Polypyrrole composite membrane with high permeability prepared by interfacial polymerization

Novel polypyrrole (PPy)/polydimethylsiloxane (PDMS) composite membrane was prepared by interfacial polymerization to make a very effective gas separation membrane. We found that Polymerized PPy films as thin as ～200 nm could be chemically synthesized as freestanding membranes by using the interfacial polymerization technique. Additionally, we show that difference morphology of PPys films was obtained by controlling polymerization rate and more dense films were formed at low polymerization rate. Wide X-ray diffraction study showed the d spacing value of the PPy film decreased from 4.89 å to 3.67 å by the rate of polymerization decreases. According to d spacing value decrease, selectivity of a PPy composite membrane was increased dramatically and permeability was reduced gradually. This high selectivity was derived from d spacing closed to the kinetic diameter of nitrogen. These results indicated that the permeability is controlled by the diffusion coefficient, reflecting the packed structure of the PPy film. The highest selectivity value of composite membrane that was prepared by interfacial polymerization was O₂/N₂=17.2 and permeability for O₂ was 40.2 barrer.     

Effect of Sintering Temperature on Thermoelectric Properties of p‐Bi2Te3 Alloys Produced by Gas Atomization

In this research, p‐type Bi₂Te₃–75% Sb₂Te₃ thermoelectric alloy powders were produced by gas atomization and subsequently sintered by hot pressing at different temperatures. The grain growth of the hot‐pressed samples was observed with increasing sintering temperature from 380°C to 460°C. The compressive strength increased with increasing hot‐pressing temperature due to the high relative density of bulk samples obtained at high temperatures. The effect of sintering temperature on thermoelectric (TE) properties was studied. The maximum power factor 3.48 mW/mK² was obtained for the sample hot pressed at 420°C due to the resulting high electrical conductivity and enhanced Seebeck coefficient values.     

关于Filon算法的一点注记

本文对谐波分析中数值积分的Filon公式提出了一点改进,改进后的算法在微机上得到实现,经实算表明,计算结果满足工程精度要求。     

Site-selective substitution and resulting magnetism in arc-melted perovskite ATiO3-δ (A = Ca,Sr, Ba)

Magnetic properties in perovskite titanates ATiO_3-δ (A = Ca, Sr, Ba) were investigated before and after arc melting. Crystal structure analysis was conducted by powder synchrotron X-ray diffraction with Rietveld refinements. Quantitative chemical element analysis was carried out by X-ray photoelectron spectroscopy. Magnetic measurements were conducted by vibrating sample magnetometer and X-ray magnetic circular dichroism (XMCD). The magnetic properties are found to be affected by impurities of 3d elements such as Fe, Co, and Ni. Depending on the composition and crystal structure, the occupation of the magnetic ions in perovskite titanates is selectively varied, which is interpreted to be the origin of the different magnetic behaviors in arc-melted perovskite titanates ATiO_3-δ (A = Ca, Sr, Ba). In addition, both formation of oxygen vacancies and the reduction of Ti⁴⁺ to Ti³⁺ during arc-melting also play a role as proven by XMCD. Nevertheless, preferential site occupation of magnetic impurities is dominant in the magnetic properties of arc-melted perovskite ATiO_3-δ (A = Ca, Sr, Ba).     

Interfacial tension measurement between immiscible polymers: improved deformed drop retraction method

This paper describes an improvement of the technique to measure interfacial tension in immiscible polymer blends. Our method is based on the droplet retraction method, in which one relates the kinetics of relaxation of a deformed droplet to the interfacial tension between the matrix and droplet. Previously, the problem with this technique has been the difficulty in preparing axisymmetric ellipsoidal droplets. In our work, we demonstrate that perfect axisymmetric ellipsoidal droplets are produced at a later stage of relaxation of short imbedded fibers. With this technique, we utilize the strengths of both the deformed droplet method and the imbedded fiber retraction method while overcoming their shortcomings. The interfacial tension value thus obtained was compared to that by conventional methods. Additionally, the effect of confinement by external walls on the interfacial tension measurement was studied. Confinement affects interfacial tension measurement when the gap between the walls is less than two times the equilibrium drop size.     

Synthesis and optimization of NASICON-type Li3V2(PO4)3 by adipic acid-mediated solid-state approach

We report the synthesis and optimization of NASICON-type carbon-coated Li₃V₂(PO₄)₃ by solid-state approach. Adipic acid (AA) is used as the source material for the carbon. Initially, the synthesis of monoclinic Li₃V₂(PO₄)₃ is optimized at a precalcination temperature of 300 °C for 4 h and 900 °C for 8 h under Ar flow to yield a single phase. Powder characterizations such as thermogravimetric–differential thermal analysis, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and particle size distribution are conducted, and the results are presented. The AA concentration is varied according to the total metal ion composition in the compound (0.05, 0.1, and 0.15 M). Electrochemical Li-insertion properties are evaluated in half-cell configurations between 3 and 4.8 V vs. Li at a current density of 0.1 mA cm^?2 at room temperature. Compared with the lower AA concentrations, Li/Li₃V₂(PO₄)₃ (0.15 M AA) cell exhibited discharge capacities of 178 and 147 mAh g^?1 for the 1st and 50th cycles, respectively, and a capacity retention of 83 % after 50 cycles, which is 11 % higher than that of the native compound. Li/Li₃V₂(PO₄)₃ (0.15 M AA) showed better rate performances and delivered discharge capacities of 173, 165, 150, 132, 105, and 76 mAh g^?1 at rates of 0.1, 0.2, 0.5, 1, 5, and 12 C, respectively. Electrochemical impedance spectroscopy reveals the enhancement in electronic conductivity profile after carbon coating.     

