Scalable Model of On-Wafer Interconnects for High-Speed CMOS ICs

This paper describes the development of an equivalent circuit model of on-wafer interconnects for high-speed CMOS integrated circuits. By strategically cascading two-pi blocks together, the lumped model can characterize the distributed effects. Besides, the elaborately proposed model characterizes the frequency-variant characteristics with frequency-independent components. Thus, the model can be easily plugged into commercial computer-aided design tools. By adopting a newly invented optimization algorithm, namely, particle swarm optimization (PSO), the model parameters are extracted and formulated as empirical expressions. Therein, with each set of the geometrical parameters, the interconnect behaviors can be accurately predicted. The accuracy of the model is validated by comparisons with the on-wafer measurements up to 30 GHz. Moreover, the scalability of the proposed model is also discussed     

Reversible Conversion Reactions and Small First Cycle Irreversible Capacity Loss in Metal Sulfide‐Based Electrodes Enabled by Solid Electrolytes

Solid‐state batteries can potentially enable new classes of electrode materials which are unstable against liquid electrolytes. Here, SnS nanocrystals, synthesized by a wet chemical method, are used to fabricate a Li‐ion electrode, and the electrochemical properties of this electrode are examined in both solid and liquid electrolyte designs. The SnS‐based solid‐state cell delivers a capacity of 629 mAh g^?1 after 100 cycles and exhibits an unprecedentedly small irreversible capacity in the first cycle (8.2%), while the SnS‐based liquid cell shows a rapid capacity decay and large first cycle irreversible capacity (44.6%). Cyclic voltammetry (CV) experiments show significant solid electrolyte interphase (SEI) formation in the liquid cell during the first discharge while SEI formation by electrolyte reduction in the solid‐state cell appears negligible. Along with CV, X‐ray photoelectron spectroscopy and energy dispersive spectroscopy are used to investigate the differences between the solid‐state and liquid cells. The reaction chemistry of SnS in solid‐state cells is also studied in detail by ex situ X‐ray diffraction and X‐ray absorption spectroscopy. The overarching findings are that use of a solid electrolyte suppresses materials degradation and electrolyte reduction which leads to a small first cycle irreversible capacity and stable cycling.     

A general expression of dyadic Green's functions in radiallymultilayered chiral media

A general expression of spectral-domain dyadic Green's function (DGF) is presented for defining the electromagnetic radiation fields in spherically arbitrary multilayered and chiral media. Without any loss of the generality, each of the radial multilayers could be the chiral layer with different permittivity, permeability, and chirality admittance, while both distribution and location of current sources are assumed to be arbitrary. The DGF is composed of the unbounded DGF and the scattering DGF, based on the method of scattering superposition. The scattering DGF in each layer is constructed in terms of the modified and normalized spherical vector wave functions. The coefficients of the scattering DGFs are derived and expressed in terms of the equivalent reflection and transmission coefficients, by applying boundary conditions satisfied by the coefficient matrices     

Designing a Stable Cathode with Multiple Layers to Improve the Operational Lifetime of Polymer Light‐Emitting Diodes

The short device lifetime of blue polymer light‐emitting diodes (PLEDs) is still a bottleneck for commercialization of self‐emissive full‐color displays. Since the cathode in the device has a dominant influence on the device lifetime, a systematic design of the cathode structure is necessary. The operational lifetime of blue PLEDs can be greatly improved by introducing a three‐layer (BaF₂/Ca/Al) cathode compared with conventional two‐layer cathodes (BaF₂/Al and Ba/Al). Therefore, the roles of the BaF₂ and Ca layers in terms of electron injection, luminous efficiency, and device lifetime are here investigated. For efficient electron injection, the BaF₂ layer should be deposited to the thickness of at least one monolayer (～3 nm). However, it is found that the device lifetime does not show a strong relation with the electron injection or luminous efficiency. In order to prolong the device lifetime, sufficient reaction between BaF₂ and the overlying Ca layer should take place during the deposition where the thickness of each layer is around that of a monolayer.     

