Air bearing design, optimization, stability analysis andverification for sub-25 nm flying

Three sub-25 nm fly height sliders are presented for near contact recording. The designs are geared towards the goal of achieving 10 Gb/in ² areal density. The optimization procedure presented shows promise for facilitating achievement of this goal. The dynamic simulations show the stability of these designs when disturbed from their steady state conditions     

矩形件排样的一种优化算法

排样问题是一种总体资源分配问题，这里根据矩形件排样的工艺要求，提出了矩形件排样的一种近似算法，将一块板材分成三部分，每部分排一种零件，使得减料方便，提高了劳动生产率。     

港口起重机金属结构裂纹的诊断与维修

起重机金属结构常见的故障有裂纹、变形、严重锈蚀、刚度不够等。其中裂纹是门机最为常见的故障，占金属机构故障的80％以上。虽然金属结构的设计都符合常规设计的强度要求，但往往还是不可避免有裂纹产生。这是因为材料内部总难免在夹渣、气孔，加工的过程中可能有毛刺、划伤，焊接过程中存在未焊透等。在变应力的作用下，存在缺陷的部位或者应力最大部位往往最先出现疲劳裂纹，随着应力循环次数的增加，裂纹缓慢扩展直至达到临界尺寸而破坏。     

内蒙古煤系高岭土作为FCC催化剂基质的研究

研究两种内蒙古煤系高岭土（1^＃、2^＃）的化学组成、晶体结构并与苏州高岭土进行了比较。对三种高岭土进行酸改性，利用BET、吡啶-TPD和微反测试分别研究改性前后高岭土的性能特点。并将内蒙古高岭土1^＃与苏州高岭土采用半合成方法合成了FCC催化剂，测定了其裂化活性。研究结果表明，内蒙古1^＃具有较良好的晶体结构和化学组成，经酸改性后比表面积大大增加，具有合适的孔径分布，裂化活性较好，可以取代苏州高岭土作为FCC催化剂的基质。     

A Novel Athermal 40-Channel DWDM Multi/Demultiplexer Based on the Combination of AWGs and Interleaver

An athermal 40-channel dense wavelength-division-multiplexing multi/demultiplexer using a novel combination technology is proposed. It consists of one 1times4 100- to 400-GHz spacing interleaver filter and four sub-arrayed-waveguide gratings (AWGs). The temperature-dependent wavelength shift of the combined device is successfully suppressed to 0.058 nm in the -20degC to 70degC temperature range. Moreover, the combined device's adjacent crosstalk (typically -35 dB) is much better than conventional AWGs (typically -25 dB).     

论王光祈的“少年中国”理想

王光祈的“少年中国”理想，是以“少年意大利”为基础，汲取五四时期社会主义思潮的积极成分而形成的。创造“少年中国”在“人”的方面，是从改造中国少年入手，同时注重青年学生与平民的改造，注重劳动阶级、智识阶级与资产阶级的改造与联合；在“事”的方面，积极开展社会事业和社会活动，且必须经过社会分工与国际分工。可见，他的这种理想是典型的社会改革主张，在早期带有无政府主义色彩，自始至终具有强烈的民族主义情感。     

Ultrasound‐activated Knoevenagel condensation of malononitrile with carbonylic compounds catalysed by alkaline‐doped saponites

α,β‐Unsaturated nitriles have been synthesized by Knoevenagel condensation of a carbonylic compound with malononitrile, assisted by sonochemical irradiation. Two alkaline‐promoted clays (Li⁺‐ and Cs⁺‐exchanged saponites) have been employed as catalysts. The influence of the carbonylic compound (benzaldehyde or cyclohexanone) and the use of a solvent on the catalytic activity have been studied. Remarkable increase in the conversion values has been found when the reaction is activated by ultrasound, as compared with the thermal activation. In this green, solvent‐free procedure, α,β‐unsaturated nitriles have been produced in very high yields (97%) when the Cs⁺‐saponite is used as catalyst. Copyright © 2004 Society of Chemical Industry     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

200kA预焙槽节能降耗的几点尝试

通过对200kA预焙槽节能方面做的几点尝试，探索出了200kA预焙电解槽在节约能源方面的措施，并取得了较好的节能效果。     

山东改造工程旧房质量检测

结合某成品仓库改作商业用房的工程实例,对该建筑进行了详细的检测与分析,并根据结果提出了针对性的加固方案,并对加固效果进行了探讨,为工程改造提供了依据,可供类似工程借鉴。