Enhanced impact strength of compatibilized poly(lactic acid)/polyamide 11 blends by a crosslinking agent

Maleated poly(lactic acid) (PLA-g-MA) was prepared through melt grafting of maleic anhydride onto a PLA backbone with the aid of a radical initiator. PLA-g-MA thus formed was incorporated into PLA/polyamide 11 (PA11) blends as a reactive compatibilizer. By morphological observation, it was assessed that PLA-g-MA lowered the interfacial energy and strengthened the interface between PLA and PA11. However, the compatibilized PLA/PA11 blends did not show significant improvement of impact strength compared with noncompatibilized PLA/PA11 blends. Measurements of the molecular weight and impact strength of PLAs compounded with various amounts of radical initiators revealed that decreased molecular weight of PLA by the radical initiator used for the preparation of PLA-g-MA is responsible for this unexpected result. To compensate the decrease of the molecular weight, a crosslinking agent was incorporated in the preparation step of PLA-g-MA. It was found that the crosslinking agent is effective in preventing the molecular weight reduction. As a result, the impact strength of the PLA/PA11 blend was enhanced to a great extent by the PLA-g-MA prepared with the crosslinking agent.     

Toxoplasma gondii GRA9 Regulates the Activation of NLRP3 Inflammasome to Exert Anti-Septic Effects in Mice

Dense granule proteins (GRAs) are essential components in Toxoplasma gondii, which are suggested to be promising serodiagnostic markers in toxoplasmosis. In this study, we investigated the function of GRA9 in host response and the associated regulatory mechanism, which were unknown. We found that GRA9 interacts with NLR family pyrin domain containing 3 (NLRP3) involved in inflammation by forming the NLRP3 inflammasome. The C-terminal of GRA9 (GRA9C) is essential for GRA9–NLRP3 interaction by disrupting the NLRP3 inflammasome through blocking the binding of apoptotic speck-containing (ASC)-NLRP3. Notably, Q200 of GRA9C is essential for the interaction of NLRP3 and blocking the conjugation of ASC. Recombinant GRA9C (rGRA9C) showed an anti-inflammatory effect and the elimination of bacteria by converting M1 to M2 macrophages. In vivo, rGRA9C increased the anti-inflammatory and bactericidal effects and subsequent anti-septic activity in CLP- and E. coli- or P. aeruginosa-induced sepsis model mice by increasing M2 polarization. Taken together, our findings defined a role of T. gondii GRA9 associated with NLRP3 in host macrophages, suggesting its potential as a new candidate therapeutic agent for sepsis.     

Thin film yttria-stabilized zirconia electrolyte for intermediate-temperature solid oxide fuel cells (IT-SOFCs) by chemical solution deposition

A 500 nm thick thin film YSZ (yttria-stabilized zirconia) electrolyte was successfully fabricated on a conventionally processed anode substrate by spin coating of chemical solution containing slow-sintering YSZ nanoparticles with the particle size of 20 nm and subsequent sintering at 1100 °C. Incorporation of YSZ nanoparticles was effective for suppressing the differential densification of ultrafine precursor powder by mitigating the prevailing bi-axial constraining stress of the rigid substrate with numerous local multi-axial stress fields around them. In particular, adding 5 vol% YSZ nanoparticles resulted in a dense and uniform thin film electrolyte with narrow grain size distribution, and fine residual pores in isolated state. The thin film YSZ electrolyte placed on a rigid anode substrate with the GDC (gadolinia-doped ceria) and LSC (La_0.6Sr_0.4CoO_3?δ) layers deposited by PLD (pulsed laser deposition) processes revealed that it had fairly good gas tightness relevant to a SOFC (solid oxide fuel cell) electrolyte and maintained its structural integrity during fabrication and operation processes. In fact, the open circuit voltage was 1.07 V and maximum power density was 425 mW/cm² at 600 °C, which demonstrates that the chemical solution route can be a viable means for reducing electrolyte thickness for low- to intermediate-temperature SOFCs.     

Effect of zone drawing on the structure and properties of melt‐spun poly(trimethylene terephthalate) fiber

Melt‐spun poly(trimethylene terephthalate) (PTT) fibers were zone‐drawn and the structures and properties of the fibers were investigated in consideration of the spinning and zone‐drawing conditions. The draw ratio increased up to 4 with increasing drawing temperature to 180°C, at a maximum drawing stress of 220 MPa. Higher take‐up velocity gave lower drawability of the fiber. The PTT fiber taken up at 4000 rpm was hardly drawn, in spite of using maximum drawing stress, because a high degree of orientation had been achieved in the spinning procedure. However, an additional enhancement of birefringence was observed, indicating a further orientation of PTT molecules by zone drawing. The exotherm peak at 60°C disappeared and was shifted to a lower temperature with an increase in the take‐up velocity, which means that the orientation and crystallinity of the fiber increased. The d‐spacing of (002) plane increased with increasing take‐up velocity and draw ratio, whereas those of (010) and (001) planes decreased. In all cases, the crystal size increased with take‐up velocity and draw ratio. The cold‐drawn PTT fiber revealed a kink band structure, which disappeared as the drawing temperature was raised. The physical properties of zone‐drawn PTT fibers were improved as the draw ratio and take‐up velocity increased. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3471–3480, 2001