Gamma‐ray irradiation effect of polyethylene on dimaleimides as a class of new multifunctional monomers

Multifunctional monomers, m‐xylylenedimaleimide, p‐phenylenedimaleimide, m‐phenylenedimaleimide, and p‐phenylenedinadimide, all of which have maleimide groups, were synthesized to increase thermal and radiation stabilities. The synthesized multifunctional monomers showed good compatibility with low‐density polyethylene (LDPE). Mixtures of LDPE and these multifunctional monomers were irradiated with γ‐rays from a Co‐60 source at room temperature in a nitrogen atmosphere. The absorbed dose ranged from 0 to 160 KGy. Among these multifunctional monomers, m‐xylylenedimaleimide was the best in gel fraction enhancement. Crosslinked LDPE with m‐xylylenedimaleimide displayed a higher modulus than that of crosslinked LDPE with triallyl cyanurate. For the elongation property, LDPE with m‐xylylenedimaleimide as a multifunctional monomer showed better results than that with commercial multifunctional monomers such as triallyl cyanurate (TAC) and trimethylol propane triacrylate (TMPTA). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2339–2345, 2003     

The effct of asymmetries of die exit geometry on extrudate swell and melt fracture

Experimental investigations were performed to see how the die exit geometry and the extrusion velocity influence on extrudate swell and melt fracture for several polymer melts [low-density polyethylene, styrene-butadiene rubber (SBR) and SBR/HAF (carbon black) compound]. Four different types of die exit geometry were considered; 0° (symmetric. usual capillary die), and 30°, 45° and 60° (asymmetric dies) were chosen for the die exit angle. Extrudate diameters were measured without draw-down under isothermal condition. Polymer melts were extruded into an oil that has the same density and temperature as those of the extrudate. Extrudate swells from dies with different diameters were correlated with volumetric flow rates. It was observed that the extrudate swell increases with increasing volumetric flow rate and exhibits through a minimum value at about 45° die exit angle. As to the fracture phenomena, it was observed that the critical shear for the onset of melt fracture increases with the increasing die exit angle up to 45°. However, for 60° die exit angle, the onset of melt fracture is again similar to that of 0° exit angle.     

Synergic influence of a surfactant and ultrasonication on the preparation of soluble,conducting polydiphenylamine/silica‐nanoparticle composites

Conducting polydiphenylamine was used to encapsulate silica nanoparticles through the oxidative polymerization of diphenylamine in the presence of ultrasonic irradiation. The polymerization was performed in the presence of sodium lauryl sulfate as a surfactant. Experiments performed in the absence of ultrasound clearly demonstrated that the application of ultrasonication played multiple roles in the preparation of a composite of polydiphenylamine with silica nanoparticles. Ultrasonication dispersed the silica nanoparticles, converted sodium lauryl sulfate to lauryl alcohol, and augmented the dispersion of the silica‐nanoparticle/polydiphenylamine composite in an organic medium. Silica‐nanoparticle/polydiphenylamine composites were also prepared in the absence of ultrasound and/or sodium lauryl sulfate. The silica‐nanoparticle/polydiphenylamine composites were characterized with Fourier trans form infrared spectroscopy, ultraviolet–visible/near‐infrared spectroscopy, and thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3912–3918, 2006     

Preparation of Monodisperse ZrO2 by the Microwave Heating of Zirconyl Chloride Solutions

Based on the principle that the solubility of a salt decreases as the dielectric constant of the solvent decreases, zirconia powders were prepared by heating a zirconyl chloride solution with a 2-PrOH-water mixture as the solvent. The morphology, size, and size distribution of the resulting particles were highly sensitive to the heating method used on the starting solution. Particles formed under conventional heating methods were polydisperse, agglomerated spherical, or irregularly shaped because of inhomogeneous precipitation through the temperature gradient, the shear force induced by stirring, compositional nonuniformity, and the low heating rate. The present study demonstrated that microwaves provide an excellent means of heating uniformly and rapidly without stirring. The particles resulting from microwave treatment were monodisperse and spherical, with a mean diameter of 0.28 μm.     

Numerical study of coal particle cluster combustion under quiescent conditions

Behavior of ignition and combustion of coal particle cluster under a quiescent condition was numerically simulated by solving balance equations of mass and enthalpy with combustion kinetic models of volatiles and char. Two-flame structure, one flame penetrating into the cluster and the other moving out of the cluster, was predicted during the combustion of coal particle cluster. Effects of radiative heat transfer, group number, ambient temperature, coal particle size, and oxygen concentration on ignition and combustion of coal particle clusters were also analyzed. Simulations indicated that the gas volume fraction of coal particle cluster increases with time after devolatilization. Gas velocity passing through the cluster surface varied significantly at volatile liberation. The ignition time delay was reduced with the increase of ambient temperature. The cluster devolatilization rate and char burning rate increased while the ignition time delay decreased with the increase of ambient oxygen concentration.     

