Simple culling methods for continuous collision detection of deforming triangles

We present a simple and efficient approach for continuous collision detection of deforming triangles based on conservative advancement. The efficiency of our approach is due to a sequence of simple collision-free conditions for deforming triangles. In our experiment, we show that our CCD algorithm achieves 2-30 times performance improvement over existing algorithms for triangle primitives.     

Performance of TZCD-MBOK watermarking scheme in T-DMB systems

Recently, watermarking based data transmission techniques using terrestrial digital TV signal have been proposed since they are also cost-free and can overcome the limitations of GPS. However, in the previous watermarking based methods, the detection accuracy is low and additional data rate is too low. Thus, we propose the throughput enhancement method by employing the TZCD-MBOK watermarking technique in T-DMB system. By applying the proposed scheme to T-DMB, it allows additional data transmission for disaster broadcasting and improves efficiency of data transmission in shadow region and indoor to mobile environment through watermarking spread code. From the simulation results, we confirm the proposed watermarking scheme affected on the existing T-DMB signal. Moreover, it was also confirmed that the system capacity increases as the power of additional watermarking signal rose. The results of the paper can be applied to wireless multimedia digital broadcasting systems.     

An investigation into vehicle rollover prevention by coordinated control of active anti-roll bar and electronic stability program

This paper presents a method for designing a controller that uses an active anti-roll bar (AARB) and an electronic stability program (ESP) for rollover prevention. ESP with longitudinal speed control (LSC) can carry out active braking to reduce vehicle speed and lateral acceleration to prevent a rollover. To enhance the rollover prevention capability of the ESP, an AARB is adopted. The controller for the AARB was designed based on linear quadratic (LQ) static output feedback (SOF) control methodology, which attenuates the effect of lateral acceleration on the roll angle and roll rate by control of the suspension stroke and the tire deflection of the vehicle. Although this AARB significantly increases ride comfort and rollover prevention, it has a drawback — the vehicle loses its maneuverability. Therefore, the ESP with LSC is used to overcome this drawback. Simulations showed that the proposed method was effective in preventing a rollover.     

Infiltration behaviour of an internal electrode and electrical properties of multilayer capacitors by electrode infiltration

The infiltration behaviour of a tin melt, as an internal electrode, to the porous layers, and the electrical properties of multilayer ceramic capacitors was investigated by electrode infiltration. By preventing green-state delamination between the dielectric green sheet and the carbon paste, uniform porous layers, 5 m thick, could be formed after sintering. When 15 vol % ceramic pillars were added to the carbon paste, the porous layer of the sintered samples could be considered as a porous solid formed by many pores larger than 4 m. The critical pressure for the infiltration of tin melt into such a porous layer was found to be 0.5 MPa. With a high infiltration pressure, the resistivity of multilayer capacitors was decreased to 10⁸–10⁹cm due to the growth of micro-defects formed on the surface of the dielectric layers during the lamination process.     

Dielectric properties and microstructural behaviour of B-site calcium-doped barium titanate ceramics

Dielectric properties and microstructural behaviour of Ba_1–x Sr _x Ti_1–y Ca _y O_3–y ceramics, where strontium and calcium were doped on the barium and titanium sites, respectively, within the range 0x0.24 and 0y0.05, were investigated. Calcium addition decreased the tetragonality,c/a, increased the unit cell volume, and lowered the Curie temperature, which were all attributed to the occupancy of Ca²⁺ ions on titanium sites. When sintered at a low oxygen partial pressure of 10^–9 MPa, a resistivity higher than 10¹¹ cm was maintained for the formulations containing B-site calcium substitution more than 0.5 mol %. With increasing the amount of calcium addition, the Curie peak was depressed and completely broadened for the compositions with calcium addition more than 3 mol %, where the average grain size was smaller than 1 m. Co-firing with nickel electrodes in a reducing atmosphere also depressed the Curie peak and inhibited the grain growth due to the diffusion of nickel into the dielectrics.     

Beam profile measurement of a solar-pumped iodine laser

Beam profile measurements have been made as a function of time within the laser pulse and C2F5I pressure. Measurements indicate that the profile is determined directly by the optical excitation volume, produced by the solar simulator, and that media distortion plays a minor role compared to the build up of quenching species during the lasing pulse.     

A study on the dynamic characteristics of the Korean Yi-dynasty bell type structure

The dynamic characteristics of the Korean Yi-dynasty bell type structure, including the acoustic effects, are analyzed both theoretically and experimentally. The numerical solutions of natural frequencies and mode shape for membrane and flexural behavior are obtained by using the NASTRAN program for the finite element method with plate shell elements of triangular and quadrilateral types. Test bells, A and B types similar to the Kap-Sa bell in Kong-Ju chosen among typical Korean Yi-dynasty bells, are manufactured on different scales to the original bell. To consider the effects of the variation of the structural dimension on the dynamic response, these bells are analyzed with respect to the variation of the thickness of the wall and the bottom rim and the asymmetric Dang-Jwas. The impact method with the Fast Fourier Transform Analyzer is adopted to experimentally assess the dynamic response. Results are in good agreement with the numerical solutions.     

The Interlaminar Bond Strength of Flexible Polymer-Metal Laminates

An alternative test method to the traditional 180° “T” peel test has been developed for the measurement of interlaminar bonding in three-ply (polyester/aluminium/polypropylene) flexible-packaging, laminate materials. The new test is thought to involve mixed mode I (opening) and mode II (shearing) failure, and takes into account the yielding of the polypropylene layer during testing. The method allows more direct comparisons between materials to be made, and allows the measurement of strong bonds, where a peel test would result in yield or fracture of the substrate arms before debonding.     

A study on the deposition of pyrolytic carbons from hydrocarbons

A new method for forming isotropic, laminar, and columnar pyrolytic carbons is proposed. For this, a low RPM (below 2.4 rpm) tumbling bed has been used to deposit pyrolytic carbons from hydrocarbon gases. All deposits were made on graphite substrates from propane and methane at a constant temperature of 1200°C. The microstructures of the pyrolytic carbons deposited were dependent on the flow pattern of the reactant gas, the rpm of the reactor, the hydrocarbon concentration, the nature of the hydrocarbon, and the geometry of the bed. Isotropic pyrolytic carbon is formed under deposition conditions where homogeneous nucleation occurs in the gas phase and at the gas flow conditions where the gas-borne droplets can collide on the substrate. Laminar carbon is formed under deposition conditions where homogeneous nucleation does not occur in the gas phase and at gas flow conditions where the carbon species existing in the bulk of the gas phase can collide on the substrate. Columnar carbon is formed when any carbon products existing in the bulk of the gas phase cannot collide on the substrate. The suggested deposition mechanism can also be applied to pyrolytic carbons deposited in a fluidized bed or in a stationary bed. In particular, isotropic carbon can be obtained even in a stationary bed if the requirements for the deposition of the isotropic carbon described above are satisfied.