Influence of the degree of crosslinking on the stringiness of crosslinked polyacrylic pressure‐sensitive adhesives

The stringiness of crosslinked polyacrylic pressure‐sensitive adhesive (PSA) was observed during 90° peeling under the constant peel load. The random copolymer of butyl acrylate with 5 wt % acrylic acid crosslinked by N,N,N′,N′‐tetraglycidyl‐m‐xylenediamine was used as PSA. All observed stringiness upon peeling was sawtooth‐shaped, but it could be classified into three types dependent on the degree of crosslinking. The typical sawtooth‐shaped stringiness with interfacial failure was observed at the relatively higher crosslinker content ranging from 0.008 to 0.016 chemical equivalents (Eq.), where the PSA has high cohesive strength and low interfacial adhesion. The frame formed at the front end of stringiness at the content ranging from 0.002 to 0.004 Eq. Sufficient interfacial adhesion and deformability generate large internal deformation of the PSA layer. Internal deformation occurred preferentially over peeling as a result of front frame formation. The mode of peeling was changed from cohesive failure to interfacial failure in this range of crosslinker content. The sawtooth‐shaped with cohesive failure was observed at the lower content ranging from 0 to 0.001 Eq. The PSA has high interfacial adhesion and low cohesive strength, and thus exhibited cohesive failure. The PSA after peeling remained in the shape of belts. It was found that the shape of stringiness is strongly dependent on the balance between the interfacial adhesion and the cohesive strength of PSA. When the sawtooth‐shaped stringiness with frame formed, the peeling rate was lowest. This means the peel strength should be the maximum in this shape of stringiness. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40336.     

From topological gels to slide‐ring materials

A novel type of gel, called a topological gel, has been recently developed with a supramolecular architecture with topological characteristics. In the topological gel, polymer chains with bulky end groups are neither covalently crosslinked as in chemical gels nor attractively interacting as in physical gels but are topologically interlocked by figure‐eight shaped crosslinks. Hence, these crosslinks can pass along the polymer chains freely to equalize the tension of the threading polymer chains similarly to pulleys; this is called the pulley effect. This concept can be applied not only to gels but also to a wide variety of polymeric materials without solvents. Then, polymeric materials with movable crosslinks are referred to as slide‐ring materials (SRMs) in a wider sense. Here, we review the synthesis, structure, physical properties, and applications of topological gels and SRMs. In particular, slide‐ring elastomers show remarkable scratch‐proof properties for application to coating materials for automobiles, cell phones, mobile computers, golf clubs, and so on. © 2014 The Authors Journal of Applied Polymer Science Published by Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40509.     

Formal Nucleophilic Boryl Substitution of Organic Halides with Silylborane/Alkoxy Base System

Boryl substitution of organohalides with a silylborane and alkoxy bases is described. This reaction can be applied to various functionalized aryl halides. Alkyl and alkenyl halides, and even sterically congested aryl bromides also provided the corresponding borylated products in high yields. Mechanistic studies indicated that neither trace transition-metal impurities nor aryl radical species involved in this reaction.     

Nanomodification of Glass Using fs Laser

We review the interaction of glass with intense ultrashort laser pulses revealing new phenomena and recent demonstrations of rewritable 5D optical memory and polarization imaging filter mediated by the self-organization of nanostructure. Particularly, we experimentally verify linearly polarized intense ultrashort pulses can control the direction of local optical anisotropy in homogeneous medium based on the interference between photon and electron plasma. These so-called “nanogratings” composed of the photoinduced oxygen defects emerge in the course of multiple laser pulses and are oriented perpendicularly to the laser polarization direction. The nanograting structures, which exhibit form birefringence, have evolved from residual birefringence along with lowering threshold for defect formation into self-assembly of oxygen defects.     

巴塞罗那费拉Porta Fira双子塔

<正>作为巴塞罗那L' Hospitalet市都市再开发项目的一部分,费拉Porta Fira双子塔伫立于欧洲广场内。该基地位于巴塞罗那市和ElPrat国际机场之间,距离巴塞罗那ElPrat国际机场仅为8km,并构成了Barcelona Gran Via Fair会场的延伸部分,营造出一个引导人们进入活动区域的门户。     

Viscoelastic flow analysis of surface morphology on injection‐molded polypropylene

The molecular orientation of a frozen layer in an injection‐molded specimen of a polypropylene–rubber blend was investigated. A typical V‐shaped pattern of birefringence was observed from the surface to the core in a crosscut section. From the comparison of the V‐patterns near the gate to the flow end, it was assumed that a frozen layer formed from the surface to a depth of 0.06 mm in a plaque (3 mm thickness) during the injection molding filling process. Numerical viscoelastic analysis of the fountain flow was carried out using an original 2D unsteady flow simulation program and ignored crystallization. A large extensional deformation formed just when the molten polymer contacted the cavity wall and the deformation immediately froze. A layer with a small birefringence between the surface and the shear‐oriented layer was divided into two parts. The depth profile of birefringence was compared to the principal stress difference calculated by numerical analysis. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Computational Prediction of O-linked Glycosylation Sites That Preferentially Map on Intrinsically Disordered Regions of Extracellular Proteins