Catalytic characteristics of various rubber-reinforcing carbon blacks in decomposition of methane for hydrogen production

Carbon black has recently been reported to act as an effective catalyst for methane decomposition and to exhibit stable catalytic behavior despite carbon deposition, and thus it can be used for CO₂-free production of hydrogen from natural gas. In this work, various carbon blacks with different primary particle size were investigated with respect to methane decomposition under atmospheric pressure from 1123 to 1223 K. Catalytic characteristics, such as activity, activation energy and reaction order, were investigated and compared. It was observed that with decreasing primary particle size (or increasing specific surface area), the specific activity increased and the activation energy decreased. The reaction orders for various pelletized, rubber-reinforcing carbon blacks were 0.6–0.7, about the same regardless of the primary particle size, while they were near 1 for fluffy carbon blacks. Fluffy carbon black showed higher activity and activation energy than the pelletized carbon black of the same primary particle size. Changes of the surface morphology during carbon deposition were observed by TEM. Variations of the number of active sites were discussed in regard of the primary particle size, carbon deposition and binder. The presence of different types of active sites was also suggested.     

Mobile phase composition for resolving whey proteins in reversed-phase high performance liquid chromatography

Reversed-phase high-performance liquid chromatography was successfully developed for the simultaneous and rapid separation for the main whey proteins, α-Lactalbumin and β-Lactoglobulin. This method consisted of a linear gradient of the two mobile phases of 0.1% trifluoroacetic acid in water and 0.1% trifluoroacetic acid in acetonitrile. The total run time for this separation was approximately 30 min, and α-Lactalbumin was eluted followed byβ- Lactoglobulin. The injection volume was fixed at 20 μl and the flow rate was 1 ml 1/min. The optimum mobile phase composition and gradient conditions to separate α-Lactalbumin and β-Lactoglobulin (A+B) were experimentally obtained at the 15 μm particle with a pore size of 300 Å on the linear-gradient mode.     

Effects of Acetic Acid on the Crystallization Temperature of Sol–Gel-Derived MgO Nano-Powders and Thin Films

The influences of acetic acid addition to Mg-methoxide on the stability of the precursor and the crystallization behavior of sol–gel-derived MgO nano-powders and thin films were investigated using X-ray powder diffraction, transmission electron microscopy, Fourier-transformed infrared spectroscopy, and thermogravimetry. The addition of acetic acid enhanced the stability of the alkoxide against precipitation. Moreover, during postheat treatment of the gel powders treated with acetic acid, a significantly lowered crystallization temperature (250°C) was observed as compared to the untreated counterpart (350°C). The low-temperature crystallization of MgO, induced by the modification of Mg-methoxide with acetic acid, was related to the decomposition of organics at a lower temperature. These results could be explained in terms of the decrease of the O–R bond strength depending on the increase in the alkyl group size. MgO thin films having a high degree of crystallinity were successfully obtained from the Mg-methoxide treated with acetic acid at 300°C. The low-temperature crystallization of sol–gel-derived MgO thin films showed the feasibility for their application as a protective layer in alternative current plasma display panel cells.     

Preparation and electrical properties of metal sulfides–amidoximated PAN composite film

To improve the electrical conductivity of polyacrylonitrile (PAN) film, metallic sulfides and PAN composite film were prepared by the chelating method. Dense PAN film and porous PAN film were prepared by dry process and wet process, respectively. These PAN films were treated to NH₂OH solution to introduce the amidoxime group coordinated with metallic ion. Cu⁺² and Cd⁺² ions were adsorbed to amidoximated PAN films, the sulfur ion was treated with metal-adsorbed PAN films, and thus CuS—and CdS–PAN composite films were prepared. The adsorptive capacity of amidoximated PAN film for the Cu⁺² ion was independent of the morphology of the PAN film, but the adsorptive capacity of the Cd⁺² ion on amidoximated PAN film was dependent on porosity of the polymer. Adsorptive capacity of amidoximated porous PAN film for Cd⁺² was improved about four times than that of amidoximated dense PAN film. The electrical conductivities of CuS–dense and porous PAN composite film were both 10^?1 S/cm in optimum condition, but because of the difference in adsorptive capacity, the electrical conductivities of CdS–dense and CdS–porous PAN composite films were 10^?9 S/cm and 10^?4 S/cm, respectively. Additionally, because CdS was known as a photoconductive material, the photoconductive properties of CdS–porous PAN composite film were investigated.     

A randomized algorithm for natural object colorization

Natural objects often contain vivid color distribution with wide variety of colors. Conventional colorization techniques, on the other hand, produce colors that are relatively flat with little color variation. In this paper, we introduce a randomized algorithm which considers not only the value of target color but also the distribution of target color. In essence, our algorithm paints a color distribution to a region which synthesizes color distribution of a natural object. Our approach models the correlation between intensity and color in HSV color space in terms of H – S, H – V and S – V joint histogram. During the colorization process, we randomly swap and reassign color of a pixel to minimize a cost function that measures color consistency to its neighborhood and intensity‐to‐color correlation captured in the joint histogram. We tested our algorithm extensively on many natural objects and our user study confirms that our results are more vivid and natural compared to results from previous techniques.