritical fluid extraction of pumpkin seed oil, the effect of main process parameters as the particle size (250-2360 μm), the volumetric flow rate of supercritical solvent (0.06-0.30 L/h), the operating pressure (20-50 MPa), the operating temperature (40-70 °C), the type of entrainer (ethanol and n-hexane) and those concentrations (0-10 vol.%) on the extraction yield, the oil solubility and the initial extraction rate were investigated. A cross-over effect for the extraction of pumpkin seed oil using supercritical CO₂ was determined at the operating pressure of 20-30 MPa. The maximum extraction yield obtained with entrainer free was reached 0.50 g oil/g dry seed at 600-1180 μm, 0.12 L/h, 50 MPa and 70 °C for the operation time of 5 h. The maximum extraction yield obtained with ethanol as an entrainer in the experiments was reached 0.54 g oil/g dry seed at the conditions of 600-1180 μm, 0.12 L/h, 30 MPa, 40 °C and 8 vol.% for the operating time of 2 h. The oil compositions were determined by gas chromatography analysis and the results showed that the compositions of pumpkin seed oil which were obtained by means of organic solvent extraction and supercritical fluid extraction were similar. The average oil compositions determined as 9.3 (±0.43)% palmitic acid, 7.5 (±0.6)% stearic acid, 32.3 (±0.6)% oleic acid, 48.1 (±0.6)% linoleic acid and 0.7 (±0.3)% linolenic acid. The morphological changes in the seeds were determined by the scanning electron microscopy analysis.     

Effects of nanoclay and coupling agent on the physico‐mechanical,morphological, and thermal properties of wood flour/polypropylene composites

This article presents the effects of coupling agent and nanoclay (NC) on some properties of wood flour/polypropylene composites. The composites with different NC and maleic anhydride grafted polypropylene (MAPP) contents were fabricated by melt compounding in a twin‐screw extruder and then by injection molding. The mass ratio of the wood flour to polymer was 40/60 (w/w). Results showed that applying MAPP on the surface of the wood flour can promote filler polymer interaction, which, in turn, would improve mechanical properties of the composite as well as its water uptake and thermal stability. Composite voids and the lumens of the fibers were filled with NC, which prevented the penetration of water by the capillary action into the deeper parts of composite. Therefore, the water absorption in composites fabricated using NC was significantly reduced. Scanning electron microscopy has shown that the treatment of composites with 5 wt% MAPP, promotes better fiber–matrix interaction, resulting in a few numbers of pull‐out traces. In all cases, the degradation temperatures shifted to higher values after using MAPP. The largest improvement on the thermal stability of composites was achieved when NC was added. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

十六烷基三甲基季铵阳离子改良二氧化硅对酸性染料的吸着

The sorption behavior of acid dyes onto cetyltrimethylammonium bromide (CTAB)-modified silica as a function of pH in the aqueous medium was studied. Single-and multi-solute sorption equilibria of orange Ⅱ（OR), phenol red (PR) and Eriochrome Black T (EBT) were studied at pH 3, unbuffered water pH and pH 11. Sorption behavior of EBT could not be conducted at pH3 due to its aggregation in acidic medium. All the reaction conditions, experimental protocols and techniques remained the same throughout the sorption process. Sorption isotherms for single-solute system were fitted by the Langmuir model, while Langmuir competitive model (LCM) and the ideal adsorbed solution theory (IAST) coupled with Langmuir model (IAST/Langmuir) were used for the prediction of multisolute competitive sorption. Sorption affinities influenced by the factors like physical interactive forces between the molecules of CTA on silica and sorbate, structural limitations of the dyes based on their geometrical arrangement were investigated. Sorption affinity of OR was found to be higher than that of EBT and PR at all the pH values investigated. Magnitude of the sorption capacities was observed to be higher in acidic medium but lower in alkaline medium. Trends of the sorption affinities in multisolute system were simlar to those in single-solute system but magnitude of the sorption capacities was significantly reduced due to the prevailing competition among the sorbates.