广钢转炉分厂2号方坯连铸机拉速问题的探讨

通过分析钢水在结晶器内凝固的不均匀性及对钢水结晶的热量平衡计算，讨论连铸中间包钢水温度、结晶器冷却水流量及进出水温差对拉坯速度的影响。     

不等波纹函数低通原型的理论及应用

本文提出不等波纹函数低通原型，并对其理论进行初步探讨。切比雪夫函数及最平坦型巴特活兹函数皆为其特例。文中给出不等波纹函数的几个性质，最后给出两个应用实例，消除耦合环自感部分的影响；抑制高次模的微带圆盘腔带通滤波器。     

减粘裂化分馏塔顶系统的腐蚀及防护

辽河石化分公司减粘裂化装置改炼辽河超稠油的减压渣油后 ,分馏塔顶系统由HCl -H2 S -HCN -有机酸 -H2 O引起的电化学腐蚀严重 ,其中油水分离器局部腐蚀速率达 3.1mm/a ,12AlMoV管束的空冷器运行不足两个月即发生泄漏。塔顶系统采用BZH - 1中和缓蚀剂、无机氨BZH - 913油溶性缓蚀剂综合注剂方案 ,使腐蚀得到控制     

1/f Noise separated from white noise with wavelet denoising

The low-frequency noise in the devices often appears to be a superposition of 1/f noise and white noise, which are induced by different physical mechanisms or microscopic defects. The separation of the two noises is necessary especially in the characterization of quality and reliability by means of noise measurement. The traditional separation method is usually used in frequency domain with limited frequency range, and the estimated value of exponent index γ for 1/f^γ noise has considerable error when the ratio of 1/f noise and white noise is smaller than 20 dB. In this paper, based on wavelet denoising theory, a new method is proposed to separate 1/f^γ noise from white noise in time domain and can be used to estimate γ values with much better accuracy even if the ratio of 1/f noise to white noise in low enough.     

北京谱仪漂移室读出电子学校准电路

本文介绍的电路可同时进行时间和电荷校准,它的校准量程大,精度高,稳定性好,可输出864路指数形校准信号,并可手动或程控。它的时间校准精度优于±250ps,电荷量校准精度优于±1％。     

企业滋生腐败与防范中的问题研究

分析了产生腐败的内在因素和外在环境;提出了企业在反腐败工作中存在的自律方面的问题、权利作用问题和监督部门的设置问题,并提出建立“分离分立不分家,制约制衡不掣肘”的防范机制。     

跋山水库抛石挤淤压重的试验研究

通过对水库坝前沉积的淤泥进行详细的试验分析,摸清淤泥的物理性质、状态指标,找出一条适宜的施工工艺,进行淤泥清淤,既能保证工程质量,又能加快进度,节省投资,为山区丘陵地区的水库加固提供新的经验。     

单晶凝固组织的样品尺寸效应

通过对不同直径的单晶样品的凝固实验，研究了样品尺寸对单晶凝固组织的影响规律，研究发现，随样品尺寸减小，单晶凝固组织被细化，尤其一次枝晶间距λ1和枝晶间γ′相尺寸对样品尺寸的依赖性更为明显；样品尺寸影响的要质在于此表面积的变化，进而对凝固过程温度梯度产生影响，最终作用于凝固组织和力学性能，一次枝晶间距λ1和枝晶间γ′尺寸与样品的比表面积近拟呈线性关系，样品尺寸变化，明显改变了单晶生长过程的温度梯度和合金的高温持久寿命。     

Effects of alloy additions on the microstructures and tensile properties of cast Co-Cr-Mo alloy used for surgical implants

The composition of the Co-Cr-Mo alloy has been modified by additions of nickel and some trace elements aluminium, titanium and boron. In this paper, the first part of the present study, the effects of alloy additions on the microstructures and tensile properties of the as-cast Co-Cr-Mo alloy are discussed. The effects of alloy additions on the fatigue behaviour of the alloy will be discussed in the second part of the present study. It is found that alloy additions do not seem to result in changes in the nature of the casting structure. A directional, coarse dendritic cast structure is produced in the modified alloys as in the base alloY. However, the alloy additions affect the carbide precipitations and the formation of some fine details of the microstructure such as dislocations, stacking faults and twins produced during the solidification. A considerable improvement in the transient mechanical properties, especially in the tensile ductility, is achieved by modifying the base alloy with alloy additions.