Partial discharge measurements in SF6 and air usingphase-resolved pulse-height analysis

Carries out a study on partial discharge (PD) phenomena in SF₆ gas and tries to construct a diagnostic system capable of separating noise from observed PD signals for assessing the condition of insulation performance in power apparatus. The authors have constructed a computer-aided PD measuring system which permits a time-sequential data acquisition and phase-resolved pulse height analysis. Using the PD measurement system, the authors measured 60 Hz AC PD in SF₆ gas and in air at atmospheric pressure for needle-plane electrodes with three different radii at the tip of the needle, 3, 30 and 500 μm. They proposed particular PD statistical parameters, unbalance ratios U _T and U_q of the pulse repetition rate and average of charge, respectively, between positive and negative PD pulses occurring per cycle; these parameters proved to be good indicators to distinguish PD occurring in SF₆ from that in air. The mechanism of PD inception was also discussed     

Area and volume effects on breakdown strength in liquid nitrogen

We measured dc and ac breakdown voltages in liquid nitrogen (LN ₂) with a sphere-to-plane electrode configuration. Experimental results revealed that the breakdown voltage in LN₂ did not increase monotonously but partially decreased as the sphere diameter increased at a constant gap length. Thus, the existence of the area and the volume effects on the breakdown voltage in LN₂ was verified quantitatively; the breakdown strength decreased when increasing the {SEA}₉₀ (90% stressed electrode area) and the {SLV}₉₀ (90% stressed liquid volume). By changing the experimental conditions, it was verified that both area and volume effects, having a mutual correlation, simultaneously lead to the degradation of the breakdown strength in LN₂. In order to examine the area and the volume effects for the larger {SEA}₉₀ and {SLV}₉₀, we also measured the breakdown voltage with a coaxial cylindrical electrode. It was concluded that the dc and ac breakdown strengths in LN₂ decreased as the {SEA}₉₀ and the {SLV}₉₀ increased varying widely from 10⁰ to 10⁵ mm² and from 10 ^-1 to 10⁵ mm³, respectively     

Solubility and diffusivity of oxygen in aqueous sucrose solutions

Solubility and diffusivity of oxygen in aqueous sucrose solutions of various concentrations were measured at temperatures from 15° to 45°C and at atmospheric pressure. The solubility of oxygen could be correlated well by the method of van Krevelen and Hoftijzer. The diffusivity of oxygen was found to be proportional to the ?2/3 power of the viscosity of the solution.     

Velocity, electromechanical coupling factor and acoustic loss of surface shear waves propagating along x-axis on rotated Y-cut plates of LiNbO3

Velocity and propagation loss of surface shear waves are measured on free-space and metallised surfaces of LiNbO3 crystals along the x-axis of rotated Y-cut plates as a function of rotation about the x-axis between 35° and 70°. The coupling factor obtained from the velocities is 0.20 for a 35° rotated Y-cut plate and 0.09 for a 70° plate. The coupling factor changes linearly with the rotation angle. The propagation losses over the whole range measured here are less than 5 dB/cm on both free-space and on metallised surfaces. These losses are fairly low and very favourable for fabricating s.a.w. filters.     

Solid-state microwave relay systems in Japan

In response to the rapidly increasing demand for communication facilities, microwave relay systems have played an important role in Japan's telecommunications network because of their economy and capability for broadband transmission. Their progress has been marked during the past 20 years and this development has been supported by advances in such diverse fields as radio propagation, antennas, microwave and electronic circuitry, electron devices, and, particularly, in solid-state techniques. This article reviews the history of microwave relay systems and describes the past and expected future contributions of the solid-state technology to these systems.     

Dynamic breakdown characteristics of liquid helium induced by aquench of superconducting wire and coil

For practical insulation design of superconducting power apparatus, it is necessary to take into account an inherent phenomenon known as quench, the transition from the superconducting to the normal state. We investigated quench-induced dynamic breakdown and prebreakdown characteristics of liquid helium (LHe). Experimental results revealed that the quench of the superconductor drastically reduced the breakdown voltage of LHe in the thermal bubble disturbance. Moreover, dynamic breakdown characteristics in a quasi-uniform field using a superconducting coil were investigated. The results revealed that the breakdown was induced in the quench-initiated region where the largest thermal energy was generated     

Sonochemical Preparation and Properties of Pt–3Y-TZP Nano-Composites

A uniformly aggregated 3 mol% yttria-stabilized tetragonal zirconia nano-powder (3Y-TZP) was prepared using thermal hydrolysis and the ultrasonic deagglomeration technique. The possibility of nano-engineering of Pt–3Y-TZP composite aggregates was studied. The as-synthesized Pt nano-particles (∼2 nm) were impregnated into zirconia nano-aggregates (20–45 nm). The morphology manipulation technique allowed production of the composite zirconia-based aggregates in which a significant fraction of the Pt particles was embedded into the densified zirconia aggregates. Using the colloidal technique and low-temperature (1150°C) sintering, we prepared the Pt-zirconia (0.5–1.5 wt% of platinum) nano-composites with average 3Y-TZP grain sizes of 120 nm, and with the platinum grains size in the range of 20–60 nm. The catalytic properties of composite Pt–3Y-TZP nano-composites were studied and described.