O-glycosylation of mammalian proteins is one of the important posttranslational modifications. We applied a support vector machine (SVM) to predict whether Ser or Thr is glycosylated, in order to elucidate the O-glycosylation mechanism. O-glycosylated sites were often found clustered along the sequence, whereas other sites were located sporadically. Therefore, we developed two types of SVMs for predicting clustered and isolated sites separately. We found that the amino acid composition was effective for predicting the clustered type, whereas the site-specific algorithm was effective for the isolated type. The highest prediction accuracy for the clustered type was 74%, while that for the isolated type was 79%. The existence frequency of amino acids around the O-glycosylation sites was different in the two types: namely, Pro, Val and Ala had high existence probabilities at each specific position relative to a glycosylation site, especially for the isolated type. Independent component analyses for the amino acid sequences around O-glycosylation sites showed the position-specific existences of the identified amino acids as independent components. The O-glycosylation sites were preferentially located within intrinsically disordered regions of extracellular proteins: particularly, more than 90% of the clustered O-GalNAc glycosylation sites were observed in intrinsically disordered regions. This feature could be the key for understanding the non-conservation property of O-glycosylation, and its role in functional diversity and structural stability.     

Practical cell labeling with magnetite cationic liposomes for cell manipulation

Personalization of the cell culture process for cell therapy is an ideal strategy to obtain maximum treatment effects. In a previous report, we proposed a strategy using a magnetic manipulation device that combined a palm-top size device and a cell-labeling method using magnetite cationic liposomes (MCLs) to enable feasible personalized cell processing. In the present study, we focused on optimizing the MCL-labeling technique with respect to cell manipulation in small devices. From detailed analysis with different cell types, 4 pg/cell of MCL-label was found to be obtained immediately after mixing with MCLs, which was sufficient for magnetic cell manipulation. The amount of label increased within 24 h depending on cell type, although in all cases it decreased along with cell doubling, indicating that the labeling potential of MCLs was limited. The role of free MCLs not involved in labeling was also investigated; MCLs' role was found to be a supportive one that maximized the manipulation performance up to 100%. We also determined optimum conditions to manipulate adherent cells by MCL labeling using the MCL dispersed in trypsin solution. Considering labeling feasibility and practical performance with 10³–10⁵ cells for personalized cell processing, we determined that 10 μg/ml of label without incubation time (0 h incubation) was the universal MCL-labeling condition. We propose the optimum specifications for a device to be combined with this method.     

Zeolite synthesis from paper sludge ash at low temperature (90 degrees C) with addition of diatomite

Paper sludge ash was partially converted into zeolites by reaction with 3M NaOH solution at 90 degrees C for 24 h. The paper sludge ash had a low abundance of Si and significant Ca content, due to the presence of calcite that was used as a paper filler. Diatomite was added to the NaOH solution to increase its Si content in order to synthesize zeolites with high cation exchange capacity. Diatomite residue was filtered from solution before addition of ash. The original ash without addition of diatomite yielded hydroxysodalite with a cation exchange capacity ca. 50 cmol/kg. Addition of Si to the solution yielded Na-P1 (zeolite-P) with a higher cation exchange capacity (ca. 130 cmol/kg). The observed concentrations of Si and Al in the solution during the reaction explain the crystallization of these two phases. The reaction products were tested for their capacity for PO(4)(3-) removal from solution as a function of Ca(2+) content, suggesting the formation of an insoluble Ca-phosphate salt. The product with Na-P1 exhibits the ability to remove NH(4)(+) as well as PO(4)(3-) from solution in concentrations sufficient for application in water purification. Both NH(4)(+) and PO(4)(3-) removal showed little variation with pH between 5 and 9. Alternative processing methods of zeolite synthesis, including the addition of ash to an unfiltered Si-NaOH solution and addition of a dry ash/diatomite mixture to NaOH solution, were tested. The third process yielded materials with lower cation exchange capacity due to formation of hydroxysodalite. The second process results in a product with relatively high cation exchange capacity, and reduces the number of processing steps necessary for zeolite synthesis.     

Alignment of glycolipid nanotubes on a planar glass substrate using a two-step microextrusion technique

We have developed a two-step microextrusion technique to align lipid nanotubes of 200 nm in diameter in parallel on planar glass substrates. This technique is useful to align self-assembled molecular nanofibers or nanotubes with diameters ranging from 100 to 300 nm. In the first step, we applied relatively large air pressure (approximately 40 hPa) onto a microcapillary filled with aqueous dispersion of lipid nanotubes to push them out. An aqueous droplet with 60 microm diameter was then extruded from the tip of the microcapillary. After one end of the lipid nanotube moved out, we changed the air pressure to be smaller, approximately 20 hPa to reduce the flow rate of the dispersion. The decrease in size of the droplet allowed us to fix the exposed end of the lipid nanotube onto the planar substrate. By dragging the microcapillary along the planar surface, we were able to align the whole nanotube onto the substrate. Using this technique, we have achieved the parallel alignment of the lipid nanotubes on the glass substrate.