Formation and Characterization of 1.5-Monolayer Self-Assembled InAs/GaAs Quantum Dots Using Postgrowth Annealing

In this paper, we report that low-density InAs/GaAs quantum dots (QDs) can be formed by postgrowth annealing the samples with 1.5-monolayer (ML) InAs coverage, which is thinner than the critical layer thickness for the Stranski-Krastanov growth. The annealing procedure was performed immediately after the deposition of the InAs layer. The effects of annealing time and annealing temperature on the dot density, dot size, and optical characteristics of the QDs were investigated. The optimum annealing conditions to obtain low-density QDs are longer than 60 s and higher than 500degC . Meanwhile, no luminescence can be observed for the wetting-layer, which may suggest that the postgrowth annealing will make the wetting layer thinner and thus reduce the effects of wetting layer on carrier relaxation and recombination. On the other hand, we observe that a decrease of the PL intensity at the annealing conditions of 60 s and 515degC , which is possibly due to the increasing surface dislocations resulted from the In adatom desorption at higher annealing temperature.     

多部件设备维修问题研究及遗传算法求解

合理组织设备维修，缩短设备维修时间是生产运营管理的一个重要环节。本文探讨了多部件设备维修的有效组织问题。考虑到维修工人对拆分后设备的不同部分具有不同的维修效率，提出了一种基于维修时间优化的决策方法，将其与经典指派方法进行了比较；进一步地，对这一NP-hard问题设计了遗传算法，通过数值例子讨论了其求解有效性。     

Experimental and analytical studies of innovative prestressed concrete box-girder bridges

This paper presents experimental and analytical results of four scaled prestressed concrete box-girder bridges with corrugated steel webs. The location of prestressing strands at both ends of the specimens and the thickness of end diaphragms are the two major parameters. Based on the experimental results of all four specimens, their seismic behavior is critically examined, including hysteretic loops, ductility factor, dissipated energy, and failure mode, etc. It was found that both the thickness of end diaphragms and the location of prestressing strands at both ends of the specimens are insignificant when the specimens failed at the mid-span due to concrete crushing, and the proposed analytical model can be used to predict the load-displacement relationship of such bridges.     

辽河催化裂化澄清油中间馏分热反应研究

采用先加入絮凝剂脱灰，再经减压蒸馏切割420～500℃馏分的方法，将辽河催化裂化澄清油预处理，考察了澄清油、加入絮凝剂脱灰后的澄清油以及脱灰后再减压蒸馏所得的中间馏分这3种原料在热转化过程中中间相的转化历程，并采用偏光显微镜观察热转化产物。结果表明，澄清油预处理效果明显，所得中间馏分具有较低的H／C原子比（nH／nC）和适宜的组成分布，是生产针状焦的理想原料。热转化产物的光学组织结构属于各向异性发达的广域-流线型结构。     

Dynamic RSVP protocol

RSVP is a resource reservation setup protocol that can be used by a host to request specific QoS for multicast multimedia flows on the Internet. Multiprotocol label switching (MPLS) architecture also needs RSVP. The fact that the resolutions of the display system used in different receiver nodes might have different, multi-resolution characteristics is supported in the MPEG-4 standard, and the EZW compression algorithm can cease decoding at any point in the bitstream. However, RSVP does not provide a more flexible mechanism. In this article we propose an extension of RSVP to provide the needed mechanism, coined dynamic RSVP (DRSVP), to dynamically adjust reserved resources on nodes without much effort. It provides different video resolutions to different receiver nodes with different needed reserved resources. Therefore, it does not waste precious Internet resources to transmit unnecessary multimedia packets.     

高能 X 射线工业 CT 技术的研究进展

目的 研究分析了国内外高能X射线工业CT技术的进展情况，方法 通过有关文献资料，对目前国际上主要的高能X射线工业CT技术及设备进行评述。结果和结论 对美国、德国等发达国家的高能X射线工业CT设备、线阵探测器、面陈探测器及重建算法进行了分析。     

SiC颗粒增强铝基复合材料切削表面分形维数及其与抗磨损性能的关系

做为一种耐磨性能很好的材料 ,SiC颗粒增强铝基复合材料切削加工表面具有分形特征。实际研究表明SiC颗粒增强铝基复合材料切削加工表面分形维数与抗磨损性能有密切关系 ,本文还分析了表面分形维数越大其抗磨损性能越强的机理。     

A novel technique for profiling the lateral n- dopingconcentrations of submicron LDD MOS devices

This paper reports a simple I-V method for the first time to determine the lateral lightly-doped source/drain (S/D) profiles (n^- region) of LDD n-MOSFETs. One interesting result is the direct observation of the reverse-short-channel effect (RSCE). It is observed that S/D n^- doping profile is channel length dependent if reverse short-channel effect exists as a result of the interstitial imperfections caused by Oxide Enhanced Diffusion (OED) or S/D implant. Not only the lateral profiles for long-channel devices but also for short-channel devices can be determined. One other practical application of the present method for device drain engineering has been demonstrated with a LATID MOS device drain engineering work. It is convincible that the proposed method is well suited for the characterization and optimization of submicron and deep-submicron MOSFETs in the current ULSI technology     

Stress analysis of a cantilevered fixed partial denture with normal and reduced bone support

A two-dimensional finite element model was constructed to analyze the simulated mechanical behavior of a cantilevered fixed partial denture. The variations of the models were made by altering the degree of bone support, the number of splinted abutments, and the length of the pontics. High stress concentrations were observed around the connectors of the fixed prosthesis and the tooth closest to the cantilever. Reduced bone support increased the deflection and stress concentrations. There was reduction in displacement and stress concentration when the teeth were splinted together. To improve the prognosis of the fixed partial denture cantilever, the number of abutments should be increased and the number of pontics decreased.     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.