An extraction and analytical method for the determination of pesticide residues in fruits and vegetables has been developed. The method includes extraction with a pressurised liquid solvent containing a mixture of 1,1,1,2-tetrafluoroethane and toluene, and identification/quantification of pesticides using ultrahigh-performance liquid chromatography coupled to tandem mass spectrometry (UPLC/MS/MS). Validation studies were carried out to evaluate the performance of the method for the determination of 71 different pesticides and metabolites in tomato, cucumber, pepper, spinach, zucchini, grape, cherry, peach and apricot. Matrix-matched calibration curves were applied and correlation coefficients (r(2)) came out to be greater than 0.99. Limit of quantification (LOQ) values of the active substances were found to be lower than the maximum residue limits (MRL) according to regulations in Turkey. The recovery values were found to be between 70% and 120% with relative standard deviations less than 20%. Based on these results, the proposed method is fast, cheaper, rugged and gives quantitative results with no additional clean-up steps. 相似文献
Solid‐state batteries can potentially enable new classes of electrode materials which are unstable against liquid electrolytes. Here, SnS nanocrystals, synthesized by a wet chemical method, are used to fabricate a Li‐ion electrode, and the electrochemical properties of this electrode are examined in both solid and liquid electrolyte designs. The SnS‐based solid‐state cell delivers a capacity of 629 mAh g?1 after 100 cycles and exhibits an unprecedentedly small irreversible capacity in the first cycle (8.2%), while the SnS‐based liquid cell shows a rapid capacity decay and large first cycle irreversible capacity (44.6%). Cyclic voltammetry (CV) experiments show significant solid electrolyte interphase (SEI) formation in the liquid cell during the first discharge while SEI formation by electrolyte reduction in the solid‐state cell appears negligible. Along with CV, X‐ray photoelectron spectroscopy and energy dispersive spectroscopy are used to investigate the differences between the solid‐state and liquid cells. The reaction chemistry of SnS in solid‐state cells is also studied in detail by ex situ X‐ray diffraction and X‐ray absorption spectroscopy. The overarching findings are that use of a solid electrolyte suppresses materials degradation and electrolyte reduction which leads to a small first cycle irreversible capacity and stable cycling. 相似文献
Given that the performance of a lithium–oxygen battery (LOB) is determined by the electrochemical reactions occurring on the cathode, the development of advanced cathode nanoarchitectures is of great importance for the realization of high‐energy‐density, reversible LOBs. Herein, a robust cathode design is proposed for LOBs based on a dual‐phasic carbon nanoarchitecture. The cathode is composed of an interwoven network of porous metal–organic framework (MOF) derived carbon (MOF‐C) and conductive carbon nanotubes (CNTs). The dual‐phasic nanoarchitecture incorporates the advantages of both components: MOF‐C provides a large surface area for the oxygen reactions and a large pore volume for Li2O2 storage, and CNTs provide facile pathways for electron and O2 transport as well as additional void spaces for Li2O2 accommodation. It is demonstrated that the synergistic nanoarchitecturing of the dual‐phasic MOF‐C/CNT material results in promising electrochemical performance of LOBs, as evidenced by a high discharge capacity of ≈10 050 mAh g?1 and a stable cycling performance over 75 cycles. 相似文献
Following the fundamental research conducted by J. B. Goodenough, the important role of electron localization induced by elemental substitution is studied. The size and electron negativity of host and substituting ions are two important factors in tuning material properties such as local structure and transition metal (TM) oxygen covalency. However, another factor, electron localization, which is widely studied in catalyst research but largely overlooked for battery materials, deserves systematic studies. A combined investigation using synchrotronbased X-ray spectroscopy and theoretical calculations is carried out on the Li-Co-Mn-O model system in which the substituting cation Mn4+, with its 3d3 electronic structure, is used as a promoter for electron localization. Results indicate that electron localization greatly influences the Co O bond by making it less covalent, which increases the delithiation voltage. It is also found that during charge/discharge, electron localization tends to make TM K-edge X-ray absorption near edge spectroscopy (XANES) spectra show a more “rigid shift” behavior while electron delocalization makes the XANES exhibit a “shape change.” It clearly explains why the K-edge XANES data of some TM oxides show no “rigid shift” while the nominal valence states changed. This work highlights the importance of electron localization with guidance for XANES interpretation. 相似文献
At micro- and nanoscales, materials with high Young's moduli and low densities are of great interest for high-frequency micromechanical resonator devices. Incorporating carbon nanotubes (CNTs), with their unmatched properties, has added functionality to many man-made composites. We report on the fabrication of < or = 100-nm-thick laminates by sputter-deposition of aluminium onto a two-dimensional single-walled CNT network. These nanolaminates--composed of Al, its native oxide Al(2)O(3) and CNTs--are fashioned, in a scalable manner, into suspended doubly clamped micromechanical beams. Dynamic flexural measurements show marked increases in resonant frequencies for nanolaminates with Al-CNT laminae. Such increases, further supported by quasi-static flexural measurements, are partly attributable to enhancements in elastic properties arising from the addition of CNTs. As a consequence, these nanolaminate micromechanical resonators show significant suppression of mechanical nonlinearity and enhanced strength, both of which are advantageous for practical applications and analogous to biological nanocomposites, similarly composed of high-aspect-ratio, mechanically superior mineral platelets in a soft protein matrix. 相似文献
The purpose of this present study is to monitor the failure modes of pure resin and single layer of adhesively bonded lap joints using acoustic emission (AE) technique under tensile loading. Parametric analysis is performed using AE count rate, cumulative counts, time, frequency, amplitude and duration on the AE data obtained during the tensile test of adhesively bonded lap joints. After preliminary investigations in the parametric analysis, it was seen that AE amplitude parameter changes with the different AE events, thus failure modes were characterized using frequency analysis. Fast fourier transform (FFT) analysis has been proposed to identify the importance of peak frequency content of each failure mode corresponding to the AE hits using frequency FFT analysis. Short time fast fourier transform resulting frequency is correlated with FFT analysis of AE data, to find the peak frequency ranges for each of the failure modes. Scanning electron microscope as complementary, post-test inspection method is used to find microscopic evidence for the assumed assignment of failure modes. 相似文献
Positioning control of an underwater robot is a challenging problem due to the high disturbances of ocean flow. To overcome the high disturbance, a new underwater robot with tilting thrusters was proposed previously, which can compensate for disturbance by focusing the thrusting force in the direction of the disturbance. However, the tilting motion of the thrusters makes the system nonlinear, and the limited tilting speed sometimes makes the robot unstable. Therefore, an optimized controller is necessary. A new positioning controller is proposed for this robot using a vector decomposition method. Based on the dynamic model, the nonlinear force input term of the tilting thrusters is decomposed in the horizontal and vertical directions. Based on the decomposition, the solution is determined by a pseudo-inverse and null-space solution. Using the characteristics of the decomposed input matrix, the final solution can be found by solving a simple second-order algebraic equation to overcome the limitations of the tilting speed. The positioning was simulated to validate the proposed controller by comparing the results with a switching-based controller. Tracking results are also presented. In future work, a high-level control strategy will be developed to take advantage of the tilting thrusters by focusing the forcing direction toward the disturbance with a limited stability margin.