NCl(α)/I全气相碘激光与氧碘化学激光能量提取的分析比较

利用连续流光腔动力学模型,对氧碘化学激光(COIL)和基于NCl(α)-I传能的全气相碘激光(AGIL)的能量提取进行了分析和公式推导,得到了连续流光腔的光子通量解析表达式以及氧碘化学激光光子通量沿流动方向的分布和输出功率的简化计算公式.AGIL的体系较为复杂,不能得到光子通量沿流动方向分布和输出功率的简化计算公式.从能量提取和体积重量效率角度,对氧碘化学激光和基于NCl(α)-I传能的全气相碘激光进行了对比评价.     

Trisneopentylgallium as a precursor for atomic layer epitaxy of GaAs

We report the use of a new precursor, trisneopentylgallium (NPG) for the growth of GaAs by atomic layer epitaxy (ALE). In contrast to most other alkyl gallium precursors such as triethylgallium, which decompose via a β-hydride elimination mechanism, this compound undergoes homolysis similar to that of trimethylgallium (TMGa), the normal choice as an ALE precursor. Clear self-limiting growth behavior similar to that of TMGa was observed over a reasonably wide range of growth conditions (430–500°C). Carbon incorporation was not significantly reduced compared with TMGa suggesting that the adsorbed neopentyl radicals undergo decomposition to result in a methyl terminated surface identical to that obtained for growth with TMGa.     

Performance of DS SS system under on-off wideband jamming

A performance analysis of a direct sequence spread spectrum (DS SS) system under a periodic on-off wideband jammer is presented. Closed-form results of system bit error rate (BER) are derived for all possible cases of jammer duty cycle     

The near-zone field characteristics of an E-polarization plane wavepenetrating through cylindrical multiple apertures (non) coated withlossy and lossless media

The direct integral equation is formulated for describing the current on the multiple perfectly conducting strips in cylindrical geometries for an E-polarization plane wave of normal incidence. By using the Galerkin's method, the surface currents on the conducting strips are expanded in the form of a series of Chebyshev polynomials of the first kind, while the unknown expanding coefficients are solved by a set of matrix equations of finite order with a fast convergence rate and a high accuracy. Furthermore, numerical results are presented to demonstrate the variation of the penetrated near-zone field in the presence of one, two, three, four and six cylindrical apertures, and the hybrid effects of both aperture number and aperture angular widths on the penetrated fields are investigated in detail     

Performance of Efficient Signal Detection for LED-ID Systems

In this paper, effects of reader-to-reader interference are investigated for LED identification (LED-ID) system in a multi-reader environment. The LED-ID readers typically use different channels to avoid collision between readers. However, in-channel collision usually happens in terms of interrogation range. A reader-to-reader interference scenario is proposed, and nominal interrogation range of a desired reader is derived from this model. In order to evaluate the LED-ID reader-to-reader interference quantitatively, an efficient detection scheme is proposed and simulated by employing spreading sequence. The spreading sequence is inserted between each user’s frame formats. In the receiver, the desired signal is detected by using correlation among inserted spreading sequences. From simulation results, it is confirmed that the proposed scheme is very effective to enhance reliability of LED-ID communication systems.     

A Discrete‐Amplitude Pulse Width Modulation for a High‐Efficiency Linear Power Amplifier

A new discrete‐amplitude pulse width modulation (DAPWM) scheme for a high‐efficiency linear power amplifier is proposed. A radio frequency (RF) input signal is divided into an envelope and a phase modulated carrier. The low‐frequency envelope is modulated so that it can be represented by a pulse whose area is proportional to its amplitude. The modulated pulse has at least two different pulse amplitude levels in order that the duty ratios of the pulse are kept large for small input. Then, an RF pulse train is generated by mixing the modulated envelope with the phase modulated carrier. The RF pulse train is amplified by a switching‐mode power amplifier, and the original RF input signal is restored by a band pass filter. Because duty ratios of the RF pulse train are kept large in spite of a small input envelope, the DAPWM technique can reduce loss from harmonic components. Furthermore, it reduces filtering efforts required to suppress harmonic components. Simulations show that the overall efficiency of the pulsed power amplifier with DAPWM is about 60.3% for a mobile WiMax signal. This is approximately a 73% increase compared to a pulsed power amplifier with PWM.